Weed Eater 530163368 HOW to Stop Your Unit, HOW to Start Your Unit, Starting a Warm Engine

Page 5

container momentarily to assure that the fuel is thoroughly mixed. Always read and follow the safety rules relating to fuel before fueling your unit.

IMPORTANT

Experience indicates that alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during stor- age. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, empty the fuel system before stor- age for 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. Never use engine or carburetor clean- er products in the fuel tank or permanent dam- age may occur. See the STORAGE section for additional information.

HOW TO STOP YOUR UNIT

S To stop the engine, move the ON/OFF switch to the OFF position.

SIf engine does not stop, move choke to the FULL CHOKE position.

Engine Choke Lever

ON/OFF

Switch

FULL HALF OFF

HOW TO START YOUR UNIT

WARNING: The trimmer head will turn while starting the engine. Avoid any con- tact with the muffler. A hot muffler can cause serious burns.

STARTING A COLD ENGINE (or a warm engine after running out of fuel)

Starting Position

1.Set unit on a flat surface.

2.Move ON/OFF switch to the ON position.

3.Slowly press the primer bulb 6 times.

4.Move choke lever to the FULL CHOKE position.

5.Squeeze the throttle trigger fully and hold through all remaining steps.

Starter Handle

Choke

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Lever

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Muffler

Primer Bulb

6. Pull starter rope handle sharply until engine sounds as if it is trying to start, but do not pull rope more than 6 times.

7. As soon as engine sounds as if it is trying to start, move choke lever to HALF CHOKE position.

8. Pull starter rope sharply until engine runs, but no more than 6 pulls. NOTE: If the en- gine doesn’t start after 6 pulls (at the HALF CHOKE position), move the choke lever to the FULL CHOKE position and press the primer bulb 6 times. Squeeze and hold the throttle trigger and pull the starter rope 2 more times. Move the choke lever to the HALF CHOKE position and pull the starter rope until the engine runs, but no more than 6 pulls. If the en- gine still doesn’t start, it is probably flooded. Proceed to STARTING A FLOODED ENGINE.

9. Once the engine starts, allow it to run 10 seconds, then move the choke lever to the OFF CHOKE position. Allow the unit to run for 30 more seconds at OFF CHOKE before releasing the throttle trig- ger. NOTE: If engine dies with the choke lever in the OFF CHOKE position, move the choke lever to the HALF CHOKE position and pull the rope until engine runs, but no more than 6 pulls.

STARTING A WARM ENGINE

1.Move ON/OFF switch to the ON position.

2.Move the choke lever to the HALF CHOKE position.

3.Squeeze and hold the throttle trigger. Keep throttle trigger fully squeezed until the en- gine runs smoothly.

4.Pull starter rope sharply until engine runs, but no more than 5 pulls.

5.Allow engine to run 15 seconds, then move the choke lever to OFF CHOKE.

NOTE: If engine has not started, pull starter rope 5 more pulls. If engine still does not run, it is probably flooded.

STARTING A FLOODED ENGINE

Flooded engines can be started by placing the choke lever in the OFF CHOKE position; then, pull the rope to clear the engine of ex- cess fuel. This could require pulling the starter handle many times depending on how badly the unit is flooded. If the unit still doesn’t start, refer to TROUBLESHOOTING TABLE or call 1-800-554-6723.

5

Image 5
Contents 23/03 530163368Fuel Safety Operator SafetyUnit / Maintenance Safety Transporting and Storage Cutting SafetyAttaching the Handle Attaching ShieldKnow Your Trimmer ON/OFF SwitchPrimer Bulb ChokeHOW to Start Your Unit HOW to Stop Your UnitStarting a Warm Engine Starting a Flooded EngineTwist and Edge Operating PositionTrimmer Line Advance Cutting MethodsClean AIR Filter Inspect and Clean Unit and LabelsCheck for Loose Fasteners and Parts Check for Damaged or Worn PartsCarburetor Adjustment Line ReplacementMuffler and Spark ARREST- ING Screen Replace Spark PlugFuel System Seasonal StorageEngine OtherTroubleshooting Table Cause Remedy Electrolux Home PRODUCTS, INC Warranty Commencement Date

530163368 specifications

The Weed Eater 530163368 is a powerful and efficient string trimmer designed for both homeowners and professionals seeking to maintain their lawns and gardens with precision. Known for its reliability and performance, this trimmer offers an array of features that make yard work easier and more effective.

One of the standout characteristics of the Weed Eater 530163368 is its lightweight design, which enhances maneuverability and reduces user fatigue during extended use. Weighing just under 10 pounds, this trimmer is easy to handle, allowing users to reach tight spots and navigate around obstacles like trees and flower beds without strain.

Equipped with a robust 25cc 2-cycle engine, the Weed Eater 530163368 delivers impressive power to tackle thick grass and stubborn weeds. The engine's design ensures efficient fuel consumption, allowing for longer operating times between refueling. Additionally, the trimmer employs a simple starting mechanism, making it easy for users to get it running without hassle.

The Weed Eater 530163368 features a dual-line bump feed system, which automatically feeds the cutting line as it wears down, ensuring uninterrupted operation. This feature minimizes downtime associated with manual line adjustments, making it particularly appealing for users who prefer a more convenient and efficient cutting experience. The trimmer head is designed for easy line replacement, allowing for quick changes when needed.

Another significant aspect of the Weed Eater 530163368 is its adjustable shaft. The trimmer comes with an ergonomic handle and telescopic shaft, which can be modified to accommodate users of different heights. This customization enhances comfort and control during use, promoting better handling and more accurate trimming.

Additionally, the Weed Eater 530163368 is compatible with a range of attachments, expanding its functionality beyond simple trimming. Users can easily convert it into a multi-tool, making it adaptable for various gardening tasks such as edging and cultivating.

In summary, the Weed Eater 530163368 stands out as a versatile and powerful string trimmer, ideal for maintaining pristine lawns and gardens. Its lightweight design, reliable engine, efficient bump feed system, and adjustable features make it a top choice for both homeowners and landscaping professionals alike. This trimmer is engineered to deliver impressive results while ensuring user comfort and convenience. With its innovative technologies and robust characteristics, the Weed Eater 530163368 is a solid investment for anyone looking to keep their outdoor spaces looking their best.