McCulloch Aug-42 instruction manual Spark Plug, Chain Sharpening, Carburetor Adjustment

Page 14

After each use, ensure ON/STOP switch is in the STOP position, then clean all sawdust from the guide bar and sprocket hole.

To maintain guide bar:

SMove ON/STOP switch to the STOP posi- tion.

S Loosen and remove bar nuts and chain brake. Remove bar and chain from saw.

SClean the oil holes and bar groove after each 5 hours of operation.

Remove Sawdust From

Guide Bar Groove

Oil Holes

S Burring of guide bar rails is a normal process of rail wear. Remove these burrs with a flat file.

SWhen rail top is uneven, use a flat file to re- store square edges and sides.

File Rail Edges

and Sides

Square

Worn Groove

Correct Groove

Replace guide bar when the groove is worn, the guide bar is bent or cracked, or when excess heating or burring of the rails occurs. If replacement is necessary, use only the guide bar specified for your saw in the repair parts list or on the decal located on the chain saw.

SPARK PLUG

The spark plug should be replaced each year to ensure the engine starts easier and runs better. Ignition timing is fixed and non- adjustable.

1.Loosen 3 screws on cylinder cover.

2.Remove the cylinder cover.

3.Pull off the spark plug boot.

4.Remove spark plug from cylinder and discard.

5.Replace with Champion RCJ--7Y spark plug and tighten securely with a 19 mm socket wrench. Spark plug gap should be 0,5 mm.

6.Reinstall the spark plug boot.

7.Reinstall the cylinder cover and 3 screws. Tighten securely.

Cylinder

Cover

Spark

Plug Boot

Spark

Plug

CHAIN SHARPENING

WARNING: Failure to properly sharp- en the chain considerably increases the risk of kickback.

Chain sharpening is a complicated task that requires special tools. We recommend that you refer chain sharpening to a professional chain sharpener.

CARBURETOR ADJUSTMENT

WARNING: The chain will be moving during most of this procedure. Wear your pro- tective equipment and observe all safety pre- cautions. The chain must not move at idle speed.

The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the following conditions:

SChain moves at idle. See IDLE SPEED--T

adjusting procedure.

SSaw will not idle. See IDLE SPEED--T ad- justing procedure.

Idle Speed--T

Allow engine to idle. If the chain moves, idle is too fast. If the engine stalls, idle is too slow. Adjust speed until engine runs without chain movement (idle too fast) or stalling (idle too slow). The idle speed screw is located in the area above the primer bulb and is labeled T.

STurn idle speed screw (T) clockwise to in- crease engine speed.

STurn idle speed screw (T) counterclock- wise to decrease engine speed.

14

Image 14
Contents Manual DE Instrucciones Manuel D’INSTRUCTIONSBetriebsanweisung ON/STOP Identification What is WHAT?Identification of Symbols Safety Rules Plan AheadChain SAW Safety Equipment Operate Your SAW SafelyKickback Maintain Your SAW in Good Working OrderHandle Fuel with Caution Reduce the Chance KickbackWith the cutting chain Kickback Safety FeaturesMaintain Control Hand slips off the front handlebarAttaching the BAR & Chain AssemblyAttaching the Bumper Spike LoosenWheel Bar Knob Adjusting the tensionAdjusting Wheel Bar ToolFueling Engine Operating Your UnitBefore Starting Engine BAR and Chain Lubrication Chain BrakeChain Brake Cutting MethodsStarting a Warm Engine Important PointsNotch CUT and Felling the Tree Tree Felling TechniquesFelling Large Trees Cutting a Fallen TreeTypes of Cutting Used for Bucking Bucking Using a LOG or SUP- Port StandImportant points Bucking Without a SupportLimbing Service and AdjustmentsBAR Maintenance PruningChain Sharpening Carburetor AdjustmentSpark Plug Store in a dry area out of the reach of chil- dren Troubleshooting Table Cause RemedyStorage Long--term storageDeclaration of Conformity Technical Data Sheet Iida

Aug-42 specifications

The McCulloch Aug-42 is a remarkable piece of engineering that showcases innovation in the small engine and handheld power tool industry. This chainsaw, introduced by McCulloch, has made its mark for its reliability, efficiency, and ease of use, making it an excellent choice for both professional and amateur users.

At the heart of the Aug-42 is a powerful 42cc engine that provides optimal performance for cutting tasks. The engine's design emphasizes lightweight construction while maintaining durability, allowing for ease of maneuverability. This is especially beneficial for users who may be involved in lengthy cutting or trimming tasks, as the lightweight build reduces fatigue.

One of the standout features of the Aug-42 is its anti-vibration technology. This innovation significantly minimizes the vibrations felt by the user during operation, enhancing comfort and control. As a result, operators can work for extended periods without the discomfort typically associated with prolonged chainsaw use.

The Aug-42 also incorporates a strategized fuel delivery system that maximizes power while ensuring fuel efficiency. It features a catalytic muffler that not only reduces noise during operation but also lowers the emissions produced, making it a more environmentally responsible choice. This combination of power and eco-friendliness caters to today’s environmentally conscious consumers.

The chainsaw comes equipped with a side-access chain tensioning system. This allows users to adjust the chain tension without needing to remove the guide bar, resulting in quick and hassle-free adjustments in the field. This essential feature minimizes downtime and keeps the user focused on their task.

Safety is another priority in the design of the McCulloch Aug-42. It includes an automatic chain brake that halts the chain’s motion when unexpected movements occur, protecting the user from possible accidents. Additionally, the chainsaw has a comfortable grip handle designed to provide optimum control, even in wet conditions.

In summary, the McCulloch Aug-42 fuses power, efficiency, and safety into a robust, user-friendly package. Its advanced technologies, including anti-vibration systems, fuel efficiency features, and safety mechanisms, position it as a preferred choice for those needing a dependable chainsaw. Whether used for general yard work, tree trimming, or more significant outdoor projects, the Aug-42 stands as a testament to McCulloch’s commitment to quality and innovation in outdoor power equipment.