Troy-Bilt 604 manual Battery, Fuse, Charging

Page 23

NOTE: The hex flange nut has a right-handed thread pattern. Do NOT attempt to force the nut in the incorrect direction. Doing so may damage the nut and create a safety hazard.

Hex Flange Nut

Block of Wood

Spindle

Cutting Blade

Assembly

Figure 22

To properly sharpen the cutting blades, remove equal amounts of metal from both ends of the blades along the cutting edges. See Figure 23.

Sharpen the cutting edge straight across, parallel to the trailing edge, at a 25° to 30° angle. See Figure 23.

IMPORTANT: If the cutting edge of the blade has already been sharpened to within 5/8" of the wind wing radius, or if any metal separation is present, replace the blades with new ones. See Figure 23.

Worn Blade Edge

 

Blade Separation

Wind Wing

5/8" minimum Sharpen Edge Evenly

Figure 23

It is extremely important that each cutting blade edge be ground equally to maintain proper blade balance. An unbalanced blade will cause excessive vibration when rotating at high speeds, may cause damage to the tractor and result in personal injury. The blade can be tested by balancing it on a round shaft screwdriver. Grind metal from the heavy side until it balances evenly.

When replacing the blade, be sure to install the blade with the side of the blade marked ‘‘Bottom’’ (or with a part number stamped in it) facing the ground when the mower is in the operating position.

IMPORTANT: Use a torque wrench to tighten the blade spindle hex flange nut to between 70 foot- pounds and 90 foot-pounds.

BATTERY

The battery is sealed and is maintenance-free. Acid levels cannot be checked.

•Always keep the battery cables and terminals clean and free of corrosive build-up.

•After cleaning the battery and terminals, apply a light coat of petroleum jelly or grease to the terminals and over the positive terminal boot.

•Always keep the boot positioned over the positive terminal to prevent shorting.

IMPORTANT: If removing the battery for any reason, disconnect the NEGATIVE (Black) wire from it’s terminal first, followed by the POSITIVE (Red) wire. When re-installing the battery, always connect the NEGATIVE (Black) wire its terminal first, followed by the POSITIVE (Red) wire. Be certain that the wires are connected to the correct terminals. reversing them could change the polarity and cause damage to your engine’s alternating system.

Charging

If the unit has not been put into use for an extended period of time, charge the battery with an automotive-type 12-volt charger for a minimum of one hour at six amps.

WARNING: Batteries give off an explosive gas during and for some time after charging. Charge battery in a well ventilated area and do not allow a spark or an open flame near the battery.

FUSE

A fuse is installed in your tractor’s wiring harness to protect the tractor’s electrical system from damage caused by excessive amperage. Always use the same capacity fuse for replacement. If the electrical system does not function, or your tractor’s engine will not crank, first check to be certain that the fuse has not blown. It can be found under the hood mounted behind the top of dash panel on the support bar. Pull the fuse out and compare it with Figure 24 to determine if it is good or bad.

2020

GOODBAD

Figure 24

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents OPERATOR’S Manual Calling Customer Support Table of ContentsFinding Your Model Number General Operation Important Safe Operation PracticesChildren ServiceSlope Operation Do notSafety Labels found on your unit Or a Fence Post Slope GaugeTractor SET-UP Attachments & AccessoriesAttaching the Battery Cables Installing the Mulch KITControls Choke Control Ignition SwitchIndicator Monitor / Hour Meter Throttle Control LeverParking Brake Button PTO Power TAKE-OFF LeverLift Lever Autodrive PedalCruise Control Button Seat Adjustment LeverSafety Interlock Switches OperationStopping the Engine Setting the Cutting HeightSetting the Cruise Control Starting the EngineOperating the Headlights Using the Lift LeverEngaging the PTO Power TAKE-OFF Lever Driving on SlopesLeveling the Deck AdjustmentsMowing Front to Rear Seat AdjustmentSteering Adjustment PTO Power TAKE-OFF Adjustment Brake AdjustmentCarburetor Adjustment Changing Engine Oil MaintenanceEngine Front of Tractor Cleaning the Engine and DeckTo Lift Assembly Cutting Deck RemovalInch decks Changing the Deck BeltsLower Drive Belt Changing the Transmission Drive BeltsUpper Drive Belt Transmission Hole Cutting BladesCharging BatteryFuse Lubrication Trouble Possible Corrective Action Causes Troubleshooting GuidePart Description ModelElectrical System/Tractor Body Model Lift Assembly Model Steering Assembly Model Drive System 447 Power Take-off System Inch Deck Cutting Decks Briggs & Stratton Intek Twin Briggs & Stratton Intek Single Engine AccessoriesMANUFACTURER’S Limited Warranty for

604 specifications

The Troy-Bilt 604 is a versatile and reliable piece of equipment designed to meet the needs of homeowners and landscapers alike. Known for its robust performance and innovative features, this model stands out in the market for those requiring efficient yard maintenance.

One of the standout characteristics of the Troy-Bilt 604 is its powerful engine. Equipped with a reliable 4-cycle engine, it offers ample power for tackling various outdoor tasks, including cultivating, tilling, and soil preparation. This strong engine not only ensures performance but also translates into longevity, allowing users to depend on it for several seasons.

Another notable feature of the Troy-Bilt 604 is its patented front-tine design. This design provides excellent maneuverability in tight spaces, making it easier to work around garden beds and landscaping features. The adjustable tilling width is also a significant advantage, allowing users to switch between a narrow and wide tilling path based on their specific project needs. This flexibility helps optimize efficiency while minimizing time spent on each task.

The Troy-Bilt 604 incorporates advanced technologies that further enhance its functionality. For instance, the model is outfitted with easy-to-use controls, ensuring a user-friendly experience for both seasoned professionals and novice gardeners. The adjustable handlebars can be tailored to different heights, promoting comfort and reducing fatigue during operation.

Durability is a key attribute of the Troy-Bilt 604. Built with high-quality materials and reinforced components, this tiller is designed to withstand the rigors of frequent use in diverse environments. Users can have confidence in the machine's ability to handle tough soil conditions, as well as its resistance to wear and tear.

In addition to its impressive performance, the Troy-Bilt 604 is also designed with maintenance in mind. Features like easy-access air filters and oil drain ports simplify routine maintenance tasks, ensuring that the equipment runs smoothly for years to come.

Overall, the Troy-Bilt 604 combines power, versatility, and durability, making it an excellent choice for anyone looking to enhance their landscaping efforts. Whether you are preparing a new garden bed, tilling soil for planting, or maintaining an existing landscape, the Troy-Bilt 604 provides a reliable solution that meets various gardening needs with ease and efficiency.
Top Page Image Contents