Musical Fidelity X-P200 manual Operation, Introduction

Page 3

OPERATION

INTRODUCTION

Your X-P200 can be connected either as a conventional stereo amplifier, or alternatively in “bridge” mode as a mono amplifier with higher output power - see page 4 and 5 for connection details.

It is intended for use with a pre-amplifier or similar audio level source with a volume control. We highly recommend the matching X-Pre preamplifier also available from Musical Fidelity.

Two stereo pairs of RCA audio input sockets marked “A” and “B” on the rear panel allow a choice between either of these input sources. Simultaneous mixed A and B operation is not possible.

Whichever input is chosen, a fixed “line level” audio output from the selected source is available from the adjacent OUTPUT RCA sockets for onward connection to another amplifier. This is to allow for “bi-amplification” (see below).

BI-AMPLIFICATION

The X-P200’s OUTPUT sockets allow “bi- amplification” of a speaker system using suitable external amplifiers and crossover networks. This enables the speaker drive units to be powered separately, giving noticeable improvement in clarity, imaging and bass weight.

In this arrangement, typically one X-P200 is used to drive the “tweeter” (high frequencies), and another to drive the “woofer” (low frequencies) of each loudspeaker enclosure. Thus, two X-P200s would be needed for a stereo pair, or four in bridge mode.

(continued) . . .

If in doubt about bi-amplification, please contact your dealer for advice.

BEFORE SWITCHING ON . . . .

Plug the accessory IEC mains lead into the rear panel socket, then the other end into a wall outlet.

Turn the volume control on your pre- amplifier to minimum.

OPERATION

Press the POWER button on the X-P200 amplifier - the blue power LED on the front panel will light indicating that the unit is ready for use. However, for about six seconds no sound will be heard from your speakers, and the red mute LED will be lit, confirming initial mute action.

Press the INPUT selector button on the front panel to switch between A and B input as required. A corresponding blue LED above the button will light to confirm your selection.

Now adjust the volume control on your pre- amplifier to obtain the preferred sound level.

If “bridge” loudspeaker operation is required, press the MODE button on the front panel to switch over to this function. A corresponding blue LED above the button will light to indicate which system is in use. Press the MODE button again to revert to normal stereo.

Please note that if STEREO mode is accidently selected with the speakers wired for “bridge” operation, sound will be distorted, and lack bass. Similarly, if switched to BRIDGE mode with speakers wired for stereo operation, sound quality will

FACILITIES (see page 6)

Power indicator

Mute indicator

Input indicator

Loudspeaker

mode indicator

LED (blue)

LED (red)

LEDs (blue)

LEDs (blue)

INPUT

MODE

X - P 2 0 0

 

Power on/off push-

Input mode

Loudspeaker mode

button switch

push-button switch

push-button switch

Page 6 of 7

X-P200 Power Amplifier

 

X-P200 Power Amplifier

Page 3 of 7

Page 2 Page 4
Image 3
Page 2 Page 4
Contents 2 0 IMPORTANT! U.K. only Safety InformationIntroduction OperationInput Connections Connections

X-P200 specifications

The Musical Fidelity X-P200 integrated amplifier is a prominent audio component that has gained recognition for its high-quality sound reproduction and refined design. Emphasizing a balance of power and precision, it seamlessly integrates into any audiophile's home audio system.

One of the key features of the X-P200 is its high output power, reaching an impressive 100 watts per channel into 8 ohms. This power allows it to drive a wide range of speakers, providing robust performance and dynamic sound across various musical genres. The amplifier’s dual mono architecture ensures that each channel operates independently, allowing for enhanced stereo separation and improved soundstage.

The X-P200 employs sophisticated Class A/B amplification technology, which combines the advantages of both Class A and Class B designs. This results in low harmonic distortion and superior linearity, delivering a warm and detailed musical experience. Additionally, the amp boasts a high damping factor, which facilitates excellent control of the connected speakers, ultimately producing tight and articulate bass response.

In terms of connectivity, the X-P200 is equipped with a variety of inputs, including multiple line-level RCA inputs, allowing users to connect various sources such as CD players, tuners, and even digital audio players. The amplifier also features a headphone output, making it a versatile option for personal listening, while the built-in mute function adds convenience during use.

The construction of the X-P200 reflects a commitment to quality. Its robust chassis design minimizes resonance and external interference, ensuring that the components operate optimally. The amplifier's front panel features a sleek, minimalist aesthetic with simple controls that enhance usability without overwhelming the listener.

In summary, the Musical Fidelity X-P200 stands out as a powerful, versatile integrated amplifier that combines advanced amplification technologies with thoughtful design. It is an excellent choice for both casual listeners and serious audiophiles, providing a high-fidelity audio experience that truly captures the essence of the music. Whether used in a dedicated listening room or as part of a more extensive home audio setup, the X-P200 delivers performance and reliability, making it a worthwhile investment for any music enthusiast.
Top Page Image Contents