Troy-Bilt 030245 Assembly, Before Starting the Engine, Add Engine Oil, Add Fuel, When Adding Fuel

Page 7

Section 3: Assembly

5.Install e-ring with pliers, squeezing from top of e-ring to bottom of axle.

CAUTION

E-rings can cause eye injury.

E-rings can spring back and become airborne when installing or removing.

• Always wear eye protection when installing/removing e-rings.

6.Repeat step 4 and 5 to secure second wheel.

7.Tip generator so that engine side is down.

8.Line up holes in support leg with holes in generator frame.

9.Attach support leg using 2 capscrews (M8 x 16 mm) and 2 hex nuts.Tighten with a 13mm socket wrench and 13mm wrench.

10.Return generator to normal operating position (resting on wheels and support leg).

BEFORE STARTING THE ENGINE

Add Engine Oil

• Place generator on a level surface.

CAUTION

Any attempt to crank or start the engine before it has been properly filled with the recommended oil will result in equipment failure.

•Refer to engine operator’s manual for oil fill information.

•Damage to equipment resulting from failure to follow this instruction will void warranty.

•Refer to engine operator’s manual and follow oil recommendations and instructions.

NOTE: Check oil often during engine break–in. Refer to engine operator’s manual for recommendations.

NOTE: The alternator assembly rotates on a prelubricated and sealed ball bearing that requires no additional lubrication for the life of the bearing.

Add Fuel

NOTE: This gasoline engine is certified to operate on

gasoline. Exhaust Emission Control System: EM (Engine Modifications).

WARNING

Fuel and its vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

WHEN ADDING FUEL

•Turn generator OFF and let it cool at least 2 minutes before removing fuel cap. Loosen cap slowly to relieve pressure in tank.

•Fill fuel tank outdoors.

•DO NOT overfill tank. Allow space for fuel expansion.

•Wait for spilled fuel to evaporate before starting engine.

•Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition sources.

•DO NOT light a cigarette or smoke.

1.Use clean, fresh, regular UNLEADED gasoline with a minimum of 87 octane. DO NOT use fuel which contains Methanol. DO NOT mix oil with fuel.

2.Clean area around fuel fill cap, remove cap.

3.Slowly add regular unleaded gasoline to fuel tank. Be careful not to overfill. Allow at least 1.5" of tank space for fuel expansion (Figure 2).

Figure 2 - Fuel Expansion

AirSpace

Tank

Fuel

1.5”

 

4.Install fuel cap and let any spilled fuel evaporate before starting engine.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Questions? Preguntas? Helpline 1-888-611-6708 M-F8-5 CT Operator’s Manual / Manual del OperarioSafety Rules Table of ContentsEquipment Description When Transporting or Repairing Equipment When Adding or Draining FuelWhen Starting Equipment When Operating EquipmentWhen Testing for Engine Spark When Adjusting or Making Repairs to Your GeneratorKnow Your Generator Features and Controls SectionUnpack the Generator AssemblyInstall Wheel Kit Refer to and install the wheel kit as followsAdd Engine Oil AssemblyWhen Adding Fuel Before Starting the EngineSystem Ground Using the GeneratorConnecting to a Building’s Electrical System Section OperationStarting the Engine Connecting Electrical LoadsOperation Operating Generator120/240 Volt AC, 30 Amp, Locking Receptacle ReceptaclesGenerator Adapter Cord SET Stopping the EngineExample Power ManagementDont Overload Generator CapacitySpecifications MaintenanceGeneral Maintenance Recommendations Engine Storage Storage SectionStorage Generator StorageTroubleshooting Section TroubleshootingProblem Cause Correction TROY-BILT Portable Generator Owner Warranty Policy Limited WarrantyConserve Estas Instrucciones Reglas de SeguridadCuando Opere EL Equipo Sección 1 Reglas de SeguridadCuando Añada Combustible O Vacíe EL Depósito Cuando Ponga EN Funcionamiento EL EquipoCuando Ajuste O Haga Reparaciones a SU Generador PrecauciónCuando Pruebe LA Bujía DEL Motor Tomacorriente con Dispositivo de Seguridad de Características y ControlesConozca SU Generador Tomacorriente Dobles de 120 Voltios AC, 20 AmpInstale el Juego de Ruedas MontajeMontaje Desembalaje del GeneradorAgregue Combustible Sección 3 MontajeAntes DE Darle Arranque AL Motor Agregar Aceite al MotorConexión al Sistema Eléctrico de un Edificio OperaciónUSO DEL Generador Tierra del SistemaConexion De Cargas Electricas Sección 4 OperaciónOperando EL Generador Encienda el MotorVolt AC, 20 Amp, Receptáculos Dobles Receptáculos PrecauciónJuego DE Cables DEL Adaptador DEL Generador Parado Del MotorEjemplo No Sobrecargue GeneradorCapacidad Control de la EnergíaEspecificaciones MantenimientoRecomendaciones Generales DE Mantenimiento Almacenando el Motor Diagnositicos DE AveríasAlmacenamiento Almacenando el GeneradorGarantía Limitada Período DE Garantía

030245 specifications

The Troy-Bilt 030245 is a highly regarded garden tiller, designed to meet the needs of both amateur gardeners and seasoned horticulturists. It combines power, innovation, and user-friendly features to make soil preparation an efficient and effective process.

One of the standout features of the Troy-Bilt 030245 is its robust engine. Equipped with a dependable 208cc OHV engine, it delivers the power necessary to tackle tough soil conditions. This engine not only provides ample torque but also ensures easy starts, allowing users to begin their gardening tasks without delay.

The tiller is designed with a versatile 16-inch tilling width, making it ideal for various gardening needs, from small gardens to larger plots. This width allows for efficient coverage while still being manageable in tighter spaces. Additionally, the adjustable tilling depth feature gives users control over their tilling operations, allowing them to prepare soil for seed planting or to aerate existing gardens effectively.

Another significant characteristic of the Troy-Bilt 030245 is its patented Forward and Reverse Tilling technology. This feature enables users to reverse the tiller easily, making it simpler to maneuver and providing excellent soil turning capabilities. The rear-tine tiller design is particularly beneficial for breaking new ground and turning compacted soil, ensuring an improved planting environment.

User comfort and ease of operation are also focal points of the Troy-Bilt 030245. The tiller comes with ergonomic handlebars that reduce fatigue during extended use. The adjustable handle design allows for customization to suit the user's height, enhancing control and comfort. Additionally, the heavy-duty, self-propelled tines facilitate movement through tough soil, reducing the physical strain on the operator.

The durable construction of the Troy-Bilt 030245 ensures longevity and reliable performance in various soil types. The reinforced steel frame and high-performance tines are built to withstand rigorous gardening tasks, making this tiller a long-term investment for any garden enthusiast.

In summary, the Troy-Bilt 030245 is a powerful and versatile tiller that combines advanced features and technologies aimed at enhancing the gardening experience. Its reliable engine, adjustable tilling width and depth, innovative tilling technology, and ergonomic design make it an excellent choice for gardeners seeking efficiency and effectiveness in their soil preparation tasks.
Top Page Image Contents