Operating Tips, Transporting the Log Splitter

Horizontal Position

•Pull the vertical beam lock out and rotate it down. See Figure 7. Pivot beam to the horizontal position. The beam will lock automatically in horizontal position.

•Stand behind the reservoir tank to operate control handle and to stabilize the log. See Figure 8B.

Operating Tips

Always:

1.	Use clean fluid and check fluid level regularly.
2.	Use Dexron III Automatic Transmission Fluid or
	10W AW hydraulic fluid.
3.	Use a filter (clean or replace regularly)
4.	Use a breather cap on fluid reservoir.
5.	Make sure pump is mounted and aligned properly.
6.	Use a flexible “spider” type coupling between
	engine and pump drive shafts.
7.	Keep hoses clear and unblocked.

WARNING: Always use the log splitter in the vertical position when splitting heavy logs.

•Pivot beam lock down to release the beam. Carefully pull back on beam and lower it to the horizontal position.The horizontal beam lock will lock automatically. See Figure 7.

Transporting the Log Splitter

IMPORTANT: Always turn fuel valve to OFF position before transporting the log splitter.

•Lower the beam to its horizontal position. Make certain the beam is locked securely with the horizontal beam lock.

•Remove spring clip and clevis pin from jack stand.

•Support the tongue and pivot the jack stand up against the tongue. See Figure 9.

8. Bleed air out of hoses before operating.

Tongue

Clevis Pin

9.	Flush and clean hydraulic system before restarting
	after servicing.
10.	Use “pipe dope” on all hydraulic fittings.
11.	Allow time for warm-up before splitting wood.
12.	Prime the pump before initial start-up by turning
	over the engine with spark plug disconnected.
13.	Split wood along the grain (lengthwise) only.

Never:

1.	Use when fluid is below 20° F or above 150° F.
2.	Use a solid engine /pump coupling.
3.	Operate through relief valve for long.
4.	Attempt to adjust unloading or relief valve settings

Assembly

Jack Stand

Spring

Clip

	without pressure gauges.
5.	Operate with air in hydraulic system.
6.	Use teflon tape on hydraulic fittings.
7.	Attempt to cut wood across the grain.

Raising and Lowering Beam

•Use control handle to run wedge up and down beam 6 to 8 times to circulate the hydraulic fluid, which will warm and thin the fluid.

•Place log splitter on a firm, level surface.

•To raise the beam for vertical operation: Pull out the vertical beam lock on the tongue.

•Pivot beam lock down to release the beam.

•Move the beam to the vertical position. Secure it with the beam lock on the reservoir tank assembly.

•To lower the beam: Pull out the horizontal beam lock on the reservoir tank.

Figure 9

•Secure with the spring clip and clevis pin previously removed. See Figure 9.

•Attach coupler hitch to a class I or higher 1-7/8” ball on a towing vehicle; latch securely.

a.If coupler hitch does not fit on ball: Turn adjustment nut one turn counter-clockwise.

b.If coupler hitch is too loose on ball: Turn adjustment nut one turn clockwise.

•Connect the safety chains to the towing vehicle.

•Plug in the tail lights to the tail light connector on the tow vehicle.

WARNING: Do not tow faster than 45mph and check local, state, and federal requirements before towing on any public road.

NOTE: Use caution when backing up. It is recommended to use a spotter outside the vehicle.

LS275 specifications

The Troy-Bilt LS275 is a versatile and efficient rear-tine tiller designed to make gardening and landscaping tasks more manageable. This machine is particularly suited for homeowners with larger gardens who require reliable tilling and soil preparation capabilities.

One of the standout features of the LS275 is its powerful engine. Equipped with a 208cc OHV engine, this tiller offers ample power for breaking up tough soil, ensuring that you can tackle even the most challenging garden plots. Its reliable starting system allows users to get to work quickly, minimizing downtime.

A key aspect of the LS275 is its rear-tine design, which provides stability and allows for deeper tilling. This configuration offers improved control and maneuverability, particularly in tight spaces or when working in uneven terrain. The tilling width of 18 inches is ideal for typical garden sizes, while the adjustable tilling depth, ranging from 3 to 7 inches, enables users to customize the tilling process according to specific garden needs.

The Troy-Bilt LS275 is designed with user comfort and convenience in mind. Its adjustable handle can be tailored to suit users of varying heights, reducing strain during extended use. The lightweight construction, combined with the counter-rotating tines, ensures that the tiller can glide through the soil with ease, allowing for efficient operation and less fatigue.

The tines themselves are made from durable materials that are built to withstand the rigors of tough soil conditions. The counter-rotating action of the tines helps to break up hard-packed soil and incorporates organic matter effectively, contributing to healthier garden beds.

Another notable feature of the LS275 is its robust 6-inch rear wheels. These provide excellent traction and stability, making it easier to maneuver across different terrains while maintaining control over tilling depth and width.

Safety is also a priority with the LS275, featuring an easy-access throttle control and a safety guard that helps protect the user from debris.

Overall, the Troy-Bilt LS275 stands out for its power, efficiency, and user-friendly features, making it a great choice for both novice and experienced gardeners looking to optimize their soil preparation efforts. With its combination of reliability and performance, this tiller can help transform any garden into a thriving, productive space.