White Outdoor LT-542K, LT-942K, LT-946K manual Cutting Blades, Charging, Jump Starting, Cleaning

Page 22

•Always keep the battery cables and terminals clean and free of corrosive build-up.

•After cleaning the battery and terminals, apply a light coat of petroleum jelly or grease to both terminals.

•Always keep the rubber boot positioned over the positive terminal to prevent shorting.

IMPORTANT: If removing the battery for any reason, disconnect the NEGATIVE (Black) wire from it’s terminal first, followed by the POSITIVE (Red) wire. When re-installing the battery, always connect the POSITIVE (Red) wire its terminal first, followed by the NEGATIVE (Black) wire. Be certain that the wires are connected to the correct terminals; reversing them could change the polarity and result in damage to your engine’s alternating system.

Charging

If the tractor has not been put into use for an extended period of time, charge the battery with an automotive- type 12-volt charger for a minimum of one hour at six amps.

WARNING: Batteries give off an explosive gas while charging. Charge battery in a well ventilated area and keep away from an open flame or pilot light as on a water heater, space heater, furnace, clothes dryer or other gas appliances.

Jump Starting

WARNING: When removing or installing the battery, follow these instructions to prevent the screwdriver from shorting against the frame.

IMPORTANT: Never jump your tractor’s dead battery with the battery of a running vehicle.

•Connect end of one jumper cable to the positive terminal of the good battery, then the other end to the positive terminal of the dead battery.

•Connect the other jumper cable to the negative terminal of the good battery, then to the frame of the unit with the dead battery.

WARNING: Failure to use this procedure could cause sparking, and the gas in either battery could explode.

Cleaning

Clean the battery by removing it from the tractor and washing with a baking soda and water solution. If necessary, scrape the battery terminals with a wire brush to remove deposits. Coat terminals and exposed wiring with grease or petroleum jelly to prevent corrosion.

Hex Flange Nut

Wood Block

Spindle Assembly

Figure 19

Battery Failures

Some common causes for battery failure are:

•

incorrect initial activation

•

undercharging

•

overcharging

•

corroded connections

•

freezing

 

 

These failures are NOT covered by your tractor’s warranty.

Cutting Blades

WARNING: Be sure to shut the engine off, remove ignition key, disconnect the spark plug wire(s) and ground against the engine to prevent unintended starting before removing the cutting blade(s) for sharpening or replacement. Protect your hands by using heavy gloves or a rag to grasp the cutting blade.

WARNING: Periodically inspect the blade spindles for cracks or damage, especially if you strike a foreign object. Replace immediately if damaged.

The blades may be removed as follows.

•Remove the deck from beneath the tractor, (refer to Cutting Deck Removal on page 21) then gently flip the deck over to expose its underside.

•Place a block of wood between the center deck housing baffle and the cutting blade to act as a stabilizer. See Figure 19.

•Use a 15/16" wrench to remove the hex flange nut that secures the blade to the spindle assembly. See Figure 19.

•To properly sharpen the cutting blades, remove equal amounts of metal from both ends of the blades along the cutting edges, parallel to the trailing edge, at a 25° to 30° angle. See Figure 20.

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Operator’s Manual Table of Contents Important Safe Operation Practices General OperationSlope Operation Towing Safety labels found on your unit Slope Gauge Gas and Oil Fill-up Attaching the Battery CablesShipping Brace Removal Attaching the Steering Wheel Quick Adjustment SeatKnob Adjustment Seat Attaching the SeatChoke Control Know Your Lawn TractorThrottle Control Lever Brake PedalThrottle Lever Systems Indicator Monitor Ignition Switch ModuleDrive Pedal Manual PTO Blade Engage Lever Seat Adjustment LeverElectric PTO Blade Engage Knob Deck Lift LeverOperating Your Lawn Tractor Safety Interlock SwitchesReverse Caution Mode Shift LeverEngaging the Parking Brake Setting the Cutting HeightStarting the Engine Driving the Tractor Setting the Cruise ControlStopping the Engine Driving On SlopesMulching Using the Deck Lift LeverMowing HeadlightsLeveling the Deck Making AdjustmentsParking Brake Adjustment Front To RearQuick-Adjust Seat if so equipped Seat AdjustmentSteering Adjustment Knob Adjustment Seat if so equippedEngine Cleaning the Engine and DeckMaintaining Your Lawn Tractor LubricationCutting Deck Removal ServiceBattery TiresCutting Blades CleaningBattery Failures ChargingInch and 46-inch Decks with Manual PTO FusesChanging the Deck Belt & PTO Belt Inch and 46-inch Decks with Electric PTOChanging the Transmission Drive Belts v$ECKAttachments & Accessories OFF-SEASON StorageTroubleshooting Trouble Possible Causes Corrective ActionMANUFACTURER’S Limited Warranty

LT-542K, LT-942K, LT-946K specifications

The White Outdoor LT-542K, LT-942K, and LT-946K are robust riding lawn mowers known for their reliability and performance, making them popular choices among homeowners and landscapers alike. Each model is designed to tackle large yards with ease, providing an efficient and effective mowing experience.

The LT-542K model features a 42-inch cutting deck, allowing users to cover more ground in less time. It is powered by a reliable Kohler engine, which delivers ample power to handle various mowing conditions. The LT-542K also comes equipped with a hydrostatic transmission that offers smooth, effortless operation, allowing users to adjust their speed without the need for shifting gears. This feature is particularly useful for navigating tight spaces and uneven terrain.

Moving on to the LT-942K, this model takes performance a step further with a larger 48-inch cutting deck. This increased width allows for quicker mowing over larger areas, reducing overall mowing time. The LT-942K is also equipped with a powerful Briggs & Stratton engine, renowned for its durability and efficiency. The automatic transmission provides an easier driving experience, while the comfortable seating and ergonomic controls ensure that users can operate the mower for extended periods without discomfort.

The LT-946K model is the flagship of these series, boasting a 46-inch cutting deck that strikes a balance between maneuverability and cutting capacity. This model further enhances the mowing experience with its advanced features, including a mulching capability that allows users to finely chop grass clippings, returning nutrients back into the lawn. The LT-946K is designed with a heavy-duty steel frame to withstand rigorous usage, ensuring longevity and robustness.

All three models share essential characteristics such as easy cutting height adjustment, allowing users to customize their lawn’s finish. They also feature reliable, efficient engines that can easily tackle tough mowing conditions. In addition, their intuitive controls and user-friendly designs make them accessible for both seasoned operators and those new to riding mowers.

In summary, the White Outdoor LT-542K, LT-942K, and LT-946K offer a combination of power, durability, and ease of use. Whether for residential use or professional landscaping, these mowers deliver performance that meets the needs of various users, proving to be valuable assets in lawn care maintenance.
Top Page Image Contents