Woods Equipment RCC42 manual Transportation, Maintenance

Page 8

SAFETY RULES

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

(Safety Rules continued from previous page)

Full chain, rubber, or steel band shielding must be installed when operating in populated areas or other areas where thrown objects could injure peo- ple or damage property.

•If this machine is not equipped with full chain, rubber, or steel band shielding, operation must be stopped when anyone comes within 300 feet (92 m).

•This shielding is designed to reduce the risk of thrown objects. The mower deck and protec- tive devices cannot prevent all objects from escaping the blade enclosure in every mowing condition. It is possible for objects to ricochet and escape, traveling as much as 300 feet (92 m).

Never direct discharge toward people, animals, or property.

Do not operate or transport equipment while under the influence of alcohol or drugs.

Operate only in daylight or good artificial light.

Keep hands, feet, hair, and clothing away from equipment while engine is running. Stay clear of all moving parts.

Always comply with all state and local lighting and marking requirements.

Never allow riders on power unit or attachment.

Power unit must be equipped with ROPS or ROPS cab and seat belt. Keep seat belt securely fastened. Falling off power unit can result in death from being run over or crushed. Keep foldable ROPS systems in “locked up” position at all times.

Always sit in power unit seat when operating controls or starting engine. Securely fasten seat belt, place transmission in neutral, engage brake, and ensure all other controls are disengaged before starting power unit engine.

Operate tractor PTO at 540 RPM. Do not exceed.

Connect PTO driveline directly to power unit PTO shaft. Never use adapter sleeves or adapter shafts. Adapters can cause driveline failures due to incorrect spline or incorrect operating length and can result in personal injury or death.

Look down and to the rear and make sure area is clear before operating in reverse.

Do not operate or transport on steep slopes.

Do not stop, start, or change directions sud- denly on slopes.

Use extreme care and reduce ground speed on slopes and rough terrain.

Watch for hidden hazards on the terrain during operation.

Stop power unit and equipment immediately upon striking an obstruction. Turn off engine, remove key, inspect, and repair any damage before resuming operation.

Leak down or failure of mechanical or hydraulic system can cause equipment to drop.

TRANSPORTATION

Always comply with all state and local lighting and marking requirements.

Never allow riders on power unit or attachment.

Do not operate PTO during transport.

Watch for hidden hazards on the terrain.

A minimum 20% of tractor and equipment weight must be on the tractor front wheels when attachments are in transport position. Without this weight, front tractor wheels could raise up result- ing in loss of steering. The weight may be attained with front wheel weights, ballast in tires or front tractor weights. Weigh the tractor and equipment. Do not estimate.

Power unit must be equipped with ROPS or ROPS cab and seat belt. Keep seat belt securely fastened. Falling off power unit can result in death from being run over or crushed. Keep foldable ROPS system in “locked up” position at all times.

Do not operate or transport on steep slopes.

Do not operate or transport equipment while under the influence of alcohol or drugs.

MAINTENANCE

Before performing any service or maintenance, disconnect driveline from tractor PTO.

Before working underneath, disconnect drive- line, raise cutter, and block cutter securely. Hydraulic system leak down and failure of mechan- ical or hydraulic system can cause equipment to drop.

Do not modify or alter or permit anyone else to modify or alter the equipment or any of its compo- nents in any way.

Always wear relatively tight and belted clothing to avoid entanglement in moving parts. Wear sturdy, rough-soled work shoes and protective

8 Safety

RCC42 (Rev. 7/29/2005)

 

 

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Rotary Cutters Introduction To the DealerTable of Contents LEA EL InstructivoSpecifications General InformationFree Mower Safety Video SafetyTraining Package for Rotary Mowers/Cutters-English Training Package for Rotary Mowers/Cutters-English/SpanishSafety Rules TrainingPreparation OperationMaintenance TransportationStorage Safety & Instructional Decals Replace Immediately If DamagedKeep Away Attaching Cutter to Tractor OperationOperation Installation Removal of Driveline Tractor PTO Cutting Height AdjustmentTOP Link Adjustment Figure ShreddingQuick Hitch Attachment Figure Operating TechniquePRE-OPERATION Check List Owners Responsibility Owner Service Owner ServiceBlocking Method Lubrication InformationServicing Blades Removing BladesInstalling Blades Figure Sharpening BladesComer WalterscheidWalterscheid ModelRepairing Shielding CleaningReplacing Shear Bolts After Each UseMowing Conditions TroubleshootingTroubleshooting Dealer Service Dealer ServiceGearbox Maintenance Seal Replacement FigureSeal Repair On Flat TOP, Gearbox S/N Before Gearbox Repair On Flat TOP, Gearbox S/N BeforeReinstall Gearbox Reassemble GearboxGearbox Assembly Flat Top Cast/Crown Top Gearbox Assembly Reassemble Gearbox Cast Top Crossbar Removal Crossbar RemovalUniversal Joint Repair Crossbar InstallationJoint Disassembly Joint Assembly Dealer Service Dealer SET-UP Instructions AssemblyAssembly Instructions Install Slip Clutch Driveline Driveline to gearboxOptional Slip Clutch Driveline Assembly Shorten Driveline for Specific TractorInstall Chain Shielding Optional Fill Gearbox OilDealer Check Lists Dealer Check ListsPRE-DELIVERY Check List Delivery Check ListRotary Cutters PartsRCC42 Assembly RCC42 Parts List Part QTY DescriptionGearbox Assembly Flat TOP Gearbox Assembly Parts List Flat TOP REF Part QTY DescriptionGearbox Assembly CAST/CROWN TOP RCC42 Shear Bolt Driveline TWO Lobe Walterscheid RCC42 Standard Driveline Comer RCC42 Slip Clutch Driveline Optional Walterscheid RCC42 Slip Clutch Driveline Optional Comer Front & Rear Chain Shielding Optional Bolt Torque Chart SAE Series Torque ChartAppendix Metric SeriesBolt Size Chart AbbreviationsIndex IndexWarranty Rev /23/2005

RCC42 specifications

Woods Equipment has long been recognized for its commitment to quality and performance in the field of agricultural and landscape equipment. One standout product that reflects this dedication is the Woods RCC42. This rotary cutter, designed for robust performance, is particularly suitable for handling various mowing tasks, making it a favorite among professionals and avid gardeners alike.

At the heart of the Woods RCC42 is its durable construction. Made from high-quality materials, this rotary cutter is built to withstand the rigors of heavy use. Its heavy-duty frame ensures stability and longevity, ideal for tackling tough brush and dense vegetation. The RCC42 features a wide cutting width of 42 inches, allowing users to cover more ground quickly while ensuring a clean and even cut.

One of the key features of the Woods RCC42 is its superior cutting capability, which comes from its specially designed blades. The rotary cutter is equipped with sharp, high-carbon steel blades that can easily slice through even the thickest grass and brush. The blades are positioned in a way that optimizes cutting efficiency, ensuring that the mower leaves behind a finely cut finish, whether you are mowing a field or maintaining a garden.

In terms of technology, the Woods RCC42 is designed with user-friendliness in mind. The cutter is engineered to be easily attached to a variety of compact tractors, making it a versatile option for many users. Its adjustable cutting height feature allows operators to set the cutter to their desired height, accommodating different mowing conditions and vegetation types. Additionally, the RCC42 operates smoothly and quietly, making it a pleasant option for those who wish to work for extended periods without excessive noise.

Safety is another paramount consideration with the Woods RCC42. The cutter features a shielded design that provides protection to the operator while preventing debris from being ejected during operation. This thoughtful design element minimizes risks, making it a safer choice for users of all experience levels.

Overall, the Woods RCC42 rotary cutter exemplifies a balance of durability, efficiency, and user-friendly technology. Whether you are a professional landscaper or a homeowner looking to maintain your property, the RCC42 offers the reliability and performance needed to tackle even the toughest mowing jobs with ease. With its proven track record, the Woods RCC42 continues to be a benchmark in rotary cutting equipment, enhancing productivity and ensuring satisfaction for those who rely on it.
Top Page Image Contents