Woods Equipment RDC54, RD72 Assembly Instructions, Dealer SET-UP Instructions, Uncrate Mower

Page 27

ASSEMBLY INSTRUCTIONS

DEALER SET-UP INSTRUCTIONS

Assembly of this mower is the responsibility of the Woods dealer. It should be delivered to the owner com- pletely assembled, lubricated, and adjusted for normal cutting conditions.

Complete Dealer Check Lists on page 31 when you have completed the assembly.

The mower is shipped ￿￿￿￿￿￿￿partially assembled. Assembly will be easier if components are aligned and loosely assembled before tightening hardware. Recommended torque values for hardware are located on page 43.

Select a suitable working area. Open parts boxes and lay out parts and hardware to make location easy. Refer to illustrations, accompanying text, parts lists and exploded view drawings.

„Before working underneath, carefully read Oper- ator’s Manual instructions, disconnect driveline, raise mower, securely block up all corners with jackstands, and check stability. Secure blocking prevents equipment from dropping due to hydrau- lic leak down, hydraulic system failures, or mechanical component failures.

CAUTION

„Always wear relatively tight and belted clothing to avoid entanglement in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head; and respirator or filter mask where appropriate.

Uncrate Mower

1.Remove sides and top of mower shipping crate.

2.Remove lag screws and brackets that secure mower to crate base.

3.Remove driveshaft wired to mower deck.

Install A-Frame Arms

1.Loosen lock nuts (52) at lower hitch point and install A-frame arms (13) as shown.

2.Tighten nut securely.

3.Repeat for opposite side.

CD6497

13.A-frame arms

14.Rear offset link arms

15.Top link U-bracket

16.Sleeve 1-1/4 x 1-3/4 x 2-3/4

25.Sleeve 5/8 x 1 x 7/16

51.1/2 NC Flanged lock nut

52.5/8 NC Flanged lock nut

54.5/8 Standard flat washer

55.1/2 NC x 1-1/4 HHCS GR5

56.5/8 NC x 2-1/2 HHCS GR5

Figure 23. A-Frame Arms Installed

(Rev. 1/13/2006)

MAN0260 (8/6/2004)

Assembly 27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Heritage Rear Discharge Mower To the Dealer IntroductionLEA EL Instructivo Table of ContentsSpecifications General InformationRD60 RD72 Preparation SafetySafety Rules TrainingTransportation MaintenanceStorage Safety & Instructional Decals 11 20106 Rear Reflector RD60 & RD72 OnlySerial Number Plate Be Careful Replace Immediately If DamagedOperation OperationAttach Mower to Tractor Tractor Top Link Adjustment Adjust Cutting HeightRDC54 Only Front Caster Wheel Interference Check Front Roller OptionalOperating Technique Owner PRE-OPERATION Check List Removing Mower from Tractor StorageLubrication Information Owner ServiceOwner Service Blocking MethodService Belt Replace BeltDescription Frequency Install Belt Sharpen BladesRefer to Figure After Each Use Install BladesCleaning Chain ShieldingMowing Conditions TroubleshootingBelt Conditions Trouble ShootingDisassemble Spindle Dealer ServiceBlade Spindle Repair Remove SpindleAssemble Spindle Seal ReplacementSeal Installation Gearbox RepairSeal Installation Disassemble Gearbox Vertical Shaft Seal ReplacementHorizontal Shaft Seal Replacement Remove Gearbox from MowerAll Models Install GearboxInstall Drive Sheave RD60 & RD72Universal Joint Repair Joint DisassemblyJoint Assembly Dealer SET-UP Instructions AssemblyAssembly Instructions Install A-Frame ArmsInstall Chain Shielding Optional Install Rear Offset Link ArmsInstall Top Link Install DriveshaftChain Shield Installed RDC54 Only Install Quick Hitch Kit Optional RD60 & RD72 OnlyFront Roller Installation Install Front Roller OptionalDealer Delivery Check List Dealer Check ListsDealer Check Lists Dealer PRE-DELIVERY Check ListDealer Check Lists Parts RDC54RDC54 Part RD60 Part RD72 Part QTY Description RDC54, RD60 & RD72 Main Frame AssemblyPart Description QTY Description Part RDC54, RD60 & RD72 Gearbox AssemblyRDC54 QTY QTY Description RDC54Part QTY Description RDC54 Driveline Assembly ComerRD60 & RD 72 Driveline Assembly Comer 40776 Bearing ring, guard RDC54, RD60 & RD72 Driveshaft Walterscheid TWO-LOBE ShaftRDC54, RD60, RD72 Belt Guide Optional RDC54, RD60 & RD72 Blade & Spindle AssemblyRD60 & RD72 Rear Chain Shielding Assembly Optional RDC54 Rear Chain Shield Assembly OptionalREF Part QTY Description RD60 & RD72 Quick Hitch KIT Optional RDC54, RD60 & RD72 Front Roller Assembly OptionalMetric Series Bolt Torque ChartSAE Series Torque Chart AppendixAbbreviations Bolt Size ChartIndex IndexWarranty Rev /23/2005 MAN0260

RD60, RD72, RDC54 specifications

Woods Equipment is renowned for its innovative and efficient landscaping solutions, and the RD series of rotary cutters exemplifies this reputation. The RD60, RDC54, and RD72 models are designed to cater to varying needs in land management, providing robust performance and ease of use.

The RD60 model stands out for its impressive cutting width of 60 inches, making it an ideal choice for commercial and residential applications. Its heavy-duty construction ensures longevity, with a rugged deck design that can withstand challenging terrains. The RD60 features a slip clutch protection system that prevents damage to the cutter during operation by absorbing shock loads. Additionally, its adjustable skids allow for varied cutting heights, making it versatile for different types of vegetation.

RDC54, while slightly smaller with a cutting width of 54 inches, is designed with a focus on efficiency and maneuverability. Its compact build makes it perfect for smaller properties or tight spaces. The RDC54 boasts a quick-attach mounting system, enabling users to easily connect and disconnect the cutter from their tractor. Users can also appreciate the innovative dual-blade design that enhances cutting performance, resulting in a finer mulch for improved decomposition when tackling thicker grass and brush.

On the other hand, the RD72 takes productivity to the next level with its 72-inch cutting width. This model is particularly favored by professionals looking to cover large areas quickly. Equipped with an advanced drive system, the RD72 delivers consistent power to its blades, ensuring clean cuts even in tough conditions. The model features a robust frame and reinforced side panels, making it suitable for heavy-duty applications. Furthermore, its quick-adjustment feature allows operators to change the cutting height smoothly and efficiently, maximizing versatility.

All models in the RD series incorporate cutting-edge technology, such as optimized blade design and improved airflow, which contributes to a cleaner and more efficient cut. Durability is a common theme across the series, with high-quality materials used throughout the construction ensuring these rotary cutters can handle the rigors of daily use.

In conclusion, Woods Equipment's RD60, RDC54, and RD72 rotary cutters offer a blend of durability, efficiency, and advanced features, catering to the diverse needs of landscape professionals and property owners alike. Whether the job requires finesse or brute force, there's an RD model built to deliver results.
Top Page Image Contents