Woods Equipment RD60, RDC54, RD72 manual Safety Rules, Training, Preparation, Operation

Page 5

SAFETY RULES

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Safety is a primary concern in the design and manufacture of our products. Unfortunately, our efforts to provide safe equipment can be wiped out by an operator’s single careless act.

In addition to the design and configuration of equipment, hazard control and accident preven- tion are dependent upon the awareness, concern, judgement, and proper training of personnel involved in the operation, transport, maintenance and storage of equipment.

It has been said “The best safety device is an informed, careful operator.” We ask you to be that kind of operator.

TRAINING

„Safety instructions are important! Read all attachment and power unit manuals; follow all safety rules and safety decal information. (Replace- ment manuals and safety decals are available from your dealer. To locate your nearest dealer, check the Dealer Locator at www.WoodsEquipment.com, or in the United States and Canada call 1-800-319- 6637.) Failure to follow instructions or safety rules can result in serious injury or death.

„Know your controls and how to stop engine and attachment quickly in an emergency.

„If you do not understand any part of this manual and need assistance, see your dealer.

„Operators must be instructed in and be capable of the safe operation of the equipment, its attach- ments, and all controls. Do not allow anyone to operate this equipment without proper instruc- tions.

„Never allow children or untrained persons to operate equipment.

PREPARATION

„Check that all hardware is properly installed. Always tighten to torque chart specifications unless instructed otherwise in this manual.

„Always wear relatively tight and belted clothing to avoid entanglement in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head; and respirator or filter mask where appropriate.

„Make sure attachment is properly secured, adjusted, and in good operating condition.

„Make sure spring-activated locking pin or collar slides freely and is seated firmly in tractor PTO spline groove.

„Make sure driveline shield tether chains are attached to the tractor and equipment as shown in this manual. Replace if damaged or broken. Check that driveline guards rotate freely on driveline before putting equipment into service.

„Before starting power unit, check all equipment driveline guards for damage. Replace any damaged guards. Make sure all guards rotate freely on all drivelines. If guards do not rotate freely on drive- lines, repair and replace bearings before putting equipment into service.

„Power unit must be equipped with ROPS or ROPS cab and seat belt. Keep seat belt securely fastened. Falling off power unit can result in death from being run over or crushed. Keep foldable ROPS systems in “locked up” position at all times.

„Power unit must be equipped with ROPS or ROPS cab and seat belt. Keep seat belt securely fastened. Falling off power unit can result in death from being run over or crushed. Keep foldable ROPS systems in “locked up” position at all times.

„Remove accumulated debris from this equip- ment, power unit, and engine to avoid fire hazard.

„Make sure all safety decals are installed. Replace if damaged. (See Safety Decals section for location.)

„Make sure shields and guards are properly installed and in good condition. Replace if dam- aged.

„A minimum 25% of tractor and equipment weight must be on the tractor front wheels when attachments are in transport position. Without this weight, tractor could tip over, causing personal injury or death. The weight may be attained with a loader. Weigh the tractor and equipment. Do not estimate.

OPERATION

„Full chain shielding, designed to reduce the possibility of thrown objects, must be installed when operating in populated areas or other areas where thrown objects could injure people or dam- age property. If this machine is not equipped with full chain shielding, operation must be stopped when anyone comes within several hundred feet.

RD 54/60/72 (Rev. 1/12/2007)

Safety 5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Heritage Rear Discharge Mower To the Dealer IntroductionLEA EL Instructivo Table of ContentsRD60 RD72 SpecificationsGeneral Information Safety Rules SafetyTraining PreparationTransportation MaintenanceStorage Serial Number Plate Safety & Instructional Decals11 20106 Rear Reflector RD60 & RD72 Only Be Careful Replace Immediately If DamagedAttach Mower to Tractor OperationOperation RDC54 Only Tractor Top Link AdjustmentAdjust Cutting Height Operating Technique Front Caster Wheel Interference CheckFront Roller Optional Owner PRE-OPERATION Check List Removing Mower from Tractor StorageOwner Service Owner ServiceBlocking Method Lubrication InformationDescription Frequency Service BeltReplace Belt Refer to Figure Install BeltSharpen Blades Cleaning Install BladesChain Shielding After Each UseMowing Conditions TroubleshootingBelt Conditions Trouble ShootingBlade Spindle Repair Dealer ServiceRemove Spindle Disassemble SpindleSeal Installation Seal ReplacementGearbox Repair Assemble SpindleSeal Installation Horizontal Shaft Seal Replacement Vertical Shaft Seal ReplacementRemove Gearbox from Mower Disassemble GearboxInstall Drive Sheave Install GearboxRD60 & RD72 All ModelsUniversal Joint Repair Joint DisassemblyJoint Assembly Assembly Instructions AssemblyInstall A-Frame Arms Dealer SET-UP InstructionsInstall Top Link Install Rear Offset Link ArmsInstall Driveshaft Install Chain Shielding OptionalChain Shield Installed RDC54 Only Install Quick Hitch Kit Optional RD60 & RD72 OnlyFront Roller Installation Install Front Roller OptionalDealer Check Lists Dealer Check ListsDealer PRE-DELIVERY Check List Dealer Delivery Check ListDealer Check Lists Parts RDC54RDC54 Part RD60 Part RD72 Part QTY Description RDC54, RD60 & RD72 Main Frame AssemblyPart Description RDC54 QTY RDC54, RD60 & RD72 Gearbox AssemblyQTY Description RDC54 QTY Description PartPart QTY Description RDC54 Driveline Assembly ComerRD60 & RD 72 Driveline Assembly Comer 40776 Bearing ring, guard RDC54, RD60 & RD72 Driveshaft Walterscheid TWO-LOBE ShaftRDC54, RD60, RD72 Belt Guide Optional RDC54, RD60 & RD72 Blade & Spindle AssemblyREF Part QTY Description RD60 & RD72 Rear Chain Shielding Assembly OptionalRDC54 Rear Chain Shield Assembly Optional RD60 & RD72 Quick Hitch KIT Optional RDC54, RD60 & RD72 Front Roller Assembly OptionalSAE Series Torque Chart Bolt Torque ChartAppendix Metric SeriesAbbreviations Bolt Size ChartIndex IndexWarranty Rev /23/2005 MAN0260

RD60, RD72, RDC54 specifications

Woods Equipment is renowned for its innovative and efficient landscaping solutions, and the RD series of rotary cutters exemplifies this reputation. The RD60, RDC54, and RD72 models are designed to cater to varying needs in land management, providing robust performance and ease of use.

The RD60 model stands out for its impressive cutting width of 60 inches, making it an ideal choice for commercial and residential applications. Its heavy-duty construction ensures longevity, with a rugged deck design that can withstand challenging terrains. The RD60 features a slip clutch protection system that prevents damage to the cutter during operation by absorbing shock loads. Additionally, its adjustable skids allow for varied cutting heights, making it versatile for different types of vegetation.

RDC54, while slightly smaller with a cutting width of 54 inches, is designed with a focus on efficiency and maneuverability. Its compact build makes it perfect for smaller properties or tight spaces. The RDC54 boasts a quick-attach mounting system, enabling users to easily connect and disconnect the cutter from their tractor. Users can also appreciate the innovative dual-blade design that enhances cutting performance, resulting in a finer mulch for improved decomposition when tackling thicker grass and brush.

On the other hand, the RD72 takes productivity to the next level with its 72-inch cutting width. This model is particularly favored by professionals looking to cover large areas quickly. Equipped with an advanced drive system, the RD72 delivers consistent power to its blades, ensuring clean cuts even in tough conditions. The model features a robust frame and reinforced side panels, making it suitable for heavy-duty applications. Furthermore, its quick-adjustment feature allows operators to change the cutting height smoothly and efficiently, maximizing versatility.

All models in the RD series incorporate cutting-edge technology, such as optimized blade design and improved airflow, which contributes to a cleaner and more efficient cut. Durability is a common theme across the series, with high-quality materials used throughout the construction ensuring these rotary cutters can handle the rigors of daily use.

In conclusion, Woods Equipment's RD60, RDC54, and RD72 rotary cutters offer a blend of durability, efficiency, and advanced features, catering to the diverse needs of landscape professionals and property owners alike. Whether the job requires finesse or brute force, there's an RD model built to deliver results.
Top Page Image Contents