Woods Equipment RD60, RDC54, RD72 manual Install Blades, Chain Shielding, Cleaning, After Each Use

Page 17

Figure 10. Blade Balancing

1.Follow original sharpening pattern.

2.Do not sharpen blade to a razor edge, but leave approximately 1/64" blunt edge.

3.Do not sharpen back side of blade.

4.Sharpen both cutting edges equally to keep blade balanced. Balance blade using the method shown in Figure 10.

Install Blades

CAUTION

„Your dealer can supply genuine replacement blades. Substitute blades may not meet original equipment specifications and may be dangerous.

IMPORTANT

■When installing blade, the lift of the blade must be toward the spindle blade housing as shown in Figure 11. Torque bolt (1) into shaft assembly to 100 lbs-ft.

1.Place blade over blade pilot on the bottom of the shaft assembly.

2.Place bell washer (2) over blade and insert blade bolt (1). Torque blade bolt to 100 lbs-ft.

1.5/8 NF x 2 Cap screw GR5

2.Bell washer, 5/8 x 1-3/4 x .075

Figure 11. Blade and Spindle Assembly

Chain Shielding

„Full chain shielding, designed to reduce the possibility of thrown objects, must be installed when operating in populated areas or other areas where thrown objects could injure people or dam- age property. If this machine is not equipped with full chain shielding, operation must be stopped when anyone comes within several hundred feet.

Check that chain shielding is in good condition and replace any damaged chain links.

CLEANING

After Each Use

●Remove large debris such as clumps of dirt, grass, crop residue, etc. from machine.

●Inspect machine and replace worn or damaged parts.

●Replace any safety decals that are missing or not readable (supplied free by your Woods dealer).

Periodically or Before Extended Storage

●Clean large debris such as clumps of dirt, grass, crop residue, etc. from machine.

●Remove the remainder using a low-pressure water spray.

1.Be careful when spraying near scratched or torn safety decals or near edges of decals as water spray can peel decal off surface.

2.Be careful when spraying near chipped or scratched paint as water spray can lift paint.

3.If a pressure washer is used, follow the advice of the pressure washer manufacturer.

●Inspect machine and replace worn or damaged parts.

●Sand down scratches and the edges of areas of missing paint and coat with Woods spray paint of matching color (purchase from your Woods dealer).

●Replace any safety decals that are missing or not readable (supplied free by your Woods dealer). See Safety Decals section for location drawing.

MAN0260 (Rev. 1/12/2007)

Owner Service 17

 

 

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Heritage Rear Discharge Mower To the Dealer IntroductionLEA EL Instructivo Table of ContentsRD60 RD72 SpecificationsGeneral Information Safety Rules SafetyTraining PreparationTransportation MaintenanceStorage Serial Number Plate Safety & Instructional Decals11 20106 Rear Reflector RD60 & RD72 Only Be Careful Replace Immediately If DamagedAttach Mower to Tractor OperationOperation RDC54 Only Tractor Top Link AdjustmentAdjust Cutting Height Operating Technique Front Caster Wheel Interference CheckFront Roller Optional Owner PRE-OPERATION Check List Removing Mower from Tractor StorageOwner Service Owner ServiceBlocking Method Lubrication InformationDescription Frequency Service BeltReplace Belt Refer to Figure Install BeltSharpen Blades Cleaning Install BladesChain Shielding After Each UseMowing Conditions TroubleshootingBelt Conditions Trouble ShootingBlade Spindle Repair Dealer ServiceRemove Spindle Disassemble SpindleSeal Installation Seal ReplacementGearbox Repair Assemble SpindleSeal Installation Horizontal Shaft Seal Replacement Vertical Shaft Seal ReplacementRemove Gearbox from Mower Disassemble GearboxInstall Drive Sheave Install GearboxRD60 & RD72 All ModelsUniversal Joint Repair Joint DisassemblyJoint Assembly Assembly Instructions AssemblyInstall A-Frame Arms Dealer SET-UP InstructionsInstall Top Link Install Rear Offset Link ArmsInstall Driveshaft Install Chain Shielding OptionalChain Shield Installed RDC54 Only Install Quick Hitch Kit Optional RD60 & RD72 OnlyFront Roller Installation Install Front Roller OptionalDealer Check Lists Dealer Check ListsDealer PRE-DELIVERY Check List Dealer Delivery Check ListDealer Check Lists Parts RDC54RDC54 Part RD60 Part RD72 Part QTY Description RDC54, RD60 & RD72 Main Frame AssemblyPart Description RDC54 QTY RDC54, RD60 & RD72 Gearbox AssemblyQTY Description RDC54 QTY Description PartPart QTY Description RDC54 Driveline Assembly ComerRD60 & RD 72 Driveline Assembly Comer 40776 Bearing ring, guard RDC54, RD60 & RD72 Driveshaft Walterscheid TWO-LOBE ShaftRDC54, RD60, RD72 Belt Guide Optional RDC54, RD60 & RD72 Blade & Spindle AssemblyREF Part QTY Description RD60 & RD72 Rear Chain Shielding Assembly OptionalRDC54 Rear Chain Shield Assembly Optional RD60 & RD72 Quick Hitch KIT Optional RDC54, RD60 & RD72 Front Roller Assembly OptionalSAE Series Torque Chart Bolt Torque ChartAppendix Metric SeriesAbbreviations Bolt Size ChartIndex IndexWarranty Rev /23/2005 MAN0260

RD60, RD72, RDC54 specifications

Woods Equipment is renowned for its innovative and efficient landscaping solutions, and the RD series of rotary cutters exemplifies this reputation. The RD60, RDC54, and RD72 models are designed to cater to varying needs in land management, providing robust performance and ease of use.

The RD60 model stands out for its impressive cutting width of 60 inches, making it an ideal choice for commercial and residential applications. Its heavy-duty construction ensures longevity, with a rugged deck design that can withstand challenging terrains. The RD60 features a slip clutch protection system that prevents damage to the cutter during operation by absorbing shock loads. Additionally, its adjustable skids allow for varied cutting heights, making it versatile for different types of vegetation.

RDC54, while slightly smaller with a cutting width of 54 inches, is designed with a focus on efficiency and maneuverability. Its compact build makes it perfect for smaller properties or tight spaces. The RDC54 boasts a quick-attach mounting system, enabling users to easily connect and disconnect the cutter from their tractor. Users can also appreciate the innovative dual-blade design that enhances cutting performance, resulting in a finer mulch for improved decomposition when tackling thicker grass and brush.

On the other hand, the RD72 takes productivity to the next level with its 72-inch cutting width. This model is particularly favored by professionals looking to cover large areas quickly. Equipped with an advanced drive system, the RD72 delivers consistent power to its blades, ensuring clean cuts even in tough conditions. The model features a robust frame and reinforced side panels, making it suitable for heavy-duty applications. Furthermore, its quick-adjustment feature allows operators to change the cutting height smoothly and efficiently, maximizing versatility.

All models in the RD series incorporate cutting-edge technology, such as optimized blade design and improved airflow, which contributes to a cleaner and more efficient cut. Durability is a common theme across the series, with high-quality materials used throughout the construction ensuring these rotary cutters can handle the rigors of daily use.

In conclusion, Woods Equipment's RD60, RDC54, and RD72 rotary cutters offer a blend of durability, efficiency, and advanced features, catering to the diverse needs of landscape professionals and property owners alike. Whether the job requires finesse or brute force, there's an RD model built to deliver results.
Top Page Image Contents