Woods Equipment RDC54, RD72, RD60 manual Transportation, Maintenance

Page 6

SAFETY RULES

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

„Inspect and clear area of stones, branches, or other hard objects that might be thrown, causing injury or damage.

„Never direct discharge toward people, animals, or property.

„Keep bystanders away from equipment.

„Never go underneath equipment (lowered to the ground or raised) unless it is properly blocked and secured. Never place any part of the body under- neath equipment or between moveable parts even when the engine has been turned off. Hydraulic system leak down, hydraulic system failures, mechanical failures, or movement of control levers can cause equipment to drop or rotate unexpect- edly and cause severe injury or death. Follow Oper- ator's Manual instructions for working underneath and blocking requirements or have work done by a qualified dealer.

„Do not operate or transport equipment while under the influence of alcohol or drugs.

„Operate only in daylight or good artificial light.

„Keep hands, feet, hair, and clothing away from equipment while engine is running. Stay clear of all moving parts.

„Always comply with all state and local lighting and marking requirements.

„Never allow riders on power unit or attachment.

„Always sit in power unit seat when operating controls or starting engine. Securely fasten seat belt, place transmission in neutral, engage brake, and ensure all other controls are disengaged before starting power unit engine.

„Operate tractor PTO at 540 RPM. Do not exceed.

„Look down and to the rear and make sure area is clear before operating in reverse.

„Do not operate or transport on steep slopes.

„Do not stop, start, or change directions sud- denly on slopes.

„Use extreme care and reduce ground speed on slopes and rough terrain.

„Watch for hidden hazards on the terrain during operation.

„Stop power unit and implement immediately upon striking an obstruction. Dismount power unit, using proper procedure. Inspect and repair any damage before resuming operation.

TRANSPORTATION

„Use additional caution and reduce speed when under adverse surface conditions, turning, or on inclines.

„Do not operate PTO during transport.

„A minimum 25% of tractor and equipment weight must be on the tractor front wheels when attachments are in transport position. Without this weight, tractor could tip over, causing personal injury or death. The weight may be attained with a loader. Weigh the tractor and equipment. Do not estimate.

„Do not operate or transport on steep slopes.

„Do not operate or transport equipment while under the influence of alcohol or drugs.

„Always comply with all state and local lighting and marking requirements.

„Never allow riders on power unit or attachment.

MAINTENANCE

„Before working underneath, carefully read Oper- ator’s Manual instructions, disconnect driveline, raise mower, securely block up all corners with jackstands, and check stability. Secure blocking prevents equipment from dropping due to hydrau- lic leak down, hydraulic system failures, or mechanical component failures.

„Do not modify or alter or permit anyone else to modify or alter the equipment or any of its compo- nents in any way.

„Always wear relatively tight and belted clothing to avoid entanglement in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head; and respirator or filter mask where appropriate.

„Make sure attachment is properly secured, adjusted, and in good operating condition.

„Keep all persons away from operator control area while performing adjustments, service, or maintenance.

„Make certain all movement of equipment com- ponents has stopped before approaching for ser- vice.

„Never go underneath equipment (lowered to the ground or raised) unless it is properly blocked and secured. Never place any part of the body under- neath equipment or between moveable parts even

6Safety

RD 54/60/72 (Rev. 1/12/2007)

Image 6
Contents Heritage Rear Discharge Mower Introduction To the DealerTable of Contents LEA EL InstructivoSpecifications General InformationRD60 RD72 Training SafetySafety Rules PreparationMaintenance TransportationStorage Safety & Instructional Decals 11 20106 Rear Reflector RD60 & RD72 OnlySerial Number Plate Replace Immediately If Damaged Be CarefulOperation OperationAttach Mower to Tractor Tractor Top Link Adjustment Adjust Cutting HeightRDC54 Only Front Caster Wheel Interference Check Front Roller OptionalOperating Technique Removing Mower from Tractor Storage Owner PRE-OPERATION Check ListBlocking Method Owner ServiceOwner Service Lubrication InformationService Belt Replace BeltDescription Frequency Install Belt Sharpen BladesRefer to Figure Chain Shielding Install BladesCleaning After Each UseTroubleshooting Mowing ConditionsTrouble Shooting Belt ConditionsRemove Spindle Dealer ServiceBlade Spindle Repair Disassemble SpindleGearbox Repair Seal ReplacementSeal Installation Assemble SpindleSeal Installation Remove Gearbox from Mower Vertical Shaft Seal ReplacementHorizontal Shaft Seal Replacement Disassemble GearboxRD60 & RD72 Install GearboxInstall Drive Sheave All ModelsJoint Disassembly Universal Joint RepairJoint Assembly Install A-Frame Arms AssemblyAssembly Instructions Dealer SET-UP InstructionsInstall Driveshaft Install Rear Offset Link ArmsInstall Top Link Install Chain Shielding OptionalInstall Quick Hitch Kit Optional RD60 & RD72 Only Chain Shield Installed RDC54 OnlyInstall Front Roller Optional Front Roller InstallationDealer PRE-DELIVERY Check List Dealer Check ListsDealer Check Lists Dealer Delivery Check ListDealer Check Lists RDC54 PartsRDC54, RD60 & RD72 Main Frame Assembly RDC54 Part RD60 Part RD72 Part QTY DescriptionPart Description QTY Description RDC54 RDC54, RD60 & RD72 Gearbox AssemblyRDC54 QTY QTY Description PartRDC54 Driveline Assembly Comer Part QTY DescriptionRD60 & RD 72 Driveline Assembly Comer RDC54, RD60 & RD72 Driveshaft Walterscheid TWO-LOBE Shaft 40776 Bearing ring, guardRDC54, RD60 & RD72 Blade & Spindle Assembly RDC54, RD60, RD72 Belt Guide OptionalRD60 & RD72 Rear Chain Shielding Assembly Optional RDC54 Rear Chain Shield Assembly OptionalREF Part QTY Description RDC54, RD60 & RD72 Front Roller Assembly Optional RD60 & RD72 Quick Hitch KIT OptionalAppendix Bolt Torque ChartSAE Series Torque Chart Metric SeriesBolt Size Chart AbbreviationsIndex IndexWarranty Rev /23/2005 MAN0260

RD60, RD72, RDC54 specifications

Woods Equipment is renowned for its innovative and efficient landscaping solutions, and the RD series of rotary cutters exemplifies this reputation. The RD60, RDC54, and RD72 models are designed to cater to varying needs in land management, providing robust performance and ease of use.

The RD60 model stands out for its impressive cutting width of 60 inches, making it an ideal choice for commercial and residential applications. Its heavy-duty construction ensures longevity, with a rugged deck design that can withstand challenging terrains. The RD60 features a slip clutch protection system that prevents damage to the cutter during operation by absorbing shock loads. Additionally, its adjustable skids allow for varied cutting heights, making it versatile for different types of vegetation.

RDC54, while slightly smaller with a cutting width of 54 inches, is designed with a focus on efficiency and maneuverability. Its compact build makes it perfect for smaller properties or tight spaces. The RDC54 boasts a quick-attach mounting system, enabling users to easily connect and disconnect the cutter from their tractor. Users can also appreciate the innovative dual-blade design that enhances cutting performance, resulting in a finer mulch for improved decomposition when tackling thicker grass and brush.

On the other hand, the RD72 takes productivity to the next level with its 72-inch cutting width. This model is particularly favored by professionals looking to cover large areas quickly. Equipped with an advanced drive system, the RD72 delivers consistent power to its blades, ensuring clean cuts even in tough conditions. The model features a robust frame and reinforced side panels, making it suitable for heavy-duty applications. Furthermore, its quick-adjustment feature allows operators to change the cutting height smoothly and efficiently, maximizing versatility.

All models in the RD series incorporate cutting-edge technology, such as optimized blade design and improved airflow, which contributes to a cleaner and more efficient cut. Durability is a common theme across the series, with high-quality materials used throughout the construction ensuring these rotary cutters can handle the rigors of daily use.

In conclusion, Woods Equipment's RD60, RDC54, and RD72 rotary cutters offer a blend of durability, efficiency, and advanced features, catering to the diverse needs of landscape professionals and property owners alike. Whether the job requires finesse or brute force, there's an RD model built to deliver results.