Yazoo/Kees ZMBI48181, ZMKW48191, ZMKW52211, ZMKW52231, ZMKH52231, ZMKW61231 Hardware, Air filter

Page 22

MAINTENANCE

Hardware

Check daily. Inspect the entire machine for loose or missing hardware.

Air filter

See engine manufacturers specifications for cleaning and replacement intervals.

Hydraulic system

Check oil level in tank daily. Oil level should be 3/ 4” to 1” below the top of the tank. Check all fit- tings, hoses and lines for damage or leaks. Re- place or repair any questionable lines or fittings.

ONLY USE

Tri-Synthetic Formula

0

FIG - 11

Change the oil and filter after the first 250 hours of operation then annually after that. Drain tank and remove filter, be sure to clean around the tank and filter head before removal. Replace filter and drain plug and refill hydraulic tank. Only use MOBIL 1 synthetic oil. FIG - 11.

Raise and block up the rear of the machine so the drive wheels can rotate freely. Start the engine at the lowest RPM possible, move the motion con- trol levers forward and run machine for several minutes. Stop engine and recheck the oil level.

If the wheels do not respond an air lock has oc- curred within the system. The system must be bled off of air or let the machine set overnight to allow the air time to dissipate out of the oil. DO NOT run the machine with an air lock serious dam- age can occur to the pumps and wheel motors.

WARNING!

If a leak is suspected, use a piece of cardboard or wood, NOT your hands. to check for leaks.

Escaping hydraulic oil under pressure can have sufficient force to penetrate the skin, causing serious injury.

If injured by escaping fluid, see a doctor at once. Serious infection or reaction can develop if proper medical treatment is not administered immdediately.

Deck belt

Check every 75 to 100 hours of operation. Check for severe cracking and large nicks. NOTE: The belt will show some small cracks in normal op- eration.

To replace belt lower the deck to its lowest posi- tion. Remove the foot plate and belt shields. Use a ratchet with a 9/16” socket on the spring idler bolt to relieve the tension on the belt. Slide the belt off of pulley and fully remove the belt. Reverse the proceedure for installation. See the decal on the top of deck for belt routing information. FIG - 12. After installation is complete check the belt for twists.

FIG - 12

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents ZMBI48181 ZMKW48191 ZMKW52211 ZMKW52231 ZMKH52231 ZMKW61231 Manual no REV. IR 09/13/04Page Contents Introduction IntroductionGood Service Symbols and Decals Symbols and DecalsSafety Instructions Safety InstructionsGeneral Use Keep children away from the work area Driving on Slopes Do as followsMaintenance Children8011-563 Transport Important InformationRoll Over Protection System Customer ResponsibilitiesPresentation PresentationRops Assembly Roll Over Protection System Setup and AdjustmentsTires Control Arms AdjustmentsSeat Install Engine OilMower Deck Leveling Park Brake Adjustment For Model ZBMI48181Throttle Lever Tension Motion Control Linkage Adjustment Operation Operating instructionsFuel Shut Off Key SwitchHour Meter Pump ReleaseCutter Housings MaintenanceSafety interlock system Mower bladesHydraulic system HardwareAir filter Deck beltTire pressure Pump beltLubrication Fuel filterTorque Specifications Maintenance Schedule Trouble Shooting ProblemPage Wiring Diagrams Wiring Diagrams

ZMBI48181, ZMKW48191, ZMKW52211, ZMKW52231, ZMKH52231, ZMKW61231 specifications

Yazoo/Kees is a well-regarded name in the turf care and landscaping equipment industry, particularly known for its innovative lawn care solutions. Among its impressive lineup, the models ZMBI48181, ZMKW48191, ZMKW52211, ZMKW52231, ZMKH52231, and ZMKW61231 stand out for their performance, durability, and advanced technology.

The ZMBI48181 is a robust mower designed for commercial use, featuring a powerful engine and a high-quality deck that delivers exceptional cutting performance. Its intuitive controls and ergonomic design enhance usability, ensuring that operators can work comfortably over extended periods. The ZMKW48191, on the other hand, is a compact model ideal for small to medium-sized properties. Its maneuverability combined with efficient cutting capabilities allows users to navigate tight spaces without sacrificing performance.

Moving on to the ZMKW52211 and ZMKW52231 models, these mowers feature Yazoo/Kees’s patented cutting technology, which ensures a clean cut while minimizing clumping and optimizing grass health. Both models are equipped with high-efficiency engines, offering fuel savings and reduced emissions, aligning with contemporary environmental standards.

The ZMKH52231 model introduces a hybrid option that blends traditional gas-powered engines with electric elements. This unique design not only improves fuel efficiency but also reduces noise levels, making it suitable for residential areas or noise-sensitive environments.

Finally, the ZMKW61231 is perhaps the apex of the lineup. This industrial-grade mower excels in heavy-duty applications with its powerful performance and large cutting deck. It's designed for large properties or commercial landscaping companies needing reliable equipment for extensive grass management.

Across these models, Yazoo/Kees emphasizes durability and ease of maintenance. Constructed from high-quality materials, these mowers are designed to withstand the rigors of outdoor use. Features like easy-access service points and robust frames contribute to their longevity.

In summary, the Yazoo/Kees ZMBI48181, ZMKW48191, ZMKW52211, ZMKW52231, ZMKH52231, and ZMKW61231 represent a collection of cutting-edge lawn care equipment. Each model brings unique attributes suited for various tasks, but they all share a commitment to performance, efficiency, and user comfort. For homeowners and professionals alike, these mowers provide reliable solutions that enhance productivity while delivering superior results on every lawn.
Top Page Image Contents