Windsor SCX326, 10052400 manual Solution Strainer, Changing Brush Motors, Greasing Axle

Page 27

6.SOLUTION STRAINER

The solution strainer is located in front of the left front wheel. The solution strainer protects the solenoid valve from debris. If there is little or no solution flow to the ground, check the strainer for debris. Drain the solution tank and clean the solution strainer. To remove the strainer, turn the bottom part of the strainer counterclockwise until the bottom is separated. Clean out the debris from the wire mesh and re-assemble. Make sure the O-ring gasket is in place when re-assembled

7.BRUSH MOTOR

!

Do not use a pressure washer to clean around the brush motors. Use tap pressure only.

CHANGING BRUSH MOTORS

1.With the scrub deck in the stored position, disconnect brush motor wiring connector from harness.

2.Remove shrouds from scrub deck to access and remove scrub brushes or pad drivers.

3.Remove retaining bolt, lock washer, flat washer and star drive from brush motor shaft.

4.Remove 4 brush motor mounting bolts located under scrub deck.

5.Remove brush motor.

6.Reverse steps to install.

MAINTENANCE

8.Reset end cap and realign with scribe marks on motor barrel. Reinstall the two attach bolts from cap into base.

9.Maintain alignment between motor barrel base and cap.

GREASING AXLE

1-2 Strokes of Mobiltemp®78 or compatible clay- based or calcium-based grease.

NOTE: Use hand operated grease gun only.

BRUSH MOTOR CARBON BRUSH

REPLACEMENT

1.

Scribe alignment mark on motor barrel to motor

 

 

cap. Remove two bolts.

 

2.

Remove end cap from motor.

 

 

NOTE: Motors contain two wave washers in cap.

 

 

Do not lose these.

 

3.

Release brush from spring tension. Remove

 

 

screw connecting brush wire lead to brush

 

 

holder. Clean brush holder to insure free

 

 

movement.

 

4.

Retract spring and install new brush. Install

 

 

connector screw and lead.

 

5.

When all new brushes are installed. Place all in

 

 

retracted position, held into brush holder by

 

 

spring tension.

 

6.

Carefully place end cap onto bearing on motor

 

 

shaft.

 

 

NOTE: Use care to assure wave washer

 

 

alignment.

 

7.

With end cap in partially installed position,

 

 

release all brushes to contact position with motor

 

 

commutator.

 

 

NOTE: Failure to insure all brushes are released

 

 

will result in motor failure.

4-9

 

CUTTER 36V 86039100 05/01/07

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Walk Behind Scrubber Machine Data LOG/OVERVIEW Your DealerOverview Table of Contents Model HOW to USE this ManualRead ALL Instructions Before Using this Machine Important Safety InstructionsHazard Intensity Level Hazard Intensity LevelSafety Label Location DIMENSION/CAPACITY Technical SpecificationsMeasure Special NotesHOW the Machine Works Components Controls KEY Switch Emergency SHUT-OFF Switch OptionalBrush Switch Squeegee Lift Lever Solution Control KnobVacuum Switch Squeegee Pitch Adjustment KnobBrush Pressure Indicator Parking Brake OptionalHour Meter Optional PRE-RUN Machine Inspection Emergency Stop ProceduresFilling Solution Tank Machine OperationNormal Scrubbing To Begin ScrubbingTo Stop Scrubbing Double Scrub Emptying and Cleaning TanksMaintenance Service Schedule Maintenance Daily Weekly MonthlyHRS Maintenance Batteries Battery MaintenanceChecking Battery Specific Gravity To Charge the Batteries Battery ConditionChecking Gravity Front of Machine Changing BatteriesTo Replace or Rotate Rear Squeegee Blades Adjusting SqueegeeTo Remove Squeegee Assembly Squeegee BladesTo Adjust Squeegee Pitch To Adjust Amount of Rear Squeegee DeflectionTo Replace AQUA-MIZER Squeegee Blades Uncoated Floors Replacing or Installing Scrub BrushesRecovery Tank Float SHUT-OFF Scrub BrushesChanging Brush Motors Solution StrainerBrush Motor Carbon Brush Replacement Brush MotorBrush Shrouds & Brush Skirts Traction Motor Carbon Brush ReplacementTraction Motor Circuit BreakersChanging Vacuum Motor Vacuum MotorScrub Deck Actuator Adjustment Actuator Scrub Deck REMOVAL/REPLACEMENTProblem Cause Machine TroubleshootingMachine Troubleshooting This page Left Blank Intentionally

10052400, SCX326 specifications

The Windsor SCX326 is an advanced floor cleaning machine designed specifically for commercial and industrial use. Renowned for its robust build quality and superior cleaning performance, it is an essential tool for maintaining hygiene in large spaces such as warehouses, factories, and shopping malls.

One of the standout features of the SCX326 is its powerful scrubbing system, which utilizes a dual-brush design. This system delivers a thorough clean by effectively scrubbing away dirt and grime from various floor surfaces, including tile, concrete, and terrazzo. The machine is equipped with large cylindrical brushes that can tackle stubborn stains while also being gentle on the floor, ensuring long-term safety and aesthetic appeal.

The SCX326 incorporates advanced technologies to enhance its functionality and user experience. Its intuitive control panel allows operators to easily adjust water flow, brush pressure, and cleaning speed, catering to the specific needs of different environments. Additionally, the machine is designed with a high-capacity solution tank, allowing for longer cleaning sessions without the need for frequent refills, which translates to increased productivity.

A key characteristic of the Windsor SCX326 is its eco-friendly design. It utilizes a unique water-saving technology, enabling efficient water usage while still achieving optimal cleaning results. This feature not only reduces water consumption but also minimizes the use of detergents, making it an environmentally conscious choice for businesses seeking to reduce their ecological footprint.

Safety and ease of use are paramount in the SCX326’s design. The machine is equipped with user-friendly features such as ergonomic handles, smooth maneuverability, and easy-to-access maintenance points. These elements ensure that operators can navigate tight spaces and carry out routine maintenance with minimal effort.

Furthermore, the SCX326 is built with durability in mind, utilizing high-quality materials and components that withstand the rigors of daily use. This longevity ensures a solid return on investment for businesses, as they can rely on the performance of the SCX326 for years to come.

In summary, the Windsor SCX326 is a top-tier floor cleaning solution that combines powerful scrubbing capabilities, advanced technology, and a commitment to sustainability. Its user-friendly features and durable design make it an ideal choice for facilities looking to maintain cleanliness and hygiene standards in high-traffic areas.
Top Page Image Contents