Windsor SCX326, 10052400 manual Changing Vacuum Motor

Page 29

11.VACUUM MOTOR

(Refer to the Vacuum Group in the parts section of manual)

!

Do not use a pressure washer to clean around the vacuum motors. Use tap pressure only. Care must be taken so that water is not directed into vacuum motor air intakes.

CHANGING VACUUM MOTOR

1.Disconnect batteries from machine.

2.Remove front cover.

3.Disconnect electrical connector to the vacuum motor.

4.Loosen clamp and disconnect hose from vacuum intake.

5.Remove vacuum motor mounting bracket bolts.

6.Remove vacuum motor from mounting bracket.

7.Reverse steps to install.

Vacuum Motor Carbon Brushes Replacement (Windsor)

End Cap

Carbon

Brushes

If armature commutator is grooved, extremely pitted or not concentric, the motor will need to be replaced or sent to a qualified service center.

Important:

These brushes wear quicker as the length shortens due to increased heat. Spring inside brush housing will damage motor if brushes are allowed to wear away completely.

38 [9.5mm]

Periodically check the length of the carbon brushes. Replace both carbon brushes when either is less than 3/8" (9.5mm) long.

MAINTENANCE

Vacuum Motor Carbon Brushes Replacement (Ametek))

End Cap

Carbon

Brushes

If armature commutator is grooved, extremely pitted or not concentric, the motor will need to be replaced or sent to a qualified service center.

Note:

Place stop in groove.

Important:

These brushes wear quicker as the length shortens due to increased heat. Spring inside brush housing will damage motor if brushes are allowed to wear away completely.

3/8 (9.5mm)

Periodically check the length of the carbon brushes. Replace both carbon brushes when either is less than 3/8" (9.5mm) long.

CUTTER 36V 86039100 05/01/07

4-11

Image 29
Contents Walk Behind Scrubber Overview Machine Data LOG/OVERVIEWYour Dealer Table of Contents Model HOW to USE this ManualRead ALL Instructions Before Using this Machine Important Safety InstructionsHazard Intensity Level Hazard Intensity LevelSafety Label Location DIMENSION/CAPACITY Technical SpecificationsMeasure Special NotesHOW the Machine Works Components Controls Brush Switch KEY SwitchEmergency SHUT-OFF Switch Optional Vacuum Switch Solution Control KnobSqueegee Pitch Adjustment Knob Squeegee Lift LeverHour Meter Optional Brush Pressure IndicatorParking Brake Optional Filling Solution Tank Emergency Stop ProceduresMachine Operation PRE-RUN Machine InspectionTo Stop Scrubbing Normal ScrubbingTo Begin Scrubbing Double Scrub Emptying and Cleaning TanksHRS Maintenance Service ScheduleMaintenance Daily Weekly Monthly Maintenance Batteries Battery MaintenanceChecking Gravity Checking Battery Specific Gravity To Charge the BatteriesBattery Condition Front of Machine Changing BatteriesTo Remove Squeegee Assembly Adjusting SqueegeeSqueegee Blades To Replace or Rotate Rear Squeegee BladesTo Replace AQUA-MIZER Squeegee Blades To Adjust Squeegee PitchTo Adjust Amount of Rear Squeegee Deflection Recovery Tank Float SHUT-OFF Replacing or Installing Scrub BrushesScrub Brushes Uncoated FloorsBrush Motor Carbon Brush Replacement Solution StrainerBrush Motor Changing Brush MotorsTraction Motor Traction Motor Carbon Brush ReplacementCircuit Breakers Brush Shrouds & Brush SkirtsChanging Vacuum Motor Vacuum MotorScrub Deck Actuator Adjustment Actuator Scrub Deck REMOVAL/REPLACEMENTProblem Cause Machine TroubleshootingMachine Troubleshooting This page Left Blank Intentionally

10052400, SCX326 specifications

The Windsor SCX326 is an advanced floor cleaning machine designed specifically for commercial and industrial use. Renowned for its robust build quality and superior cleaning performance, it is an essential tool for maintaining hygiene in large spaces such as warehouses, factories, and shopping malls.

One of the standout features of the SCX326 is its powerful scrubbing system, which utilizes a dual-brush design. This system delivers a thorough clean by effectively scrubbing away dirt and grime from various floor surfaces, including tile, concrete, and terrazzo. The machine is equipped with large cylindrical brushes that can tackle stubborn stains while also being gentle on the floor, ensuring long-term safety and aesthetic appeal.

The SCX326 incorporates advanced technologies to enhance its functionality and user experience. Its intuitive control panel allows operators to easily adjust water flow, brush pressure, and cleaning speed, catering to the specific needs of different environments. Additionally, the machine is designed with a high-capacity solution tank, allowing for longer cleaning sessions without the need for frequent refills, which translates to increased productivity.

A key characteristic of the Windsor SCX326 is its eco-friendly design. It utilizes a unique water-saving technology, enabling efficient water usage while still achieving optimal cleaning results. This feature not only reduces water consumption but also minimizes the use of detergents, making it an environmentally conscious choice for businesses seeking to reduce their ecological footprint.

Safety and ease of use are paramount in the SCX326’s design. The machine is equipped with user-friendly features such as ergonomic handles, smooth maneuverability, and easy-to-access maintenance points. These elements ensure that operators can navigate tight spaces and carry out routine maintenance with minimal effort.

Furthermore, the SCX326 is built with durability in mind, utilizing high-quality materials and components that withstand the rigors of daily use. This longevity ensures a solid return on investment for businesses, as they can rely on the performance of the SCX326 for years to come.

In summary, the Windsor SCX326 is a top-tier floor cleaning solution that combines powerful scrubbing capabilities, advanced technology, and a commitment to sustainability. Its user-friendly features and durable design make it an ideal choice for facilities looking to maintain cleanliness and hygiene standards in high-traffic areas.