Nortel Networks P0992639 01 specs

Installation / 47

4.Rotate the mast until the threaded hole in the base of the mast is aligned with the set screw hole in the shroud, and then tighten the set screw.

5.Route the co-axial cable along the bottom edge of the plate between the shroud and the wall plate and tie the cable up.

Note: The total length of the co-axial cables from the outdoor external antenna to the base station must not exceed

10m.

6.Insert the plastic plug into the base of the shroud to keep the weather out.

7.Feed the co-axial cable through the wall to the surge protector on the interior wall.

Installing a lightning surge protector (Canada)

Install the lightning surge protector for the outdoor omni- directional antenna to protect it from electrical surges. The recommended lightning surge protector is part number A0382082. Refer to the installation instructions that come with the antenna for more details on its installation.

To install a lightning surge protector, follow these steps:

1.Mount the surge protector on the interior wall, shown in the following illustration, as close as possible to the entry point of the co-axial cable from the outdoor external antenna. Follow the installation instructions that come with the surge protector.

P0992639 01

Modular ICS Companion Installer Guide

Image 53

Nortel Networks P0992639 01 manual Installing a lightning surge protector Canada

Contents

To be used with MICS-XC software Modular ICS Companion Installer GuidePage Table of Contents Powering up the system Programming Specifications Glossary Index Federal Communications Commission U.S. only RegulationsCompanion Base Stations Activation U.S. only Safety Norstar Companion basics Norstar Companion basics What’s new with Norstar Norstar Companion basics Planning checklist Planning the installationConfiguring Station Modules Required equipment and supplies Configuring expansion modules On a midi system On a mini system On a maxi system On a mega system Port Expansion Cartridge with Companion Routing fiber cables Non-expanded system ICS alone numbering ICS numberingTwo-port Expansion Cartridge and ICS numbering Six-port Expansion Cartridge and ICS numbering Twelve-port expanded system and ICS numbering 16 / Planning the installation Installation checklist Installation Installing Remote Power Interconnect RPI units Connecting expansion modulesInstallation planning is required for base stations RPI units must always be installed inside a building RPI unit RPI Requirements Mounting the RPI unitBase stations RPI-16 and RPI-8 required PSUs required RPI-16 PSUs 17-24 RPI-16 and 1 RPI-8 25-32 Opening the RPI cover Do not run unprotected power cables outdoors Wiring the RPIUnplug the RPI power cord Wire size Single-pair Double-pair RPI Connector Overview Ensure both pairs have the same polarity Connector Pin Signal Output Input wiring Pin RPI Connector Board Label Wire color RPI-8 BIX wiring chart Installation RPI-16 BIX wiring chart BS14 Never mount base stations in rows Installing base stationsPositioning a base station Minimum distance between office areas and base stations Mounting a base stationClearance for the base stations Clearance conditions Canada Bracket termination board Installation Sliding cover onto bracket Installing portable telephones Installing external antennas and lightning surge arrestors FCC requirements Installed antenna and lightning surge arrestor USA Planning for an outdoor external antenna USA Antenna with antenna bracket USA Installing a lightning surge arrestor USA Lightning surge arrestor and bracket USA Installation Indoor directional external antenna Canada Installation 44 / Installation Installation 46 / Installation Installing a lightning surge protector Canada Installing the lightning surge protector Canada If display shows See Powering up the system Modular ICS Companion Installer Guide P0992639 Programming affects system operation Installation programmingProgramming Norstar Programming Record Programming tools Setting Default Template defaultsCompanion defaults System programming Startup erases programming Startup programmingPerforming Startup Entering programming Changing the default templateChanging template resets programming Entering programming for system coordinators Password Registration password Norstar featuresEntering programming using other passwords Portable features Change password to avoid incorrect registration Changing the Registration password Registration Registration should normally be disabledCompanion programming Portable DNs Schedule re-evaluation during slow periods Radio data Alarm Definition Re-eval occurred? Antenna Type Cells Changing system LID de-registers all portables System logical identifier LID Software keys U.S. only Base stations must be installed and powered first Obtain the Companion ID ÇØˆÏÈÌ Record your keys in the Programming Configure base stations and portables Register your Companion portables Registering the C3060 Registering individual portablesC3060 Icons C3060 Icon function Registered as Nortel To register the C3060 To confirm that the C3060 is registered Deregistering the C3060 Measuring undirected Rssi Measuring Rssi for a C3060 Measuring directed Rssi Registering individual portables C3050 Icons Registering the C3050To register the C3050 C3050Canadaor Icon function C3050 US Rev C3050 Rev 2 US Registered as Nortel To confirm that the C3050 is registered To deregister the C3050 Deregistering the C3050 To measure undirected Rssi Measuring Rssi for a C3050 Use the Companion Provisioning Record to find the following To register the C3020 Registering the C3020 Canada only Registering To deregister the C3020 Deregistering the C3020 Canada only Measuring Rssi for a C3020 Canada only Receive Signal Strength Indicator overrides normal display 90 / Registering individual portables Measuring directed Rssi using your portable After registering the portables Testing the base stations TestingTesting the Companion portable telephones Testing the system coverage Problems with a base station TroubleshootingProblems with a portable telephone 96 / Troubleshooting Replacing a base station Verifying Radio Credits U.S. only Problems with an RPI Obtaining a Regression Key U.S. only Problems with wireless communicationObtaining a Recovery Key Troubleshooting Example Meaning Possible causes and actions Display Alarm codesDisplays Re-Eval Utam key Radio cred Cause Event messagesEvent message display Troubleshooting Event message display Cause Evt832 Evt834 Evt852 Evt873 112 / Troubleshooting Norstar Companion system components SpecificationsRemote Power Interconnect Base station Base station External antenna assembly For the US Base station plug-top power supply Outdoor omni-directional antenna For Canada Lightning surge protector For Canada Indoor directional antenna For Canada 118 / Specifications Upgrading an RPI-8 to an RPI-16 Upgrading your systemAdding Companion to a mini, midi, maxi, or mega system PSU2U RPI connections Glossary Cell assignment a heading Call Transfer See TransferCompanion portable telephone Combo Cartridge a cartridge that ICS integrated communication system The central hardware Directory number DN a unique Installer password a one-to six IncominglinegroupILG a group Key Service Unit KSU PleaseIntegrated Services Digital Network Isdn a digital Intercom keys See Intercom Radio Credits U.S. only The XC Portable Credits U.S. onlyPortable telephone See Recovery Key U.S. only See ReceiveSignalStrengthIndicatorRemote Power Interconnect RPI Registration password a M7316 Business Series Terminal System Logical Identifier LID a Undirected Receive Signal Strength Indicator Utam Recovery Key U.S. onlyUTAMInc.U.S.only The Federal Trunk Module a module that Index 130 / Index Index /131 132 / Index Index /133 Utam Index /135 136 / Index Backup programming overlays