Manuals / Nortel Networks / Marine Equipment / SONAR

Nortel Networks P0992639 01 manual Installation

Models: P0992639 01

1 144

Download 144 pages 60.53 Kb

Page 49

Installation / 43

1.Mount the antenna using four screws.

2.To prevent undue stress on the co-axial cable, secure it to the mounting surface.

3.Connect the antenna to the appropriate base station radio.

Note: The co-axial cable length must not exceed 10 m.

Installing an indoor omni-directional external antenna (Canada)

When installing an indoor omni-directional external antenna:

•Use the bracket supplied to mount the antenna on a wall or ceiling.

Note: Use of a bracket other than the one supplied may not provide the necessary clearance between the floor or wall and the antenna.

•Install the bracket so that the external antenna is vertical. The recommended mounting height on a wall is half way between the floor and the ceiling.

P0992639 01

Modular ICS Companion Installer Guide

Image 49

Nortel Networks P0992639 01 manual Installation

Contents

To be used with MICS-XC software Modular ICS Companion Installer GuidePage Table of Contents Powering up the system Programming Specifications Glossary Index Federal Communications Commission U.S. only RegulationsCompanion Base Stations Activation U.S. onlySafety Norstar Companion basics Norstar Companion basics What’s new with Norstar Norstar Companion basics Planning checklist Planning the installationConfiguring Station Modules Required equipment and suppliesConfiguring expansion modules On a midi system On a mini systemOn a maxi system On a mega system Port Expansion Cartridge with Companion Routing fiber cables Non-expanded system ICS alone numbering ICS numberingTwo-port Expansion Cartridge and ICS numbering Six-port Expansion Cartridge and ICS numberingTwelve-port expanded system and ICS numbering 16 / Planning the installation Installation checklist InstallationInstalling Remote Power Interconnect RPI units Connecting expansion modulesInstallation planning is required for base stations RPI units must always be installed inside a buildingRPI unit RPI Requirements Mounting the RPI unitBase stations RPI-16 and RPI-8 required PSUs required RPI-16 PSUs 17-24 RPI-16 and 1 RPI-8 25-32Opening the RPI cover Unplug the RPI power cord Wiring the RPIDo not run unprotected power cables outdoors Wire size Single-pair Double-pair RPI Connector OverviewEnsure both pairs have the same polarity Connector Pin Signal Output Input wiringPin RPI Connector Board Label Wire color RPI-8 BIX wiring chartInstallation RPI-16 BIX wiring chart BS14 Positioning a base station Installing base stationsNever mount base stations in rows Minimum distance between office areas and base stations Mounting a base stationClearance for the base stations Clearance conditions CanadaBracket termination board Installation Sliding cover onto bracket Installing portable telephonesInstalling external antennas and lightning surge arrestors FCC requirements Installed antenna and lightning surge arrestor USA Planning for an outdoor external antenna USA Antenna with antenna bracket USA Installing a lightning surge arrestor USALightning surge arrestor and bracket USA Installation Indoor directional external antenna Canada Installation 44 / Installation Installation 46 / Installation Installing a lightning surge protector Canada Installing the lightning surge protector Canada If display shows See Powering up the systemModular ICS Companion Installer Guide P0992639 Programming Installation programmingProgramming affects system operation Norstar Programming Record Programming toolsCompanion defaults Template defaultsSetting Default System programming Performing Startup Startup programmingStartup erases programming Changing template resets programming Changing the default templateEntering programming Entering programming for system coordinators PasswordRegistration password Norstar featuresEntering programming using other passwords Portable featuresChange password to avoid incorrect registration Changing the Registration passwordCompanion programming Registration should normally be disabledRegistration Portable DNs Schedule re-evaluation during slow periods Radio dataAlarm Definition Re-eval occurred? Antenna Type Cells Changing system LID de-registers all portables System logical identifier LIDSoftware keys U.S. only Base stations must be installed and powered firstObtain the Companion ID ÇØˆÏÈÌ Record your keys in the Programming Configure base stations and portables Register your Companion portables Registering the C3060 Registering individual portablesC3060 Icons C3060 Icon functionRegistered as Nortel To register the C3060To confirm that the C3060 is registered Deregistering the C3060 Measuring undirected Rssi Measuring Rssi for a C3060Measuring directed Rssi Registering individual portables C3050 Icons Registering the C3050To register the C3050 C3050Canadaor Icon function C3050 US Rev C3050 Rev 2 USRegistered as Nortel To confirm that the C3050 is registered To deregister the C3050 Deregistering the C3050To measure undirected Rssi Measuring Rssi for a C3050Use the Companion Provisioning Record to find the following To register the C3020 Registering the C3020 Canada onlyRegistering To deregister the C3020 Deregistering the C3020 Canada onlyMeasuring Rssi for a C3020 Canada only Receive Signal Strength Indicator overrides normal display90 / Registering individual portables Measuring directed Rssi using your portable After registering the portables Testing the Companion portable telephones TestingTesting the base stations Testing the system coverage Problems with a portable telephone TroubleshootingProblems with a base station 96 / Troubleshooting Replacing a base station Verifying Radio Credits U.S. only Problems with an RPI Obtaining a Recovery Key Problems with wireless communicationObtaining a Regression Key U.S. only Troubleshooting Displays Alarm codesExample Meaning Possible causes and actions Display Re-Eval Utam key Radio cred Event message display Event messagesCause Troubleshooting Event message display Cause Evt832Evt834 Evt852 Evt873 112 / Troubleshooting Remote Power Interconnect SpecificationsNorstar Companion system components Base station Base stationExternal antenna assembly For the US Base station plug-top power supplyOutdoor omni-directional antenna For Canada Lightning surge protector For Canada Indoor directional antenna For Canada118 / Specifications Adding Companion to a mini, midi, maxi, or mega system Upgrading your systemUpgrading an RPI-8 to an RPI-16 PSU2U RPI connectionsGlossary Cell assignment a heading Call Transfer See TransferCompanion portable telephone Combo Cartridge a cartridge thatICS integrated communication system The central hardware Directory number DN a uniqueInstaller password a one-to six IncominglinegroupILG a group Key Service Unit KSU PleaseIntegrated Services Digital Network Isdn a digital Intercom keys See IntercomPortable telephone See Portable Credits U.S. onlyRadio Credits U.S. only The XC Recovery Key U.S. only See ReceiveSignalStrengthIndicatorRemote Power Interconnect RPI Registration password aM7316 Business Series Terminal System Logical Identifier LID aUndirected Receive Signal Strength Indicator Utam Recovery Key U.S. onlyUTAMInc.U.S.only The Federal Trunk Module a module thatIndex 130 / Index Index /131 132 / Index Index /133 Utam Index /135 136 / Index Backup programming overlays