OWNER’S MANUAL

INSTALLATION

Continued

Attaching Mounting Bracket To Wall

Note: Wall anchors, mounting screws, and spacers are in hardware package. The hard- ware package is provided with heater.

Attaching To Wall Stud Method

For attaching mounting bracket to wall studs

1.Drill holes at marked locations using 9/64" drill bit.

2.Place mounting bracket onto wall. Line up last hole on each end of bracket with holes drilled in wall.

3.Insert mounting screws through bracket and into wall studs.

4.Tighten screws until mounting bracket is firmly fastened to wall studs.

Figure 9 - Folding Anchor

Figure 10 - Popping Open Anchor Wings For Thin Walls

Attaching To Wall Anchor Method

For attaching mounting bracket to hollow walls (wall areas between studs) or solid walls (concrete or masonry)

1.Drill holes at marked locations using 5/16" drill bit. For solid walls (concrete or masonry), drill at least 1" deep.

2.Fold wall anchor as shown in Figure 9.

3.Insert wall anchor (wings first) into hole. Tap anchor flush to wall.

4.For thin walls (1/2" or less), insert red key into wall anchor. Push red key to “pop” open anchor wings.

IMPORTANT: Do not hammer key! For thick walls (over 1/2" thick) or solid walls, do not pop open wings.

5.Place mounting bracket onto wall. Line up last hole on each end of bracket with wall anchors.

6.Insert mounting screws through bracket and into wall anchors.

7.Tighten screws until mounting bracket is firmly fastened to wall.

Placing Heater On Mounting Bracket

1.Locate two horizontal slots on back panel of heater.

2.Place heater onto mounting bracket. Slide horizontal slots onto stand-out tabs on mounting bracket.

Horizontal Slots

Stand-Out Tab

Installing Bottom Mounting Screws

1.Locate two bottom mounting holes. These holes are near bottom on back panel of heater (see Figure 12).

2.Mark screw locations on wall.

3.Remove heater from mounting bracket.

4.If installing bottom mounting screws into hollow or solid wall, install wall anchors. Follow steps 1 through 4 under Attach- ing To Wall Anchor Method.

If installing bottom mounting screw into wall stud, drill holes at marked lo- cations using 9/64" drill bit.

5.Replace heater onto mounting bracket.

6.Place spacers between bottom mount- ing holes and wall anchor or drilled hole.

7.Hold spacer in place with one hand. With other hand, insert mounting screw through bottom mounting hole and spacer. Place tip of screw in opening of wall anchor or drilled hole.

8.Tighten both screws until heater is firmly secured to wall. Do not over tighten.

Note: Do not replace front panel at this time. Replace front panel after making gas connections and checking for leaks (see pages 10 and 11).

Figure 12 - Installing Bottom Mounting Screws

Mounting Bracket (attached to wall)

Figure 11 - Mounting Heater Onto Mount- ing Bracket

Continued

104401

9

Page 8 Page 10
Page 9
Image 9
Vanguard Heating VP2000BTD, VP2800BTD Attaching Mounting Bracket To Wall, Placing Heater On Mounting Bracket
Page 8 Page 10

VP2800BTD, VP2000BTD specifications

The Vanguard Heating VP2800BTD and VP2000BTD are two innovative heating solutions designed to meet the demands of homeowners seeking efficient and reliable comfort during cold weather. These models combine advanced technology with user-friendly features to provide effective warmth while promoting energy savings.

One of the standout features of both the VP2800BTD and VP2000BTD is their high heating efficiency. The units utilize a powerful heating element that ensures rapid warm-up times, allowing homeowners to enjoy the benefits of immediate heat. This efficiency translates into reduced energy consumption, making these heaters an economical choice for many households, especially during the colder months.

Both models come equipped with adjustable thermostats, allowing users to set their desired temperature with precision. This feature ensures that the heating system operates only as needed, further enhancing energy efficiency and comfort. Moreover, the digital display on each model makes it easy to monitor and adjust settings, contributing to an effortless user experience.

In terms of safety, Vanguard Heating has incorporated multiple protective features into both the VP2800BTD and VP2000BTD. These heaters are equipped with overheat protection, which automatically shuts off the unit if it reaches a dangerously high temperature. Additionally, a safety tip-over switch ensures that if the unit is accidentally knocked over, it will immediately turn off, providing peace of mind for households with pets or young children.

The design of the VP2800BTD and VP2000BTD models also contributes to their appeal. Both units feature a sleek, modern aesthetic that fits seamlessly into various styles of home décor. They are compact, making them easy to place in different rooms without taking up too much space.

Furthermore, these heaters operate quietly, allowing users to maintain a comfortable atmosphere without the distraction of noisy machinery. This is particularly important for bedrooms, offices, or areas where tranquility is desired.

In summary, Vanguard Heating's VP2800BTD and VP2000BTD models stand out for their efficiency, user-friendly features, robust safety protocols, and appealing design. These units represent a harmonious blend of technology and functionality, making them excellent choices for anyone looking to enhance their indoor comfort during the winter months.
Top Page Image Contents