Windsor 10052400, SCX326 Actuator Scrub Deck REMOVAL/REPLACEMENT, Scrub Deck Actuator Adjustment

Page 30

MAINTENANCE

12.ACTUATOR SCRUB DECK REMOVAL/REPLACEMENT

FOR SAFETY: Before leaving or servicing machine, stop on a level surface, turn off machine and set parking brake (If option is installed).

1.Remove front cover.

2.Remove the two nuts below the scrub deck that attach the actuator bracket.

3.Remove clevis pin and rue ring from lower bracket of actuator, make sure not allow actuator bracket to rotate.

4.Disconnect actuator from wiring harness.

5.Remove upper clevis pin and rue ring from actuator bracket.

6.Reverse steps to install.

SCRUB DECK ACTUATOR ADJUSTMENT

The actuator will need to be adjusted when replaced.

To adjust the actuator:

1.While holding actuator barrel to prevent it from spinning, apply power to the actuator such that it is fully extended. Positive power to white wire, and negative/ground to black. Limit switch within actuator will stop it.

2.Turn barrel out one or more full turns to assure that when it is retracted it will not bind against itself.

3.While holding actuator barrel to prevent it from spinning, apply power to the actuator such that it is fully retracted. Positive power to black wire, and negative/ground to white wire. Limit switch within actuator will stop it.

4.With actuator fully retracted, turn barrel in until it touches the base of the threaded shaft.

5.At the bottomed out position, turn the barrel out 1 1/2 turns, then enough more to allow connection to lift linkage.

6.Connect actuator to lift linkage.

7.Check travel of actuator during operation.

4-12

CUTTER 36V 86039100 05/01/07

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Walk Behind Scrubber Machine Data LOG/OVERVIEW Your DealerOverview Table of Contents HOW to USE this Manual ModelImportant Safety Instructions Read ALL Instructions Before Using this MachineHazard Intensity Level Hazard Intensity LevelSafety Label Location Technical Specifications DIMENSION/CAPACITYSpecial Notes MeasureHOW the Machine Works Components Controls KEY Switch Emergency SHUT-OFF Switch OptionalBrush Switch Squeegee Pitch Adjustment Knob Solution Control KnobVacuum Switch Squeegee Lift LeverBrush Pressure Indicator Parking Brake OptionalHour Meter Optional Machine Operation Emergency Stop ProceduresFilling Solution Tank PRE-RUN Machine InspectionNormal Scrubbing To Begin ScrubbingTo Stop Scrubbing Emptying and Cleaning Tanks Double ScrubMaintenance Service Schedule Maintenance Daily Weekly MonthlyHRS Maintenance Battery Maintenance BatteriesChecking Battery Specific Gravity To Charge the Batteries Battery ConditionChecking Gravity Changing Batteries Front of MachineSqueegee Blades Adjusting SqueegeeTo Remove Squeegee Assembly To Replace or Rotate Rear Squeegee BladesTo Adjust Squeegee Pitch To Adjust Amount of Rear Squeegee DeflectionTo Replace AQUA-MIZER Squeegee Blades Scrub Brushes Replacing or Installing Scrub BrushesRecovery Tank Float SHUT-OFF Uncoated FloorsBrush Motor Solution StrainerBrush Motor Carbon Brush Replacement Changing Brush MotorsCircuit Breakers Traction Motor Carbon Brush ReplacementTraction Motor Brush Shrouds & Brush SkirtsVacuum Motor Changing Vacuum MotorActuator Scrub Deck REMOVAL/REPLACEMENT Scrub Deck Actuator AdjustmentMachine Troubleshooting Problem CauseMachine Troubleshooting This page Left Blank Intentionally

10052400, SCX326 specifications

The Windsor SCX326 is an advanced floor cleaning machine designed specifically for commercial and industrial use. Renowned for its robust build quality and superior cleaning performance, it is an essential tool for maintaining hygiene in large spaces such as warehouses, factories, and shopping malls.

One of the standout features of the SCX326 is its powerful scrubbing system, which utilizes a dual-brush design. This system delivers a thorough clean by effectively scrubbing away dirt and grime from various floor surfaces, including tile, concrete, and terrazzo. The machine is equipped with large cylindrical brushes that can tackle stubborn stains while also being gentle on the floor, ensuring long-term safety and aesthetic appeal.

The SCX326 incorporates advanced technologies to enhance its functionality and user experience. Its intuitive control panel allows operators to easily adjust water flow, brush pressure, and cleaning speed, catering to the specific needs of different environments. Additionally, the machine is designed with a high-capacity solution tank, allowing for longer cleaning sessions without the need for frequent refills, which translates to increased productivity.

A key characteristic of the Windsor SCX326 is its eco-friendly design. It utilizes a unique water-saving technology, enabling efficient water usage while still achieving optimal cleaning results. This feature not only reduces water consumption but also minimizes the use of detergents, making it an environmentally conscious choice for businesses seeking to reduce their ecological footprint.

Safety and ease of use are paramount in the SCX326’s design. The machine is equipped with user-friendly features such as ergonomic handles, smooth maneuverability, and easy-to-access maintenance points. These elements ensure that operators can navigate tight spaces and carry out routine maintenance with minimal effort.

Furthermore, the SCX326 is built with durability in mind, utilizing high-quality materials and components that withstand the rigors of daily use. This longevity ensures a solid return on investment for businesses, as they can rely on the performance of the SCX326 for years to come.

In summary, the Windsor SCX326 is a top-tier floor cleaning solution that combines powerful scrubbing capabilities, advanced technology, and a commitment to sustainability. Its user-friendly features and durable design make it an ideal choice for facilities looking to maintain cleanliness and hygiene standards in high-traffic areas.
Top Page Image Contents