Stanley Black & Decker CS06, CS05 manual Hose Types, Hose Safety Tags

Page 10

HOSE TYPES

The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic Tools. They are:

Certified non-conductive— constructed of thermoplastic or synthetic rubber inner tube, synthetic fiber braid reinforcement, and weather resistant thermoplastic or synthetic rubber cover. Hose labeled certified non- conductive is the only hose authorized for use near electrical conductors.

Wire-braided(conductive) — constructed of synthetic rubber inner tube, single or double wire braid reinforce- ment, and weather resistant synthetic rubber cover. This hose is conductive and must never be used near electrical conductors.

Fabric-braided(not certified or labeled non-conductive) — constructed of thermoplastic or synthetic rubber in- ner tube, synthetic fiber braid reinforcement, and weather resistant thermoplastic or synthetic rubber cover. This hose is not certified non-conductiveand must never be used near electrical conductors.

HOSE SAFETY TAGS

To help ensure your safety, the following DANGER tags are attached to all hose purchased from Stanley Hydraulic Tools. DO NOT REMOVE THESE TAGS.

If the information on a tag is illegible because of wear or damage, replace the tag immediately. A new tag may be obtained from your Stanley Distributor.

D O N O T R E M O V E T H I S T A G

THE TAG SHOWN BELOW IS ATTACHED TO “CERTIFIED NON-CONDUCTIVE” HOSE

 

 

 

 

 

 

 

 

 

 

 

D A N G E R

 

 

 

 

 

 

D A N G E R

 

D O

 

 

 

 

 

 

 

 

 

 

N O

 

1. FAILURE TO USE HYDRAULIC HOSE LABELED AND CERTIFIED AS NON-CONDUCTIVE

 

 

 

 

 

 

OR HANDLING OF HOSE COULD RESULT IN BURST OR OTHER HOSE FAILURE.

 

 

 

 

 

 

 

 

T

 

WHEN USING HYDRAULIC TOOLS ON OR NEAR ELECTRIC LINES MAY RESULT IN

 

 

 

 

 

 

KEEP HOSE AS FAR AWAY AS POSSIBLE FROM BODY AND DO NOT PERMIT DIRECT

 

 

 

 

 

 

 

 

 

R E

 

DEATH OR SERIOUS INJURY.

 

 

 

 

 

 

CONTACT DURING USE. CONTACT AT THE BURST CAN CAUSE BODILY INJECTION

 

 

FOR PROPER AND SAFE OPERATION MAKE SURE THAT YOU HAVE BEEN PROP-

 

 

 

 

 

 

AND SEVERE PERSONAL INJURY.

 

 

 

 

 

 

 

 

 

 

M

 

ERLY TRAINED IN CORRECT PROCEDURES REQUIRED FOR WORK ON OR AROUND

 

 

 

 

 

4.

HANDLE AND ROUTE HOSE CAREFULLY TO AVOID KINKING, ABRASION, CUTTING, OR

 

 

 

 

 

 

 

 

O

 

ELECTRIC LINES.

 

 

 

 

 

 

CONTACT WITH HIGH TEMPERATURE SURFACES. DO NOT USE IF KINKED. DO NOT

 

 

 

 

 

 

 

 

 

V

 

 

 

 

 

 

 

 

USE HOSE TO PULL OR LIFT TOOLS, POWER UNITS, ETC.

 

 

2. BEFORE USING HYDRAULIC HOSE LABELED AND CERTIFIED AS NON-CONDUCTIVE

 

 

 

 

 

 

 

E

 

 

 

 

 

 

5.

CHECK ENTIRE HOSE FOR CUTS CRACKS LEAKS ABRASIONS, BULGES, OR DAM-

 

 

 

 

 

 

 

 

T

 

ON OR NEAR ELECTRIC LINES. WIPE THE ENTIRE LENGTH OF THE HOSE AND FIT-

 

 

 

 

 

 

 

 

 

 

 

 

 

AGE TO COUPLINGS IF ANY OF THESE CONDITIONS EXIST, REPLACE THE HOSE

 

H

 

TING WITH A CLEAN DRY ABSORBENT CLOTH TO REMOVE DIRT AND MOISTURE AND

 

 

 

 

 

 

 

 

 

 

 

 

 

 

IMMEDIATELY. NEVER USE TAPE OR ANY DEVICE TO ATTEMPT TO MEND THE HOSE.

 

I

 

TEST HOSE FOR MAXIMUM ALLOWABLE CURRENT LEAKAGE IN ACCORDANCE WITH

 

 

 

 

 

 

 

S

 

 

 

 

 

 

6.

AFTER EACH USE STORE IN A CLEAN DRY AREA.

 

 

SAFETY DEPARTMENT INSTRUCTIONS.

 

 

 

 

 

 

T A

 

SEE OTHER SIDE

 

 

 

 

 

 

SEE OTHER SIDE

 

 

3. DO NOT EXCEED HOSE WORKING PRESSURE OR ABUSE HOSE. IMPROPER USE

 

 

 

 

 

 

 

 

G

 

 

 

 

 

 

 

 

 

 

 

 

SIDE 1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SIDE 2

 

 

(Shown smaller than actual size)

THE TAG SHOWN BELOW IS ATTACHED TO “CONDUCTIVE” HOSE.

D O N O T R E M O V E T H I S T A G

 

D A N G E R

 

 

D A N G E R

 

 

 

 

 

1.

DO NOT USE THIS HYDRAULIC HOSE ON OR NEAR ELECTRIC LINES. THIS HOSE IS

5.

CHECK ENTIRE HOSE FOR CUTS CRACKS LEAKS ABRASIONS, BULGES, OR DAMAGE TO

 

NOT LABELED OR CERTIFIED AS NON-CONDUCTIVE. USING THIS HOSE ON OR NEAR

 

COUPLINGS IF ANY OF THESE CONDITIONS EXIST, REPLACE THE HOSE IMMEDIATELY.

 

ELECTRICAL LINES MAY RESULT IN DEATH OR SERIOUS INJURY.

 

NEVER USE TAPE OR ANY DEVICE TO ATTEMPT TO MEND THE HOSE.

2.

FOR PROPER AND SAFE OPERATION MAKE SURE THAT YOU HAVE BEEN PROPERLY

6.

AFTER EACH USE STORE IN A CLEAN DRY AREA.

 

TRAINED IN CORRECT PROCEDURES REQUIRED FOR WORK ON OR AROUND ELEC-

 

SEE OTHER SIDE

 

TRIC LINES.

 

 

 

 

3.DO NOT EXCEED HOSE WORKING PRESSURE OR ABUSE HOSE. IMPROPER USE OR HAN- DLING OF HOSE COULD RESULT IN BURST OR OTHER HOSE FAILURE. KEEP HOSE AS FAR AWAY AS POSSIBLE FROM BODY AND DO NOT PERMIT DIRECT CONTACT DURING USE. CONTACTAT THE BURST CAN CAUSE BODILY INJECTION AND SEVERE PERSONAL INJURY.

4.HANDLE AND ROUTE HOSE CAREFULLY TO AVOID KINKING, CUTTING, OR CONTACT WITH HIGH TEMPERATURE SURFACES. DO NOT USE IF KINKED. DO NOT USE HOSE TO PULL OR LIFT TOOLS, POWER UNITS, ETC.

SEE OTHER SIDE

 

SIDE 1

SIDE 2

(Shown smaller than actual size)

D O N O T R E M O V E T H I S T A G

10 ► CS05/CS06 User Manual

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Hydraulic Chain SAW Page Table of Contents Safety Symbols Local Safety RegulationsSafety Precautions Safety Precautions Electrical Precautions Working in Proximity to Electrical HazardsStorm Work and Emergency CONDITIONS-LINE Clearance 107 Tool Stickers & TagsHose Safety Tags Hose TypesHose Recommendations Tool to Hydraulic Circuit Hose RecommendationsHtma / Ehtma Requirements Htma / Ehtma RequirementsOperating Procedures Preoperation ProceduresOperation Felling or Back CUT Felling Cutting Down a Tree FigureNotching or Undercutting BuckingLogs with Pressure on TOP Figure Crosscutting Logs with Pressure on TopLOGS/LIMBS with Pressure on Bottom Figure Crosscutting Logs/Limbs with Pressure on BottomCold Weather Operation Pruning and DebranchingTool Protection & Care Troubleshooting Problem Cause RemedyAccessories Service ToolsCS05/CS06 Parts Illustration CS05/CS06 Parts List Part QTY DescriptionKeeper Underwater Models only Underwater Tools Depth GuidelineGPM

CS05, CS06 specifications

Stanley Black & Decker is well-known for its innovative solutions and high-quality tools, and its CS05 and CS06 models exemplify these qualities. These products are integral to both professional contractors and DIY enthusiasts, representing the brand's commitment to durability, efficiency, and user-friendly design.

The Stanley Black & Decker CS05 is characterized by its powerful performance and compact design. This model is equipped with a high-efficiency motor that delivers exceptional cutting power. Its lightweight construction enhances maneuverability, making it an easy choice for complex jobs in tight spaces. The CS05 also features an ergonomic handle, designed for maximum comfort during extended use.

One of the notable technologies in the CS05 is its advanced blade system. The blade can be easily adjusted, allowing users to switch between different cutting applications seamlessly. The model also incorporates a safety guard to protect users from accidental blade exposure, ensuring a safer operation for both professionals and hobbyists alike.

On the other hand, the CS06, while similar in many respects, includes several upgraded features that enhance its functionality. With an even more robust motor, the CS06 can handle tougher materials, making it ideal for heavy-duty applications. This model boasts an integrated laser guide system that improves precision, ensuring that cuts are accurate every time.

Moreover, the CS06 is designed with a quick-release mechanism for blade changes, minimizing downtime and allowing for more efficient workflows. The durable casing of the CS06 is engineered to withstand harsh job site conditions, providing longevity and reliability.

Both models incorporate Stanley Black & Decker's Smart Technology, which optimizes power consumption while maximizing output. This not only contributes to energy efficiency but also extends the overall lifespan of the tools.

In summary, the Stanley Black & Decker CS05 and CS06 are powerful, versatile, and user-centric tools that embody the brand's dedication to quality and innovation. Whether you're tackling intricate DIY projects or major construction tasks, these models deliver the performance and reliability you need. With their combined cutting-edge features and technologies, they stand out in the competitive landscape of professional-grade tools.
Top Page Image Contents