Stanley Black & Decker CS05, CS06 manual Operation, Preoperation Procedures, Operating Procedures

Page 13

OPERATION

PREOPERATION PROCEDURES

CHECK POWER SOURCE

1.Using a calibrated flowmeter and pressure gauge, check that the hydraulic power source develops a flow of 4-6 gpm/15-23 lpm at 1500-2000 psi/105- 140 bar for the CS05 or a flow of 7-9 gpm/26-34 lpm at 1000-2000 psi/70-140 bar for the CS06.

2.Make certain that the hydraulic power source is equipped with a relief valve set to open at 2100-­ 2250 psi/145-155 bar.

CONNECT HOSES

1.Wipe all hose couplers with a clean lint-free cloth before making connections.

2.Connect the hoses from the hydraulic power source to the tool fittings or quick disconnects. It is good practice to connect return hoses first and discon- nect them last to minimize or avoid trapped pressure within the tool.

3.Observe the arrow on the couplers to ensure that the flow is in the proper direction. The female cou- pler on the tool hose is the inlet (pressure) coupler.

4.Move the hydraulic circuit control valve to the “ON” position to operate the tool.

NOTE:

If uncoupled hoses are left in the sun, pressure in- crease inside the hose may make them difficult to connect. Whenever possible, connect the free ends of the hoses together.

SYSTEM SELECTION (OC/CC)

Saws configured with the system selector option require setup for the system, closed-center (CC) or open-center (CC), in which it will operate. The selector screw is lo- cated in the bottom end of the valve spool.

1.Determine the system type.

2.For operation in a CC system, turn the selector screw fully clockwise. When the selector screw bot- toms, CC operation is selected.

3.For operation in an OC system, turn the selector screw counter-clockwise until meeting resistance (from the retaining ring). Turn the selector screw clockwise and then counter-clockwise to be sure that you are sensing resistance of the retaining ring. Do not force the selector screw.

IMPORTANT

To prevent damage to the retaining ring, do not

attempt to force the selector screw counter-clockwise

beyond the point of initial resistance.

OPERATING PROCEDURES

The following are general wood cutting­ procedures and techniques. Differences­ in the terrain, vegetation, and type of wood will make this infor­mation more or less val- id for particu­lar areas. For advice on specific woodcut- ting problems or techniques for your area, consult your local Stanley representative or your county agent. They can often provide information­ that will make your work safer and more productive.

CUTTING TIPS

1.Check the lean of the tree. Tie a weight to a piece of string about 2 feet long. Hang the weight in your line of sight. The string is a good vertical line to help you judge the lean of the tree. The tree should fall the way it is leaning. Trees that are straight (leaning no more than 5 degrees) generally­ can be felled in any direction.

2.Avoid felling across another tree, log, rocks, gully or ridge. Do not fell straight uphill or downhill­. Fell the tree diagonally to the hill. Consider the wind direc- tion and velocity. Do not attempt cutting in strong winds.

3.Check the weight distribution. A tree is heavier on the side with the most limbs. It will try to fall on its heavy side. Trim a few limbs to “balance” the tree.

4.Clear the work area. You need a clean area all around the tree for good footing. Get every­thing out of the area where the tree will fall. Do not cut trees near structures. Because of the danger of electro- cution, use extreme care when cutting trees near power lines.

5.Before starting the cut, prepare your escape path. Make sure the escape path is clear of brush and branches. The escape path should be at an angle away from the direction of fall.

CS05/CS06 User Manual ◄ 13

Image 13
Contents Hydraulic Chain SAW Page Table of Contents Local Safety Regulations Safety SymbolsSafety Precautions Safety Precautions Working in Proximity to Electrical Hazards Electrical PrecautionsStorm Work and Emergency CONDITIONS-LINE Clearance Tool Stickers & Tags 107Hose Types Hose Safety TagsTool to Hydraulic Circuit Hose Recommendations Hose RecommendationsHtma / Ehtma Requirements Htma / Ehtma RequirementsOperating Procedures Preoperation ProceduresOperation Notching or Undercutting Felling Cutting Down a Tree FigureFelling or Back CUT BuckingCrosscutting Logs with Pressure on Top Logs with Pressure on TOP FigureCrosscutting Logs/Limbs with Pressure on Bottom LOGS/LIMBS with Pressure on Bottom FigurePruning and Debranching Cold Weather OperationTool Protection & Care Problem Cause Remedy TroubleshootingService Tools AccessoriesCS05/CS06 Parts Illustration Part QTY Description CS05/CS06 Parts ListKeeper Underwater Models only Underwater Tools Depth GuidelineGPM

CS05, CS06 specifications

Stanley Black & Decker is well-known for its innovative solutions and high-quality tools, and its CS05 and CS06 models exemplify these qualities. These products are integral to both professional contractors and DIY enthusiasts, representing the brand's commitment to durability, efficiency, and user-friendly design.

The Stanley Black & Decker CS05 is characterized by its powerful performance and compact design. This model is equipped with a high-efficiency motor that delivers exceptional cutting power. Its lightweight construction enhances maneuverability, making it an easy choice for complex jobs in tight spaces. The CS05 also features an ergonomic handle, designed for maximum comfort during extended use.

One of the notable technologies in the CS05 is its advanced blade system. The blade can be easily adjusted, allowing users to switch between different cutting applications seamlessly. The model also incorporates a safety guard to protect users from accidental blade exposure, ensuring a safer operation for both professionals and hobbyists alike.

On the other hand, the CS06, while similar in many respects, includes several upgraded features that enhance its functionality. With an even more robust motor, the CS06 can handle tougher materials, making it ideal for heavy-duty applications. This model boasts an integrated laser guide system that improves precision, ensuring that cuts are accurate every time.

Moreover, the CS06 is designed with a quick-release mechanism for blade changes, minimizing downtime and allowing for more efficient workflows. The durable casing of the CS06 is engineered to withstand harsh job site conditions, providing longevity and reliability.

Both models incorporate Stanley Black & Decker's Smart Technology, which optimizes power consumption while maximizing output. This not only contributes to energy efficiency but also extends the overall lifespan of the tools.

In summary, the Stanley Black & Decker CS05 and CS06 are powerful, versatile, and user-centric tools that embody the brand's dedication to quality and innovation. Whether you're tackling intricate DIY projects or major construction tasks, these models deliver the performance and reliability you need. With their combined cutting-edge features and technologies, they stand out in the competitive landscape of professional-grade tools.