Stanley Black & Decker 387002x92NA manual Maintenance Free Battery

Page 11

ASSEMBLY

MAINTENANCE FREE BATTERY

IMPORTANT: Before you attach the battery cables to the battery, check the battery date. The battery date tells if the battery must be charged.

1.Check the top of the battery for the location of the battery date (Figure 2).

2.If the battery is put into service before the battery date, the battery cables can be attached without charging the battery. See “How To Install The Battery Cables”.

3.If the battery is put into service after the battery date, the battery must be charged. See “How To Charge The Maintenance Free Battery”.

HOW TO CHARGE THE MAINTENANCE FREE BATTERY

WARNING: When you charge the battery, do not smoke. Keep the battery away from any sparks. The fumes from the battery acid can cause an explosion.

1.Remove the battery. See “How To Remove The Battery”.

2.Remove the protective caps from the battery terminals.

3.Use a 12 volt battery charger to charge the battery. Charge at a rate of 6 amperes for one hour. If you do not have a battery charger, have an authorized service center charge the battery.

4.Install the battery. See “How To Install The Battery”.

HOW TO REMOVE THE BATTERY

1.Rotate the battery clamp to the DOWN position (Figure 1 and Figure 2).

2.To remove the battery, tilt the battery forward and then lift the battery.

CAUTION: Do not tilt the battery more than 45 degrees. If the battery tilts more than 45 degrees, battery acid can leak from the battery.

UP – Operating Position

SIDE

Battery Clamp

 

VIEW

 

 

DOWN – Removal Position

 

Figure 1

HOW TO INSTALL THE BATTERY

1.Install the battery tray (Figure 3). Make sure the drain on the bottom of the battery tray goes through the hole in the frame as shown in Figure 3.

2.Turn the battery so that the positive (+) terminal is on the right side of the unit. Set the battery in the battery tray.

IMPORTANT: Make sure the battery fits under the tabs at the back of the unit.

3.Rotate the battery clamp to the UP position (Figure 1 and Figure 3).

HOW TO INSTALL THE BATTERY CABLES

WARNING: To prevent sparks, fasten the red cable to the positive (+) terminal before you connect the black cable.

NOTE: Before you attach the battery cables, make sure the battery is fully charged. This will extend the life of the battery and provide the necessary power to start the engine.

2.If equipped, slide the terminal cover onto the red cable (Figure 3). Fasten the red cable to the positive (+) terminal with the fasteners as shown. Push the terminal cover onto the battery terminal.

3.Fasten the black cable to the negative (–) terminal with the fas- teners as shown.

Battery Date Code

Battery

 

Battery Clamp

 

DOWN position

 

Figure 2

 

Black Cable

Tabs

A

 

 

B

A

B

 

Battery Clamp

Battery

UP Position

 

Red Cable

Terminal

Use the fasteners shown below to install the battery cables. The fasteners are shown at full size.

Positive (+)

Terminal

Cover

(A)

(B)

2x82

14x79

1.Remove the protective caps from the battery terminals.

Battery Tray

Drain

Figure 3

F–040700C

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Model Table of Contents Responsibility of the Owner OWNER’S InformationII. Slope operation Safe Mowing Guide Safe Mowing Guide Safe Mowing Guide Before Mowing Steps to FollowInternational Pictorials International PictorialsAssembly AssemblyHOW to Charge the Maintenance Free Battery Maintenance Free BatteryHOW to Assemble the Steering Wheel HOW to Install the SeatCheck the Tires HOW to Prepare the EngineCheck the Level of the Mower Housing IMPORTANT! Before YOU Start MowingLift Lever OperationLocation of Controls Attachments HOW to USE the Throttle ControlHOW to USE the Shift Lever HOW to Transport the Unit HOW to SET the Parking BrakeHOW to Change the Cutting Height HOW to Stop the UnitHOW to Operate the Unit on Hills HOW to Operate with the Mower HousingCarburetor HOW to Start the EngineHOW to Start with a Weak Battery Before Starting the EngineMowing and Bagging Tips Operating TipsGeneral Recommendations MaintenanceMaintenance Chart HOW to Check the MufflerInspect Blade HOW to Remove and Install the BladeHOW to Sharpen the Blade HOW to Adjust the Blade Rotation Control HOW to Check and Adjust the Clutch HOW to Check and Adjust the Drive BrakeHOW to Clean the Battery HOW to Check the Fuel Filter Where to LubricateHOW to Install the Mower Housing HOW to Remove the Mower HousingSide to Side Adjustment HOW to Level the Mower HousingFront to Back Adjustment Removal HOW to Replace the Motion Drive BeltHOW to Replace the Mower Drive Belt Front Wheel HOW to Install the WheelsBattery HOW to Replace the FuseHOW to Replace the Light Bulb HOW to Clean the Mower HousingProblem The engine will not start Trouble Shooting ChartFrank Edwards CO CPT Canada Power Technology LimitedBILLIOU’S, INC Brown & WISER, INCChassis & Hood Repair PartsKey Description Repair Parts Motion Drive Motion Drive Steering Key Part Description Mower Housing Suspension Repair Parts Mower Housing Key Description Repair Parts Engine Mount Repair Parts Repair Parts Electrical System Electrical System 040700C 040700C 040700C Index Lawn Tractor Accessories

387002x92NA specifications

The Stanley Black & Decker 387002X92NA is a versatile and innovative tool that stands out in the realm of power tools. Designed for both professionals and DIY enthusiasts, this product exemplifies quality, reliability, and advanced technology. One of the main features of the Stanley Black & Decker 387002X92NA is its high-performance motor, which delivers impressive torque and speed, making it suitable for a wide range of applications. Whether you're drilling into wood, metal, or masonry, this tool offers the versatility required to tackle various projects with ease.

Incorporating cutting-edge technology, the Stanley Black & Decker 387002X92NA is equipped with an electronic control system that optimizes power usage, extending the lifespan of the tool. Additionally, its variable speed settings allow users to adjust the tool's performance to match specific tasks, providing greater control and precision. This feature is particularly beneficial for intricate jobs where accuracy is paramount.

The ergonomic design of the 387002X92NA ensures a comfortable grip, reducing user fatigue during extended use. The lightweight nature of the tool also enhances mobility, making it easy to maneuver in tight spaces. Furthermore, the inclusion of an LED work light illuminates darker work areas, improving visibility and safety while working.

Durability is another hallmark of the Stanley Black & Decker 387002X92NA. Constructed from high-quality materials, the tool is built to withstand rigorous use in demanding environments. Its rugged housing provides resistance against drops and impacts, ensuring longevity even under heavy-duty conditions.

For added convenience, the tool features a quick-change chuck system that enables users to swap out bits rapidly without the need for additional tools. This user-friendly design element enhances efficiency, allowing for seamless transitions between tasks.

In conclusion, the Stanley Black & Decker 387002X92NA is a powerful, durable, and user-friendly tool that integrates advanced technologies and innovative features. Ideal for professionals and hobbyists alike, it excels in performance and versatility, making it a valuable addition to any toolkit. Whether you're embarking on home improvement projects or tackling heavy-duty commercial tasks, this tool delivers the reliability and effectiveness needed to get the job done right.
Top Page Image Contents