Stanley Black & Decker 387002x92NA manual HOW to Adjust the Blade Rotation Control

Page 22

MAINTENANCE

HOW TO ADJUST THE BLADE ROTATION CONTROL

WARNING: To prevent an injury, the blade rotation control must operate correctly.

1.Stop the engine. Disconnect the wire from the spark plug.

2.Before you adjust the blade rotation control, check and level the mower housing. See “How To Level The Mower Housing.” Make sure the mower housing is level before go to the next step.

3.Set the height of the mower housing in the lowest position.

4.Move the blade rotation control to the ENGAGE position (Figure 14). Check the plastic indicator inside the blade drive spring (Figure 15). The end of the plastic indicator must be aligned ( + or – 1/8 inch / 3 mm) with the last coil of the blade drive spring.

5.If the plastic indicator is more than 1/8 inch (3 mm) from the last spring coil, an adjustment is needed. Move the blade rota- tion control to the DISENGAGE position. Disconnect the blade control rod from the pivot bracket. Turn the adjustable nut clockwise to increase the length of the coils. Turn the ad- justable nut counterclockwise to decrease the length of the coils.

6.Connect the blade control rod to the pivot bracket. Move the blade rotation control to the ENGAGE position. Check the adjustment of the blade drive spring.

7.Move the blade rotation control to the DISENGAGE posi- tion. Check the operation of the blade brake. Rotate the pulley with your hand. Make sure the pads for the blade brake are pressed tightly against the pulleys.

IMPORTANT: If the brake pads do not press tightly against the pulleys, replace the mower drive belt and repeat steps 1–7. Then, complete the remaining steps. Correct replacement parts and assistance are available from an authorized service center.

8.Move the blade rotation control to the ENGAGE position. Check the pads for the blade brake. If the pads are excessively

Blade Rotation Control

Engage Position

Throttle

Control

Disengage

Position

Figure 14

worn or damaged, replace the brake pad assemblies. Correct replacement parts and assistance are available from an autho- rized service center.

9.Attach the wire to the spark plug. Mow for a short distance and again check the operation of the blade rotation control.

10.When you move the blade rotation control to the DISENGAGE position, all movement will stop within five sec- onds if the adjustment is correct. If there is movement of the belt or the blades continue to rotate, engage and disengage the blade rotation control five times to remove any excess rubber from a new mower drive belt. If there is still blade rotation from the DISENGAGED position, adjust the blade drive spring until more of the plastic indicator extends beyond the end of the last coil. This adjustment will decrease the spring tension. If you need assistance, take the unit to an authorized service center.

11.After you operate with a new mower drive belt for several hours, check the tension of the blade drive spring.

12.If you replace the mower drive belt, adjust the blade rotation control.

 

–1/8”

Blade Control Rod

 

+1/8”

(3mm)

 

Brake Pad Against Pulley

(3mm)

 

 

 

 

 

 

 

Plastic Indicator

 

 

Pivot Bracket

Adjustable

 

 

 

 

Nut

Blade Drive Spring

 

 

 

 

 

 

 

Blade Brake

 

 

 

 

(Brake Pad Against Pulley)

 

 

 

Mower Drive Belt

Figure 15

F–040700C

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Model Table of Contents OWNER’S Information Responsibility of the OwnerII. Slope operation Safe Mowing Guide Safe Mowing Guide Safe Mowing Guide Steps to Follow Before MowingInternational Pictorials International PictorialsAssembly AssemblyMaintenance Free Battery HOW to Charge the Maintenance Free BatteryHOW to Install the Seat HOW to Assemble the Steering WheelIMPORTANT! Before YOU Start Mowing HOW to Prepare the EngineCheck the Level of the Mower Housing Check the TiresLocation of Controls OperationLift Lever HOW to USE the Shift Lever HOW to USE the Throttle ControlAttachments HOW to Stop the Unit HOW to SET the Parking BrakeHOW to Change the Cutting Height HOW to Transport the UnitHOW to Operate with the Mower Housing HOW to Operate the Unit on HillsBefore Starting the Engine HOW to Start the EngineHOW to Start with a Weak Battery CarburetorOperating Tips Mowing and Bagging TipsHOW to Check the Muffler MaintenanceMaintenance Chart General RecommendationsHOW to Sharpen the Blade HOW to Remove and Install the BladeInspect Blade HOW to Adjust the Blade Rotation Control HOW to Check and Adjust the Drive Brake HOW to Check and Adjust the ClutchHOW to Clean the Battery Where to Lubricate HOW to Check the Fuel FilterHOW to Remove the Mower Housing HOW to Install the Mower HousingFront to Back Adjustment HOW to Level the Mower HousingSide to Side Adjustment HOW to Replace the Motion Drive Belt RemovalHOW to Replace the Mower Drive Belt HOW to Install the Wheels Front WheelHOW to Clean the Mower Housing HOW to Replace the FuseHOW to Replace the Light Bulb BatteryTrouble Shooting Chart Problem The engine will not startBrown & WISER, INC CPT Canada Power Technology LimitedBILLIOU’S, INC Frank Edwards CORepair Parts Chassis & HoodKey Description Repair Parts Motion Drive Motion Drive Steering Key Part Description Mower Housing Suspension Repair Parts Mower Housing Key Description Repair Parts Engine Mount Repair Parts Repair Parts Electrical System Electrical System 040700C 040700C 040700C Index Lawn Tractor Accessories

387002x92NA specifications

The Stanley Black & Decker 387002X92NA is a versatile and innovative tool that stands out in the realm of power tools. Designed for both professionals and DIY enthusiasts, this product exemplifies quality, reliability, and advanced technology. One of the main features of the Stanley Black & Decker 387002X92NA is its high-performance motor, which delivers impressive torque and speed, making it suitable for a wide range of applications. Whether you're drilling into wood, metal, or masonry, this tool offers the versatility required to tackle various projects with ease.

Incorporating cutting-edge technology, the Stanley Black & Decker 387002X92NA is equipped with an electronic control system that optimizes power usage, extending the lifespan of the tool. Additionally, its variable speed settings allow users to adjust the tool's performance to match specific tasks, providing greater control and precision. This feature is particularly beneficial for intricate jobs where accuracy is paramount.

The ergonomic design of the 387002X92NA ensures a comfortable grip, reducing user fatigue during extended use. The lightweight nature of the tool also enhances mobility, making it easy to maneuver in tight spaces. Furthermore, the inclusion of an LED work light illuminates darker work areas, improving visibility and safety while working.

Durability is another hallmark of the Stanley Black & Decker 387002X92NA. Constructed from high-quality materials, the tool is built to withstand rigorous use in demanding environments. Its rugged housing provides resistance against drops and impacts, ensuring longevity even under heavy-duty conditions.

For added convenience, the tool features a quick-change chuck system that enables users to swap out bits rapidly without the need for additional tools. This user-friendly design element enhances efficiency, allowing for seamless transitions between tasks.

In conclusion, the Stanley Black & Decker 387002X92NA is a powerful, durable, and user-friendly tool that integrates advanced technologies and innovative features. Ideal for professionals and hobbyists alike, it excels in performance and versatility, making it a valuable addition to any toolkit. Whether you're embarking on home improvement projects or tackling heavy-duty commercial tasks, this tool delivers the reliability and effectiveness needed to get the job done right.
Top Page Image Contents