Stanley Black & Decker 387002x92NA manual Before Starting the Engine, Carburetor

Page 18

OPERATION

BEFORE STARTING THE ENGINE

CHECK THE OIL

NOTE: The engine was shipped from the factory filled with SAE 30 weight oil. Check the level of the oil. Add oil as needed.

1.Make sure the unit is level.

NOTE: Do not check the level of the oil while the engine runs.

2.Clean the area around the dipstick. Remove the dipstick. Wipe the oil from the dipstick.

3.Insert the dipstick into the oil fill tube. Turn the dipstick clock- wise until it is tight. Remove the dipstick. Check the oil level on the dipstick. The oil level must reach the FULL mark on the dipstick.

4.If necessary, add oil until the oil reaches the FULL mark on the dipstick. The quantity of oil needed from ADD to FULL is shown on the dipstick. Do not add too much oil.

CAUTION: A mixture of alcohol (ethanol or methanol) and gasoline (called gasohol), will attract moisture and cause acid deposits during storage. While the unit is in storage, the acids in the fuel can damage the fuel system.

To prevent engine problems with the fuel system, empty the fuel system before storage of 30 days or longer as follows.

1.Drain the fuel tank.

2.Start the engine. Let the engine run until the fuel lines and the carburetor are empty.

3.After storage, make sure you use fresh fuel. See the storage instructions for additional information.

4.Never use engine cleaner or carburetor cleaner in the fuel tank or permanent damage can occur.

ADD GASOLINE

WARNING: Always use a safety gasoline container. Do not smoke when adding gasoline to the fuel tank. Do not add gasoline when you are inside an enclo- sure. Before you add gasoline, stop the engine and let the engine cool for several minutes.

CARBURETOR

The factory settings for the carburetor are for most conditions. If the engine is operated under the following conditions, you can adjust the carburetor mixture. To adjust the carburetor, see the engine manufacturer’s instructions.

Fill the

fuel tank with regular

 

Fuel Tank

1.

The engine has a loss of power or does not run smooth.

unleaded gasoline. Do not use

 

 

 

 

 

2.

A change from summer to winter operation.

premium

unleaded gasoline.

Full

 

Make sure the gasoline is fresh

 

 

3.

A 40 degree change in the operation temperature. The carbure-

and clean. Leaded gasoline will

 

 

 

 

 

tor was adjusted at 80 degrees at the factory.

increase

deposits and shorten

 

 

 

 

 

4.

The engine is operated above 4,000 feet.

the life of the valves.

 

 

HOW TO START THE ENGINE

3.Make sure the blade rotation control is in the DISENGAGE po- sition.

WARNING: The electrical system has an operator presence system that includes a sensor switch mounted in the seat. These components tell the elec- trical system if the operator is sitting on the seat. This system will stop the engine when the operator leaves the seat. For your protection, always make sure this system operates correctly.

NOTE: The engine will not start unless you depress the clutch/brake pedal, move the shift lever to the neutral (N) position, and move the blade rotation control to the DISENGAGE position.

1.Sit in the middle of the seat. Push the clutch/brake pedal com- pletely forward. Keep your foot on the pedal.

2.Move the shift lever to the neutral (N) position.

4.Move the throttle control completely forward to the CHOKE or FAST position. Some models have a separate choke knob. Pull the choke knob to the full CHOKE position.

5.Turn the ignition key to the START position. Release the key when the engine starts.

NOTE: If the engine does not start after four or five tries, move the throttle control to the FAST position. Again try to start the engine. If the engine will not start, see the

TROUBLE SHOOTING CHART.

6.Slowly move the throttle control to the SLOW position. If model has a separate choke knob, push in the choke knob.

7.Let a cold engine run for several minutes. Begin work when the engine is warm. To start a hot engine, move the throttle control to a position between FAST and SLOW.

HOW TO START WITH A WEAK BATTERY

If the battery is too weak to start the engine, the battery needs to be charged. If “Jumper Cables” are used to start the engine in an emergency, follow the procedure below.

NOTE: The unit is equipped with a 12 volt negative to ground system. Also, the other vehicle must have a 12 volt negative to ground system.

WARNING: Do not smoke. The fumes from the battery acid can cause an explosion. Keep the battery away from any flames or sparks. To prevent sparks, fasten the red “Jumper cable” to the positive (+) terminal be- fore connecting the black “Jumper cable”.

NOTE: If the seat is raised when starting the engine, move the blade rotation control to the DISENGAGED position and engage the parking brake.

1.Connect each end of the RED “Jumper Cable” to the positive

(+) terminals of each battery. Make sure you do not touch the chassis with the cables.

2.Connect one end of the BLACK “Jumper Cable” to the negative

(–) terminal of the charged battery.

3.Connect the other end of the BLACK “Jumper Cable” to the mower’s engine block.

4.Start the engine that has the weak battery last. Allow the engine to run.

5.To disconnect the “Jumper Cables”, reverse the above steps.

F–040700C

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Model Table of Contents OWNER’S Information Responsibility of the OwnerII. Slope operation Safe Mowing Guide Safe Mowing Guide Safe Mowing Guide Steps to Follow Before MowingInternational Pictorials International PictorialsAssembly AssemblyMaintenance Free Battery HOW to Charge the Maintenance Free BatteryHOW to Install the Seat HOW to Assemble the Steering WheelIMPORTANT! Before YOU Start Mowing HOW to Prepare the EngineCheck the Level of the Mower Housing Check the TiresOperation Location of ControlsLift Lever HOW to USE the Throttle Control HOW to USE the Shift LeverAttachments HOW to Stop the Unit HOW to SET the Parking BrakeHOW to Change the Cutting Height HOW to Transport the UnitHOW to Operate with the Mower Housing HOW to Operate the Unit on HillsBefore Starting the Engine HOW to Start the EngineHOW to Start with a Weak Battery CarburetorOperating Tips Mowing and Bagging TipsHOW to Check the Muffler MaintenanceMaintenance Chart General RecommendationsHOW to Remove and Install the Blade HOW to Sharpen the BladeInspect Blade HOW to Adjust the Blade Rotation Control HOW to Check and Adjust the Drive Brake HOW to Check and Adjust the ClutchHOW to Clean the Battery Where to Lubricate HOW to Check the Fuel FilterHOW to Remove the Mower Housing HOW to Install the Mower HousingHOW to Level the Mower Housing Front to Back AdjustmentSide to Side Adjustment HOW to Replace the Motion Drive Belt RemovalHOW to Replace the Mower Drive Belt HOW to Install the Wheels Front WheelHOW to Clean the Mower Housing HOW to Replace the FuseHOW to Replace the Light Bulb BatteryTrouble Shooting Chart Problem The engine will not startBrown & WISER, INC CPT Canada Power Technology LimitedBILLIOU’S, INC Frank Edwards CORepair Parts Chassis & HoodKey Description Repair Parts Motion Drive Motion Drive Steering Key Part Description Mower Housing Suspension Repair Parts Mower Housing Key Description Repair Parts Engine Mount Repair Parts Repair Parts Electrical System Electrical System 040700C 040700C 040700C Index Lawn Tractor Accessories

387002x92NA specifications

The Stanley Black & Decker 387002X92NA is a versatile and innovative tool that stands out in the realm of power tools. Designed for both professionals and DIY enthusiasts, this product exemplifies quality, reliability, and advanced technology. One of the main features of the Stanley Black & Decker 387002X92NA is its high-performance motor, which delivers impressive torque and speed, making it suitable for a wide range of applications. Whether you're drilling into wood, metal, or masonry, this tool offers the versatility required to tackle various projects with ease.

Incorporating cutting-edge technology, the Stanley Black & Decker 387002X92NA is equipped with an electronic control system that optimizes power usage, extending the lifespan of the tool. Additionally, its variable speed settings allow users to adjust the tool's performance to match specific tasks, providing greater control and precision. This feature is particularly beneficial for intricate jobs where accuracy is paramount.

The ergonomic design of the 387002X92NA ensures a comfortable grip, reducing user fatigue during extended use. The lightweight nature of the tool also enhances mobility, making it easy to maneuver in tight spaces. Furthermore, the inclusion of an LED work light illuminates darker work areas, improving visibility and safety while working.

Durability is another hallmark of the Stanley Black & Decker 387002X92NA. Constructed from high-quality materials, the tool is built to withstand rigorous use in demanding environments. Its rugged housing provides resistance against drops and impacts, ensuring longevity even under heavy-duty conditions.

For added convenience, the tool features a quick-change chuck system that enables users to swap out bits rapidly without the need for additional tools. This user-friendly design element enhances efficiency, allowing for seamless transitions between tasks.

In conclusion, the Stanley Black & Decker 387002X92NA is a powerful, durable, and user-friendly tool that integrates advanced technologies and innovative features. Ideal for professionals and hobbyists alike, it excels in performance and versatility, making it a valuable addition to any toolkit. Whether you're embarking on home improvement projects or tackling heavy-duty commercial tasks, this tool delivers the reliability and effectiveness needed to get the job done right.
Top Page Image Contents