Stanley Black & Decker 387002x92NA manual HOW to Check and Adjust the Drive Brake

Page 23

MAINTENANCE

HOW TO CHECK AND ADJUST THE DRIVE BRAKE

Completely push the clutch/brake pedal forward. Set the parking brake. Move the shift lever to the neutral (N) position. Push the unit. If the rear wheels rotate, adjust or replace the brake pads. Adjust the drive brake as follows.

1.The location of the drive brake is on the right side of the gearbox (Figure 16).

2.Make sure the parking brake is set and the shift lever is in neutral (N). Turn the hex nut in a clockwise direction until the rear wheels do not turn when the unit is pushed forward.

3.Release the parking brake and push the unit. If the unit does not roll, turn the hex nut in a counterclockwise direction until the unit rolls.

4.Set the parking brake. Push the unit. If the rear wheels do not turn, the drive brake is correctly adjusted. Release the parking brake.

WARNING: If you cannot correctly adjust the drive brake, replace the brake pads. Correct replacement parts and assistance are available from an autho- rized service center.

Drive Brake

Gearbox

Hex Nut

 

Figure 16

HOW TO CHECK AND ADJUST THE CLUTCH

If the motion drive belt is loose, the clutch will slip when; (1) going up a hill, (2) pulling a heavy load, or (3) the unit will not move forward. Check the clearance at the rear of the pedal (Figure 17). If the motion drive belt is loose, the clearance will be less than 3/16 inch and the clutch will slip. Adjust the clutch as follows.

WARNING: Before you make an inspection, adjust- ment, or repair to the unit, disconnect the wire to the spark plug. Remove the wire from the spark plug to prevent the engine from starting by accident.

1.Check the routing of the motion drive belt. Make sure the belt is installed correctly and is inside all the belt guides.

2.Disconnect the adjustable nut from the lever assembly (Figure 17).

3.Turn the adjustable nut counterclockwise to increase the length of the clutch rod. This adjustment will increase the clear- ance at the pedal and tighten the motion drive belt.

4.Assemble the adjustable nut to the lever assembly. Check the clearance at the pedal.

5.If the pedal cannot be set to 3/16 inch clearance, the motion drive belt has stretched and must be replaced. See “How To Replace The Motion Drive Belt”.

6.If the clutch still slips after the clutch has been adjusted, then the motion drive belt is damaged and must be replaced. See “How To Replace The Motion Drive Belt”.

7.After making an adjustment to the pedal, check the drive brake.

See “How To Check And Adjust The Drive Brake”.

F–040700C

23

Clutch Rod

Pedal

Lever

Assembly

Adjustable Nut (To increase the clearance, turn counterclockwise.)

3/16” (4.7mm)

Clearance

Figure 17

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Model Table of Contents Responsibility of the Owner OWNER’S InformationII. Slope operation Safe Mowing Guide Safe Mowing Guide Safe Mowing Guide Before Mowing Steps to FollowInternational Pictorials International PictorialsAssembly AssemblyHOW to Charge the Maintenance Free Battery Maintenance Free BatteryHOW to Assemble the Steering Wheel HOW to Install the SeatCheck the Tires HOW to Prepare the EngineCheck the Level of the Mower Housing IMPORTANT! Before YOU Start MowingLift Lever OperationLocation of Controls Attachments HOW to USE the Throttle ControlHOW to USE the Shift Lever HOW to Transport the Unit HOW to SET the Parking BrakeHOW to Change the Cutting Height HOW to Stop the UnitHOW to Operate the Unit on Hills HOW to Operate with the Mower HousingCarburetor HOW to Start the EngineHOW to Start with a Weak Battery Before Starting the EngineMowing and Bagging Tips Operating TipsGeneral Recommendations MaintenanceMaintenance Chart HOW to Check the MufflerInspect Blade HOW to Remove and Install the BladeHOW to Sharpen the Blade HOW to Adjust the Blade Rotation Control HOW to Check and Adjust the Clutch HOW to Check and Adjust the Drive BrakeHOW to Clean the Battery HOW to Check the Fuel Filter Where to LubricateHOW to Install the Mower Housing HOW to Remove the Mower HousingSide to Side Adjustment HOW to Level the Mower HousingFront to Back Adjustment Removal HOW to Replace the Motion Drive BeltHOW to Replace the Mower Drive Belt Front Wheel HOW to Install the WheelsBattery HOW to Replace the FuseHOW to Replace the Light Bulb HOW to Clean the Mower HousingProblem The engine will not start Trouble Shooting ChartFrank Edwards CO CPT Canada Power Technology LimitedBILLIOU’S, INC Brown & WISER, INCChassis & Hood Repair PartsKey Description Repair Parts Motion Drive Motion Drive Steering Key Part Description Mower Housing Suspension Repair Parts Mower Housing Key Description Repair Parts Engine Mount Repair Parts Repair Parts Electrical System Electrical System 040700C 040700C 040700C Index Lawn Tractor Accessories

387002x92NA specifications

The Stanley Black & Decker 387002X92NA is a versatile and innovative tool that stands out in the realm of power tools. Designed for both professionals and DIY enthusiasts, this product exemplifies quality, reliability, and advanced technology. One of the main features of the Stanley Black & Decker 387002X92NA is its high-performance motor, which delivers impressive torque and speed, making it suitable for a wide range of applications. Whether you're drilling into wood, metal, or masonry, this tool offers the versatility required to tackle various projects with ease.

Incorporating cutting-edge technology, the Stanley Black & Decker 387002X92NA is equipped with an electronic control system that optimizes power usage, extending the lifespan of the tool. Additionally, its variable speed settings allow users to adjust the tool's performance to match specific tasks, providing greater control and precision. This feature is particularly beneficial for intricate jobs where accuracy is paramount.

The ergonomic design of the 387002X92NA ensures a comfortable grip, reducing user fatigue during extended use. The lightweight nature of the tool also enhances mobility, making it easy to maneuver in tight spaces. Furthermore, the inclusion of an LED work light illuminates darker work areas, improving visibility and safety while working.

Durability is another hallmark of the Stanley Black & Decker 387002X92NA. Constructed from high-quality materials, the tool is built to withstand rigorous use in demanding environments. Its rugged housing provides resistance against drops and impacts, ensuring longevity even under heavy-duty conditions.

For added convenience, the tool features a quick-change chuck system that enables users to swap out bits rapidly without the need for additional tools. This user-friendly design element enhances efficiency, allowing for seamless transitions between tasks.

In conclusion, the Stanley Black & Decker 387002X92NA is a powerful, durable, and user-friendly tool that integrates advanced technologies and innovative features. Ideal for professionals and hobbyists alike, it excels in performance and versatility, making it a valuable addition to any toolkit. Whether you're embarking on home improvement projects or tackling heavy-duty commercial tasks, this tool delivers the reliability and effectiveness needed to get the job done right.
Top Page Image Contents