Shindaiwa X7502824801 Stopping the Engine, When the Engine Starts, Starting a Flooded Engine

Page 12

Starting the Engine (continued)

5.When the engine starts, slowly move the choke lever to the “OPEN” posi- tion. If the engine stops after the initial start, close the choke and restart.

CAUTION!

Do not pull the recoil starter to the end of the rope travel. Pulling the recoil starter to the end of the rope travel can damage the starter.

WARNING!

The cutting attachment may rotate when the engine is started!

WARNING!

Keep all parts of your body away from the rotating cutting attachment and hot surfaces.

IMPORTANT!

If the engine fails to start after several attempts with the choke in the closed

position, the engine may be flooded with fuel. If flooding is suspected, move

the choke lever to the open position and repeatedly pull the recoil starter to remove excess fuel and start the engine. If the engine still fails to start, refer to the troubleshooting section of this manual.

Open

After engine starts, move

choke to OPEN position

When the Engine Starts...

■■After the engine starts, allow the

■■After the engine is warm, pick up

engine to warm up at idle 2 or 3

the unit and clip on the shoulder

minutes before operating the unit.

strap, if so equipped.

Starting A Flooded Engine

1.Slide the ignition switch to the “I” (ON) position.

2.Open the choke, put the throttle lever in the full throttle position, then clear excess fuel from the combustion chamber by cranking the engine several times.

3.If the engine still fails to start or fire, refer to the troubleshooting flow chart at the end of this manual.

Stopping the Engine

Idle the engine briefly before stopping (about 2 minutes), then slide the ignition

switch to the “O” (Engine OFF) position.

CAUTION!

A coasting blade can cause injury while it continues to spin after the engine is stopped or throttle trigger is released. Maintain proper control until the blade has completely stopped rotating.

IMPORTANT!

When the unit is turned off make sure the cutting attachment has stopped before the unit is set down.

■■Squeezing the throttle lever makes the cut- ting attachment move faster; releasing the throttle permits the attachment to stop mov- ing. If the cutting attachment continues to move when the engine returns to idle, car- buretor idle speed should be adjusted (see “Adjusting Engine Idle.”)

OFF

Slide ignition to OFF

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents T282 Trimmer Contents IntroductionSafety Work SafelyStay Alert Use Good JudgmentSafety Labels Properly Equipped OperatorBarefooted Be Aware of the Working Environment 15m50ft Specifications Product DescriptionEmission Control Exhaust & Evaporative EPA 2010 and Later and/or C.A.R.B. TierAssembly Prior to AssemblyFront handle installation Cutting Attachment ShieldAdjust Throttle Lever Free Play Install trimmer headMixing Fuel Fuel RequirementsFilling the fuel tank Mixing InstructionsAfter use Minimize the Risk of FireStarting the Engine When the Engine Starts Stopping the EngineStarting a Flooded Engine Checking Unit Condition OperationCutting grass with a trimmer head Trimmer head stylesMaintenance General maintenanceEngine Operating Speeds Trimming and Mowing GrassDaily Maintenance With cutting attachment installed on gear case LubricationRemove and replace the filter element Muffler and spark arrester maintenance Cooling SystemCarburetor Adjustment Adjusting Engine IdleIdle Speed Adjustment Engine Break-InWear Indicators Long Term StorageTroubleshooting Guide Engine is knocking Poor acceleration Engine stops abruptlyExceptions Purchased Repair Parts and Accessories 01/2010 Page Page Servicing Information Parts/Serial Number

X7502824801 specifications

The Shindaiwa X7502824801 is a powerhouse in the realm of outdoor power equipment, particularly recognized for its outstanding performance and durability. Designed for both professional landscapers and passionate homeowners, this tool exemplifies the quality and innovation that Shindaiwa is renowned for.

One of the key features of the X7502824801 is its robust engine. It is equipped with a high-performance engine that delivers exceptional power while maintaining fuel efficiency. This is vital for users who demand both performance and cost-effectiveness over extended periods of use. The powerful engine ensures that even the most challenging tasks, such as heavy cutting, pruning, and trimming, are accomplished with ease.

Another significant characteristic of the X7502824801 is its lightweight design, which brings an advantage in maneuverability. This feature allows users to work for extended periods without experiencing fatigue, making it especially useful for professionals who rely on their equipment for long hours. The ergonomically designed handle further enhances user comfort, providing a secure grip that reduces vibration during operation.

In terms of technology, the Shindaiwa X7502824801 incorporates advanced features to improve overall efficiency. The unit includes an easy-start system, which minimizes the effort required to start the machine, enabling users to get to work quickly. This is particularly appreciated in commercial settings where time is of the essence.

Additionally, the X7502824801 is designed with low emissions in mind, aligning with modern environmental standards. Its engine technology ensures that it operates cleanly, contributing to a reduction in harmful emissions while maintaining robust performance. This makes it a suitable choice for environmentally conscious users.

The durability of the Shindaiwa X7502824801 cannot be overlooked. Built with high-quality materials, the unit is resistant to wear and tear, ensuring longevity even when subjected to rigorous use. Maintenance is also straightforward, with accessible components that simplify routine checks and repairs.

In summary, the Shindaiwa X7502824801 stands out in the outdoor power equipment market due to its combination of power, comfort, efficiency, and durability. Whether for commercial applications or residential use, this model offers users a reliable and high-performing solution that meets a wide range of landscaping needs. With the integration of cutting-edge technology and smart design, the X7502824801 is a notable investment for anyone serious about outdoor maintenance.
Top Page Image Contents