Shindaiwa 81010 manual Installing a Blade T272X, Assembly and Adjustments, The T272X should now be

Page 9

Installing a Blade T272X

Assembly and Adjustments

Installing a Blade T272X

NOTE:

The T272X is shipped with Holder A, the safety clip, Holder B, shaft bolt, and bolt guard installed. The shaft bolt is a LEFT-

HAND THREAD AND IS REMOVED IN A CLOCKWISE ROTATION!

1. With the gear case output shaft facing

up, rotate the gearshaft and Holder A

until the hole in Holder A aligns with the

matching hole in the gear case ﬂange,

and then lock the holder to the gear

case by inserting the long end of the

hex wrench through both holes.

See Figure 12.

Shaft Bolt

Bolt Guard

Holder B

Safety Clip

	Holder A	Gear Case
	Holder A	Shaft
		Shaft

35010

Hex

Wrench

A

35011

Slide the safety clip off-center.

2.	Remove the shaft bolt, bolt guard and
	Holder B. See Figure 12.
3.	Slide the safety clip off center on the
	gear case shaft. See Figure 12A.
4.	Slide the blade over the safety clip and
	onto the ﬂange on Holder A.
	See Figure 12B.
5.	Lock the blade on the shaft by centering
	the safety clip. See Figure 12C.

CAUTION!

Install the blade so its printed surface is visible to the operator when the brushcutter is in the normal operating position.

B

Slip the blade in place.

35012

Figure 12

C

Center the safety clip.

35013

WARNING!

The blade must ﬁt ﬂat against the holder ﬂange. The blade mounting hole must be centered over the raised boss on blade Holder A.

35014	Install
	Install
	Holder B

Blade

Figure 13

NOTE:

When installing certain blades, it may be nec- essary to temporarily remove the safety clip.

6.Install Holder B on the gear case shaft. See Figure 13.

IMPORTANT!

The machined recess in Holder B must completely surround the safety clip, and both holders must be ﬂat against the sur- face of the blade.

7.Lock Holder A to the gear case by inserting the long end of the hex wrench through both holes as done in step 1 and tighten the shaft bolt securely with the combination spark plug/screwdriver wrench. See Figure 14.

8.Remove the hex wrench.

Tighten the assembly

Combination Spark

Plug/Screwdriver

Wrench

Holder B	35015
	35015
		Bolt Guard
		Blade not shown
Figure 14	Hex Wrench	for clarity.
Figure 14	Hex Wrench
	The T272X should now be
WARNING!	completely assembled to
Never operate the brushcutter without	operate with a blade.
Never operate the brushcutter without
the safety clip installed and both hold-
ers tightly secured and ﬂat against the
blade surface!

9

Image 9

Contents T272 TRIMMER T272X TRIMMER SHINDAIWA OWNER’S/OPERATOR’S MANUALT272 T272X Contents IntroductionAttention Statements Work Safely General Safety Instructions The Properly Equipped OperatorStay Alert Minimize the Risk of FireBe Aware of the Working Environment Safety LabelsFEET T272Prior to Assembly Product DescriptionSpeciﬁcations T272/T272X Adjusting Throttle Level Free Play T272/T272X Assembly and AdjustmentsTo Adjust the Handle Handle T272/T272XSub-Shield T272X when trimmer head is in use Install the Cutting Attachment Shield T272/T272XCutting Attachment Shield To Change Position of Line CutterInstalling a Trimmer Head T272X Installing a Trimmer Head T272Install the Trimmer Head The T272 should nowThe T272X should now be Installing a Blade T272Xcompletely assembled to operate with a bladeFilling the Fuel Tank Mixing FuelStarting the Engine Examples of 501 mixing quantitiesWhen the Engine Starts Engine Idle AdjustmentIdle Speed Adjustment Starting the Engine continuedCheck Unit Condition Using a T272X with a BladeShoulder Strap T272X T272Blade Thrust Using A Brushcutter Blade T272XBrushcutter Handlebar Shoulder StrapDaily Maintenance General Maintenance10-Hour Maintenance 10/15-Hour Maintenance135-Hour Maintenance 50-Hour MaintenanceEvery 50 hours of operation Every 135 hours of operation, removeBlade Sharpening Long Term StorageShindaiwa Tornado Blade Multiple-tooth Circular BladeWhat To Check Troubleshooting GuidePossible Cause RemedyLOW POWER OUTPUT Troubleshooting Guide continuedADDITIONAL PROBLEMS SymptomYour Warranty Rights and Obligations Emission System Warranty StatementOwners Warranty Responsibilities Manufacturer’s Warranty CoverageEmisión de Sistema del Garantía de Declaración por administrada es garantía EstaCubierto Está No Que Propietario del Garantía de ResponsabilidadesADICIONALES PROBLEMAS continuación DIAGNOSTICO GUIARemedio Causa PosibleRemedio POTENCIA BAJACausa Posible Revisar QueDIAGNOSTICO GUIA ARRANCA NO MOTOR ELRevisar Que Plazo Largo de Almacenamiento Discos de AﬁladoMúltiples Dientes de Discos ¡ADVERTENCIAMantenimiento Horas 135 Cada Horas 50 Cada Mantenimientooperación de horas 135 Cada Horas 10 Cada Mantenimiento Horas 10/15 Cada MantenimientoDiario Mantenimiento General MantenimientoVerticales Cortes T272X Disco un UsandoMotor del Operación Desmalezadoras para ArnésUnidad La De Condición La Veriﬁque Nylon de Cabezal con Equipadas Máquinas - Césped de CorteOrillas Césped de Podado y RecorteMotor del Parada Motor del Mínima Marcha de Ajustecontinuación Motor del Arranque ¡ADVERTENCIA! Mínima Marcha de AjusteCombustible de Motor del ArranqueTanque el Llenando ¡PRECAUCIONdisco un con operar para Ajustes y Ensamblajeensamblada completamente ¡ADVERTENCIAT272 Nylon de Cabezal del Instalación T272X Nylon de Cabezal del Instalaciónpodadora como operada ser para ensamblada completamente ahora estar debe T272X LaPRECAUCION Ajustes y EnsamblajePRECAUCIÓN uso en está cabezal el cuandoT272/T272X Acelerador del Palanca la de Holgura la de Ajuste T272/T272X MangoMango el Ajustar Para T272/T272X Especiﬁcaciones Producto del DescripciónEnsamblar de Antes Metros Seguridad de EtiquetasTrabajo de Area del Alerta Esté 3 FiguraEquipado Debidamente Operario El Seguridad deGenerales Instrucciones SIEMPREContenido Seguridad De DeclaracionesIntroducción 81010 part de Numero T272X T2725/05 .Rev