Shindaiwa X7502825601, C254 manual Blade Installation, Install Metal Shield

Page 8

Assembly (continued)

Throttle Linkage and Ignition Leads

Adjust throttle trigger free play

The throttle trigger free play should be approximately 4 - 6 mm (3/16”

-1/4”). Make sure that the throttle lever operates smoothly without binding.

1.Loosen the air cleaner cover knob(s) and remove the air cleaner cover.

2.Place throttle linkage (A) through adjustment fixture (B) and install wire end into large carburetor throt- tle swivel hole (C). Check throttle for freedom of movement and that wide open throttle / low idle extremes are adjusted properly.

4-6 mm (3/16”-1/4”)

Throttle Free Play

Throttle trigger free play

3.Turn the cable adjuster in or out as required to obtain proper free play 4 - 6 mm (3/16 - 1/4 in.).

4.Connect 2 ignition stop leads from throttle cable tubing to 2 ignition leads on engine.

5.Reinstall the air cleaner cover.

Cable

B

A

C

Adjuster

Remove air cleaner cover

Blade Installation

WARNING

You must install the U-Handle and all Blade Conversion parts shown in the following instructions before operating this unit with a metal blade, otherwise serious injury may result.

NOTE:

Model C254includes U-Handle, and necessary blade conversion parts. Blades are not provided with trimmer/brushcutters and must be selected for type of cutting being performed.

Install Metal Shield

Tools Required: 8 x 10 mm Open-end Wrench, Screwdriver, 17x19 mm Wrench, 4 mm Hex Wrench

Parts Required: Metal Shield, Shield Bracket,

3 - 5 x 10 mm screws w/captivated flat and lock- washer, (metal shield to gear housing).

2 - 5 x 8 mm screws, 2 - 5 mm nuts, 2 - 5 mm lock- washers, (bracket to shield).

2 - 5 mm nuts, 2 - 5 mm lockwashers (bracket to gear housing)

1.If installed remove nylon line head, adapter plate, shield plate, and plastic shield.

a.Align locking hole in adapter plate with notch in edge of gear housing and insert locking tool (A).

b.Remove line head (B) by turning it clockwise until head is completely off of shaft.

c.Remove locking tool.

C

A

B

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents C254 Brushcutter Contents IntroductionSafety Safety LabelsWork Safely Stay AlertProperly Equipped Operator Be Aware of the Working EnvironmentSpecifications Product DescriptionAssembly Prior to AssemblyHandlebar Assembly Install the handlebar Emission Control Exhaust & EvaporativeInstall trimmer head Nylon line replacementCutting attachment shield To advance trimmer line TipBlade Installation Install Metal ShieldInstall Blade Mixing Fuel Fuel RequirementsMinimize the Risk of Fire Filling the fuel tankAfter use Starting the Engine Press primer bulbOperation Stopping the EngineChecking Unit Condition Cutting grass with a trimmer head Trimmer head stylesEngine Operating Speeds Trimming and Mowing GrassUsing a blade Blade ThrustBrushcutter Handlebar Brushcutter Shoulder StrapMaintenance Hour maintenance More frequently in dusty conditions 10/15-Hour maintenanceRemove and clean or replace the spark plug Hour maintenance Gearcase lubricationValve Adjustment Hour maintenance Remove and replace the fuel filter elementHour Maintenance Carburetor Adjustment Muffler and spark arrester maintenanceEngine Break-In High Altitude OperationAdjusting Engine Idle Idle Speed AdjustmentBlade Sharpening Multiple-tooth Circular BladeLong Term Storage Troubleshooting Guide Possible CauseIs the engine overheating? Symptom Possible Cause Remedy Exceptions Purchased Repair Parts and Accessories 99922201033 Page Page Page Page T10512001001/T10512999999 Servicing InformationT10611001001/T10611999999

C254, X7502825601 specifications

The Shindaiwa X7502825601 C254 is a robust and versatile brush cutter designed for both professional landscapers and passionate garden enthusiasts alike. Known for its high performance and durability, this powerful tool seamlessly combines advanced technology with user-friendly features, making it a go-to choice for tackling tough jobs.

One of the main features of the Shindaiwa C254 is its impressive engine. Equipped with a 25.4cc two-stroke engine, this brush cutter delivers ample power while remaining lightweight, making it easy to maneuver and handle for extended periods. The engine’s design emphasizes fuel efficiency without compromising performance, allowing users to complete their tasks effectively and save on fuel costs.

The C254 is also recognized for its innovative Easy Start technology. This system minimizes the effort required to start the machine, enabling users to get to work quickly without the frustration of cumbersome starting rituals. The low vibration design significantly enhances comfort, reducing user fatigue during extended use and ensuring increased productivity.

The brush cutter features an ergonomic handle with a comfortable grip, designed with the user in mind. The two-hand operation allows for better control, especially when navigating through dense vegetation or uneven terrain. Its lightweight construction further aids in handling, making it suitable for prolonged use without strain.

In terms of versatility, the Shindaiwa C254 comes equipped with detachable cutting attachments, including a blade and a trimmer head. This allows users to switch between heavy-duty cutting and precise trimming with ease, making it suitable for a wide range of landscaping tasks—from clearing thick brush to edging lawns.

Durability is another hallmark of the C254. Constructed with high-quality materials, this brush cutter is built to withstand the rigors of tough outdoor environments. Additionally, Shindaiwa offers a strong warranty and reliable service options, ensuring peace of mind for users.

In conclusion, the Shindaiwa X7502825601 C254 stands out in the brush cutter market with its powerful engine, user-friendly features, and exceptional versatility. Whether you are a professional landscaper or a dedicated DIY gardener, the C254 offers reliable performance, making yard work more efficient and enjoyable.
Top Page Image Contents