Servis-Rhino 5211 manual Mounting Loader

Page 42

ASSEMBLY

ASSEMBLY

8.Extend lift cylinders 10” to 12” to rotate top of loader uprights forward out of the mount, allowing tractor to be pushed rearward. Retract bucket cylinders until lower loader upright pins clear mount pin saddles and front tires and/or fenders (See Figure Asm-L-0003).

9.Move tractor rearward approximately 6”, being certain not to stretch hydraulic hoses.

10.Stop tractor engine and set parking brake. Relax lift cylinders and bucket cylinders by moving each control lever in both directions. Disconnect hydraulic hoses from tractor.

11.Start tractor engine and release brakes. Slowly back tractor out of loader.

Mounting Loader

Mounting is basically reverse of dismounting.

1.Slowly drive tractor up to loader. Shut off tractor and apply brakes.

2.Connect hydraulic hoses. Make sure couplers are clean before connecting together.

3.Start engine and release parking brake. Make sure lift cylinders are extended 10” to 12”. Stroke bucket cylinders to raise or lower uprights for loader upright pin to clear each front mount pin saddle by approximately 1” (See Figure Asm-L-0003).

4.Drive tractor forward until loader upright pins contact mount vertical stop surfaces just above the mount pin saddles (See Figure Asm-L-0003). Extend bucket cylinders to FULLY seat both loader upright pins into mount pin saddles and raise parking stands off ground. Retract lift cylinders, allowing tractor to move forward. Continue until loader uprights have fully seated into back of mount saddles by retracting lift cylinders to raise tractor front end (tires can be off ground).

5.Stop engine. Allow tractor front end to lower by relaxing ONLY lift cylinders with control lever.

6.Set parking brake. Insert two 1-1/4 x 7” pins and linch pins.

7.Remove linch pins and hitch pins from parking stands, rotate stands into storage position and secure with hitch pins and linch pins.

NOTE: If front wheel spacings were changed while loader was off tractor, tire and fender clearances must be checked and possibly adjusted to insure proper clearances.

5211 01/11

Assembly Section 3-6

© 2011 Alamo Group Inc.

Image 42

Contents 5211 To the Owner/Operator/Dealer Table of Contents Maintenance Section Safety Section Safety General Safety Instructions and Practices5211 01/11 Safety Section Operator Safety Instructions and Practices Equipment Operation Safety Instructions and Practices SG-36 Safety Safety 5211 01/11 Safety Section SL-33 SPU-2 Safety Transporting Safety Instructions and Practices Maintenance and Service Safety Instructions and Practices 5211 01/11 Safety Section See Your Rhino Dealer Storage and Parking Safety Instructions and Practices Concluding Safety Instructions and PracticesDecal Location QTY Level Description Decal Description Loader Positions 5211 01/11 Safety Section Loader Safety Safety Safety Federal Laws and Regulations Page Introduction Section Introduction Introduction Introduction Before Operating this Machine Page Assembly and Connecting the Loader Section Assembly Assembly Instructions5211 01/11 Assembly Section Proper Rear Ballasting and Wheel Spacing Dismounting Loader and Mounting Loader to Tractor Dismounting LoaderMounting Loader Attaching Pin on Bucket Mounting and Dismounting Attachment Mounting Attachment to LoaderDetaching Quick Attach Device Assembling Quick Attach DeviceInstalling Quick Attach Device When Connecting an Attachment to the Loader Quick Hitch Assembly Operation Section Operation Standard Equipment and Specifications Operator Requirements Operation Personal Protective Equipment PPE Tractor Requirements Rops and Seat BeltTractor Lighting and SMV Emblem Getting On and Off the Tractor Tractor BallastBoarding the Tractor Dismounting the TractorStarting the Tractor Pre-Operation Inspection and Service Tractor Pre-Operation Inspection/Service Loader Pre-Operation Inspection and ServiceMount Assembly OPS-L-0007B Do not Operate an Unsafe Tractor or Front END Loader Front END Loader PRE-OPERATION Inspection Driving the Tractor and Loader Operating the Tractor and Loader Driving the Tractor and LoaderSG-36 Operation Operation SL-33 Operation Operating the Loader Filling the BucketOperation Lifting the Load Carrying the Load Dumping the Bucket Lowering the BucketOperating with Float Control Loading from a Bank Operation Peeling and Scraping Loading LOW Trucks or Spreaders from a Pile Backfilling Operation Handling Large Heavy Objects Operating Bale Spear Loader Storage Transporting the Tractor and ImplementShutting Down the Implement Operation Transporting on Public Roadways Operation Hauling the Tractor and Implement Troubleshooting Guide Trouble Possible Cause Possible RemedyPage Maintenance Section Maintenance 5211 01/11 Maintenance Section Lubrication Schedule Daily Maintenance Cylinder Service Lift and Bucket Cylinder DisassemblyAdjusting Bucket Level Indicator Lift and Bucket Cylinder ReassemblyStorage Maintenance Proper Torque for Fasteners Maintenance Maintenance Page Rhino To the OWNER/OPERATOR/DEALER SOM-01/11 F-3738C Printed U.S.A