Servis-Rhino 2410 manual Dismounting Loader and Mounting Loader to Tractor

Page 39

ASSEMBLY

Dismounting Loader and Mounting Loader to Tractor

Dismounting Loader

To avoid injury during installation of loader:

•Place loader bucket against barrier to restrict forward movement of loader.

•Do not permit bystanders within 10 feet of loader.

Loader must be equipped with a bucket or other optional attachment to dismount from tractor.

When dismounting loader, maintain clearance between loader side frames and tractor hood and front axle.

1.Locate tractor and loader on firm level ground.

2.Level and lower bucket to ground. Engage tractor brakes and shut off tractor engine. Move lift control lever back and forth several times to relieve pressure in lift cylinders.

3.Remove 5/8 lock nuts and washers which clamp hinges closed around mid mounting tubes on tractor.

4.Start tractor engine and release tractor brakes. Activate lift control lever to raise side frame up off midmounting assembly. Continue rotating loader side frames off midmounting tubes. Slowly back tractor out of loader while rotating loader side frames. Allow loader to roll off front mounting bracket until lift cylinders are fully extended and yoke is resting on ground. Engage tractor brakes and shut off tractor engine.

5.Move lift and bucket control levers back and forth several times to relieve pressure on lift and bucket cylinders. Disconnect quick couplers between loader and tractor. Hang hoses over loader side frame upright for storage. Make sure male quick couplers will not become contaminated during storage.

6.Fasten bolts, washers and nuts onto hinge for storage.

NOTE: Loader should be stored in a dry place. If loader is being stored for an extended period (one month or more), a coat of grease should be applied to the cylinder shafts to prevent rusting.

2410 02/10

Assembly Section 3-5

© 2010 Alamo Group Inc.

ASSEMBLY

Page 38 Page 40
Image 39
Page 38 Page 40
Contents 2410 To the Owner/Operator/Dealer Table of Contents Maintenance Section Safety Section General Safety Instructions and Practices Safety2410 02/10 Safety Section Operator Safety Instructions and Practices Equipment Operation Safety Instructions and Practices SG-36 2410 02/10 Safety Section Safety SL-33 SPU-2 Safety Transporting Safety Instructions and Practices Maintenance and Service Safety Instructions and Practices Safety Concluding Safety Instructions and Practices Storage and Parking Safety Instructions and PracticesDecal Location QTY Level Description Decal Description Loader Positions 2410 02/10 Safety Section Loader Safety Safety Safety This Act Seeks Federal Laws and RegulationsPage Introduction Section Introduction Introduction Introduction Before Operating this Machine Page Assembly and Connecting the Loader Section Assembly Instructions AssemblyAssembly Proper Rear Ballasting and Wheel Spacing Dismounting Loader and Mounting Loader to Tractor Preparing Stored Loader for Mounting Mounting Loader Attaching Quick Attach Buckets or Round Bale Spear Quick-Attach Round Bale SpearDirt Plate Detaching Quick Attach Buckets or Round Bale SpearAttaching Pin on Bucket, Round Bale Spear or Manure Bucket TinesAssembling Quick Attach Device Installing Quick Attach Device When Connecting an Attachment to the Loader Quick Hitch Assembly Page Operation Section Operation Standard Equipment and Specifications Operator Requirements Operation Personal Protective Equipment PPE Tractor Requirements Rops and Seat BeltTractor Lighting and SMV Emblem Tractor Ballast Getting On and Off the TractorDismounting the Tractor Boarding the TractorStarting the Tractor Tractor Pre-Operation Inspection/Service Pre-Operation Inspection and ServiceLoader Pre-Operation Inspection and Service Mount Assembly OPS-L-0007B Do not Operate an Unsafe Tractor or Front END Loader Front END Loader PRE-OPERATION Inspection Driving the Tractor and Loader Driving the Tractor and Loader Operating the Tractor and LoaderSG-36 Operation Operation SL-33 Operation Filling the Bucket Operating the LoaderOperation Lifting the Load Carrying the Load Lowering the Bucket Dumping the BucketOperating with Float Control Loading from a Bank Operation Peeling and Scraping Loading LOW Trucks or Spreaders from a Pile Backfilling Operation Handling Large Heavy Objects Operating Bale Spear Loader Storage Transporting the Tractor and ImplementShutting Down the Implement Operation Transporting on Public Roadways Operation Hauling the Tractor and Implement Trouble Possible Cause Possible Remedy Troubleshooting GuideProblem Possible Cause Remedy Maintenance Section Maintenance 2410 02/10 Maintenance Section Lubrication Schedule Daily Maintenance Lift and Bucket Cylinder Disassembly Cylinder ServiceLift and Bucket Cylinder Reassembly Storage Maintenance Proper Torque for Fasteners Maintenance Maintenance Page Rhino To the OWNER/OPERATOR/DEALER SOM-02/10 F-3654C Printed U.S.A

2410 specifications

The Servis-Rhino 2410 is a highly regarded piece of equipment in the agricultural sector, particularly known for its efficiency and reliability in land preparation, maintenance, and crop management. This versatile machine stands out for its robust construction and user-friendly design, making it a favorite among farmers and landscapers alike.

One of the main features of the Servis-Rhino 2410 is its exceptional cutting width of 240 inches, which allows operators to cover large areas in a relatively short time. This efficiency not only saves time but also minimizes the cost of fuel and labor, making it an economical choice for large-scale operations.

The 2410 is equipped with advanced rotary cutter technology, enabling it to handle a variety of vegetation types, from thick grasses to dense brush. The rotary blades are designed for optimal performance, ensuring a clean cut and preventing the risk of clogging or jamming, which can lead to downtime. This is particularly important during peak seasons when time is of the essence.

In terms of power, the Servis-Rhino 2410 typically requires a tractor with a minimum horsepower of around 70 to function effectively. This power requirement ensures that the machine can operate under various tough conditions, including hilly terrain and dense vegetation. The robust construction of the 2410 also contributes to its longevity, allowing it to withstand the rigors of agricultural use.

Another significant characteristic of the Servis-Rhino 2410 is its adjustable hitch system, providing flexibility in terms of attachment to different tractor models. This versatility allows the 2410 to be utilized across various farms and applications, enhancing its appeal among users with diverse needs.

Additionally, the 2410 is designed with safety in mind, featuring shielded blades and an overload protection system that minimizes the risk of mechanical failure. The user-friendly controls make it easy for operators to manage the machine, allowing for precise adjustments while maintaining productivity.

Overall, the Servis-Rhino 2410 combines innovative technology with durable construction, making it an exceptional tool for farmers and land managers looking to enhance their productivity while ensuring a high standard of performance. Its combination of efficiency, versatility, and user-friendly design solidifies its position as a leading choice in the agricultural equipment market.
Top Page Image Contents