Servis-Rhino 2410 manual General Safety Instructions and Practices

Page 6
(SG-7)
(SG-3)

SAFETY

SAFETY

General Safety Instructions and Practices

A careful operator is the best operator. Safety is of primary importance to the manufacturer and should be to the owner/operator. Most accidents can be avoided by being aware of your equipment, your surroundings, and observing certain precautions. The first section of this manual includes a list of Safety Messages that, if followed, will help protect the operator and bystanders from injury or death. Read and understand these Safety Messages before assembling, operating or servicing this Implement. This equipment should only be operated by those persons who have read the manual, who are responsible and trained, and who know how to do so responsibly.

The Safety Alert Symbol combined with a Signal Word, as seen below, is used throughout this manual and on decals which are attached to the equipment. The Safety Alert Symbol means: “ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!” The Symbol and Signal Word are intended to warn the owner/operator of impending hazards and the degree of possible injury faced when operating this equipment.

Practice all usual and customary safe working precautions and above all---remember safety is up to YOU. Only YOU can prevent serious injury or death from unsafe practices.

Indicates an imminently hazardous situation that, if not avoided, WILL result in DEATH OR VERY SERIOUS INJURY.

Indicates an imminently hazardous situation that, if not avoided, COULD result in DEATH OR SERIOUS INJURY.

Indicates an imminently hazardous situation that, if not avoided, MAY result in MINOR INJURY.

Identifies special instructions or procedures that, if not strictly observed, could result in damage to, or destruction of the machine, attachments or the environment.

NOTE: Identifies points of particular interest for more efficient and convenient operation or repair.(SG-1)

Si no lee ingles, pida ayuda a alguien que si lo lea para que le traduzca las medidas de seguridad.

Operate this Equipment only with a Tractor equipped with an approved roll- over-protective system (ROPS). Always wear seat belts. Serious injury or even death could result from falling off the tractor--particularly during a turnover when the operator could be pinned under the ROPS.

2410 02/10

Safety Section 1-2

© 2010 Alamo Group Inc.

Page 5 Page 7
Image 6
Page 5 Page 7
Contents 2410 To the Owner/Operator/Dealer Table of Contents Maintenance Section Safety Section Safety General Safety Instructions and Practices2410 02/10 Safety Section Operator Safety Instructions and Practices Equipment Operation Safety Instructions and Practices SG-36 2410 02/10 Safety Section Safety SL-33 SPU-2 Safety Transporting Safety Instructions and Practices Maintenance and Service Safety Instructions and Practices Safety Storage and Parking Safety Instructions and Practices Concluding Safety Instructions and PracticesDecal Location QTY Level Description Decal Description Loader Positions 2410 02/10 Safety Section Loader Safety Safety Safety Federal Laws and Regulations This Act SeeksPage Introduction Section Introduction Introduction Introduction Before Operating this Machine Page Assembly and Connecting the Loader Section Assembly Assembly InstructionsAssembly Proper Rear Ballasting and Wheel Spacing Dismounting Loader and Mounting Loader to Tractor Preparing Stored Loader for Mounting Mounting Loader Quick-Attach Round Bale Spear Attaching Quick Attach Buckets or Round Bale SpearTines Detaching Quick Attach Buckets or Round Bale SpearAttaching Pin on Bucket, Round Bale Spear or Manure Bucket Dirt PlateAssembling Quick Attach Device Installing Quick Attach Device When Connecting an Attachment to the Loader Quick Hitch Assembly Page Operation Section Operation Standard Equipment and Specifications Operator Requirements Operation Personal Protective Equipment PPE Tractor Requirements Rops and Seat BeltTractor Lighting and SMV Emblem Getting On and Off the Tractor Tractor BallastBoarding the Tractor Dismounting the TractorStarting the Tractor Pre-Operation Inspection and Service Tractor Pre-Operation Inspection/ServiceLoader Pre-Operation Inspection and Service Mount Assembly OPS-L-0007B Do not Operate an Unsafe Tractor or Front END Loader Front END Loader PRE-OPERATION Inspection Driving the Tractor and Loader Operating the Tractor and Loader Driving the Tractor and LoaderSG-36 Operation Operation SL-33 Operation Operating the Loader Filling the BucketOperation Lifting the Load Carrying the Load Dumping the Bucket Lowering the BucketOperating with Float Control Loading from a Bank Operation Peeling and Scraping Loading LOW Trucks or Spreaders from a Pile Backfilling Operation Handling Large Heavy Objects Operating Bale Spear Loader Storage Transporting the Tractor and ImplementShutting Down the Implement Operation Transporting on Public Roadways Operation Hauling the Tractor and Implement Troubleshooting Guide Trouble Possible Cause Possible RemedyProblem Possible Cause Remedy Maintenance Section Maintenance 2410 02/10 Maintenance Section Lubrication Schedule Daily Maintenance Cylinder Service Lift and Bucket Cylinder DisassemblyLift and Bucket Cylinder Reassembly Storage Maintenance Proper Torque for Fasteners Maintenance Maintenance Page Rhino To the OWNER/OPERATOR/DEALER SOM-02/10 F-3654C Printed U.S.A

2410 specifications

The Servis-Rhino 2410 is a highly regarded piece of equipment in the agricultural sector, particularly known for its efficiency and reliability in land preparation, maintenance, and crop management. This versatile machine stands out for its robust construction and user-friendly design, making it a favorite among farmers and landscapers alike.

One of the main features of the Servis-Rhino 2410 is its exceptional cutting width of 240 inches, which allows operators to cover large areas in a relatively short time. This efficiency not only saves time but also minimizes the cost of fuel and labor, making it an economical choice for large-scale operations.

The 2410 is equipped with advanced rotary cutter technology, enabling it to handle a variety of vegetation types, from thick grasses to dense brush. The rotary blades are designed for optimal performance, ensuring a clean cut and preventing the risk of clogging or jamming, which can lead to downtime. This is particularly important during peak seasons when time is of the essence.

In terms of power, the Servis-Rhino 2410 typically requires a tractor with a minimum horsepower of around 70 to function effectively. This power requirement ensures that the machine can operate under various tough conditions, including hilly terrain and dense vegetation. The robust construction of the 2410 also contributes to its longevity, allowing it to withstand the rigors of agricultural use.

Another significant characteristic of the Servis-Rhino 2410 is its adjustable hitch system, providing flexibility in terms of attachment to different tractor models. This versatility allows the 2410 to be utilized across various farms and applications, enhancing its appeal among users with diverse needs.

Additionally, the 2410 is designed with safety in mind, featuring shielded blades and an overload protection system that minimizes the risk of mechanical failure. The user-friendly controls make it easy for operators to manage the machine, allowing for precise adjustments while maintaining productivity.

Overall, the Servis-Rhino 2410 combines innovative technology with durable construction, making it an exceptional tool for farmers and land managers looking to enhance their productivity while ensuring a high standard of performance. Its combination of efficiency, versatility, and user-friendly design solidifies its position as a leading choice in the agricultural equipment market.
Top Page Image Contents