Installation

Place machine in a convenient location providing ample support, drainage and room for maintenance.

Remove bolts from pallet to foot bracket. Install rubber feet provided as shown in exploded view.

Location:

The location should protect the machine from damag- ing environmental conditions, such as; wind, rain, and freezing.

1.This machine should be run on a level surface where it is not readily influenced by outside sourc- es such as strong winds, freezing temperatures, rain, etc. It should be located to allow accessibility for refilling of fuel, adjustments and maintenance. Normal precautions should be taken by the op- erator of the machine to prevent moisture from reaching the electrical controls.

2.It is recommended that a partition be made be- tween the wash area and the machine to prevent water spray from coming in contact with the machine. Excess moisture reaching any electric components or electrical controls will reduce ma- chine life and may cause electrical shorts.

3.During installation of the machine, beware of poorly ventilated locations or areas where exhaust fans may cause an insufficient supply of oxygen. Sufficient combustion can only be obtained when there is a sufficient supply of oxygen available for the amount of fuel being burned. If it is necessary to install a machine in a poorly ventilated area, out- side fresh air may have to be piped to the burner and a fan installed to bring air into the machine.

Electrical:

This machine, when installed, must be electrically grounded in accordance to local codes. Check for proper power supply using a volt meter.

Placement:

Do not locate near any combustible material. Keep all flammable material at least 20 feet away.

Allow enough space for servicing the machine.

Local code will require certain distances from floor and walls. (Two feet away from walls should be ad- equate.)

Water Source:

The water source for the pressure washer should be supplied by a minimum 5/8” I.D. garden hose with a city water pressure of not less than 30 PSI. If the water supply is inadequate, or if the garden hose is kinked, the attached pressure washer will run very rough and the burner will not fire.

Connection:

See Component Identification.

Venting:

Adding exhaust vent pipe to your oil fired burner is not recommended because restricted air flow causes carbon build-up, which affects the operation, and in- creases maintenance on the coil. If a stack must be used, refrain from using 90° bends. If the pipe can not go straight up then use only 45° bends and go to the next size pipe.The overall pipe length must not exceed 6 feet in length. The burner air adjustment must be performed after vent pipe is installed. Use a smoke tester for proper air setting.

PRESSURE WASHER OPERATOR’S MANUAL

97-6133 • Rev. 5/07

HP-5030D specifications

The Shark HP-5030D is a powerful and innovative home cleaning tool designed to simplify the process of cleaning while delivering impressive performance. This versatile vacuum is equipped with advanced technology and features that cater to a variety of cleaning needs, making it a favorite among homeowners.

One of the standout features of the Shark HP-5030D is its lightweight and compact design. Weighing in at just a few pounds, this vacuum is easy to maneuver and carry, allowing users to clean without the usual strain associated with heavier models. Its compact size makes it ideal for storage in small spaces, ensuring it can be easily tucked away when not in use.

The Shark HP-5030D is powered by a robust and efficient motor that provides strong suction power, making it effective for both carpet and hard flooring. This vacuum is equipped with a brush roll that is specifically designed to lift dirt and debris from various surfaces, offering a deep clean that is hard to match. The advanced motor technology also ensures quiet operation, allowing users to clean at any hour without disturbing others.

Notably, the Shark HP-5030D features a HEPA filtration system that captures 99.9% of dust and allergens, making it an excellent choice for households with allergies or respiratory concerns. This filtration system is complemented by a washable and reusable filter, reducing the cost of maintenance while promoting sustainability.

Another impressive characteristic is the vacuum’s versatility; it comes with several attachments that cater to different cleaning tasks. The included crevice tool is perfect for tight spaces, while the upholstery tool efficiently cleans furniture and drapes. The vacuum also features a dusting brush, making it capable of tackling delicate surfaces without causing damage.

Moreover, the Shark HP-5030D is designed for ease of use. It features a large capacity dust bin that can easily be emptied with the touch of a button, minimizing mess and making the disposal of dirt and debris simpler than ever. The vacuum also has a convenient one-click transformation into a handheld mode, making it straightforward to reach high or low areas.

In summary, the Shark HP-5030D stands out in the market for its lightweight design, powerful suction, HEPA filtration, and versatile attachments. It combines functionality with ease of use, making it a valuable addition to any cleaning arsenal. Whether it's for everyday cleaning or tackling specific messes, this vacuum is designed to meet the demands of modern households with efficiency and style.