Tanaka TPS2501, TPS-2510, TPS250PF/PN, TPS-270PF/PN Maintenance, Carburetor adjustment Fig

Page 11

TPS-2501,TPS-2510.TPS-250PN,TPS-270PN Owner’s Manual

5. Maintenance

MAINTENANCE, REPLACEMENT, OR REPAIR OF THE

EMISSION CONTROL DEVICES AND SYSTEMS MAY

BE PERFORMED BY ANY NONROAD ENGINE REPAIR

ESTABLISHMENT OR INDIVIDUAL.

Carburetor adjustment (Fig. 3-1)

WARNING!

The cutting attachment may be spinning during carburetor adjustments.

WARNING!

Never start the engine without the complete clutch cover and tube assembled! Otherwise the clutch can come loose and cause personal injuries.

In the carburetor, fuel is mixed with air. When the engine is test run at the factory, the carburetor is basically adjusted. A further adjustment may be required, according to climate and altitude. The carburetor has one adjustment possibility:

T = Idle speed adjustment screw.

Idle speed adjustment (T)

Check that the air filter is clean. When the idle speed is correct, the cutting attachment will not rotate. If adjustment is required, close (clockwise) the T-screw, with the engine running, until the cutting attachment starts to rotate.

Open (counter-clockwise) the screw until the cutting attachment stops. You have reached the correct idle speed when the engine runs smoothly in all positions well below the rpm when the cutting attachment starts to rotate.

If the cutting attachment still rotates after idle speed adjustment, contact your service workshop.

NOTE!

Standard Idle rpm is 2500-3000 rpm.

WARNING!

When the engine is idling the cutting attachment must under no circumstances rotate.

Air filter (Fig. 3-2)

The air filter must be cleaned from dust and dirt in order to avoid:

Carburetor malfunctions.

Starting problems.

Engine power reduction.

Unnecessary wear on the engine parts.

Abnormal fuel consumption.

Clean the air filter daily or more often if working in exceptionally dusty areas.

Cleaning the air filter

Remove the air filter cover and the filter (1).

Rinse it in warm soap suds. Check that the filter is dry before reassembly. An air filter that has been used for some time cannot be cleaned completely. Therefore, it must regularly be replaced with a new one. A damaged filter must always be replaced.

www.tanaka-usa.com

10

custsvc@tanaka-ism.com

Image 11
Contents TPS-250PF/PN,TPS-270PF/PN Before using this unit Custsvc@tanaka-ism.com Operator Safety Drive shaft to engine Assembly proceduresThrottle wire/stop cord Installation of handle FigProper Tension is Extremely IMPORTANT! -11 Installation of bar and chainFueling Operating procedures Fuel FigFuel Chain OIL Fig Adjustment of Chain OIL SupplyStopping Fig Starting FigSafe Operation Pruning techniquesCleaning the air filter MaintenanceCarburetor adjustment Fig Idle speed adjustment TCylinder Engine cooling Fig Chain oil filter -2CSpark plug Fig Muffler FigAngle transmission -4 Oiler port FigGuide bar Fig Side case FigChain Sharpening Monthly maintenance Maintenance scheduleDaily maintenance Weekly maintenanceSpecifications Declaration of conformity

TPS-250PN, TPS2501, TPS-2510, TPS250PF/PN, TPS-270PF/PN, TPS-2510, TPS-2510, TPS-250PF/PN, TPS-270PF/PN, TPS-2501 specifications

The Tanaka TPS series represents a line of advanced technological tools designed for efficient and precision-driven operations across various industrial applications. Among the notable models are the TPS-250PN, TPS-2501, TPS-2510, TPS-250PF/PN, and TPS-270PF/PN. Each model embodies unique features tailored to enhance productivity and user experience.

The TPS-250PN stands out for its robust construction and reliability, making it suitable for heavy-duty tasks. It is equipped with a powerful motor that ensures consistent performance even under demanding conditions. The lightweight design facilitates maneuverability, allowing operators to work with ease over prolonged periods.

The TPS-2501 emphasizes versatility, combining various functionalities into a single unit. It incorporates advanced control technologies, enabling precise adjustments suited for different materials and applications. The intuitive interface enhances user engagement and adaptability, making it an ideal choice for both professionals and novices in various sectors.

Meanwhile, the TPS-2510 showcases an advanced safety mechanism, minimizing risks during operation. Its ergonomic design reduces strain on the user's body, contributing to a safer working environment. Enhanced energy efficiency is another hallmark of the TPS-2510, allowing for extended working hours without excessive energy consumption.

The TPS-250PF/PN model integrates innovative feedback systems that monitor performance in real time. Such technology not only optimizes productivity but also provides valuable data for future operational improvements. This predictive capability helps in reducing downtime and maintenance costs, further enhancing overall efficiency.

On the other hand, the TPS-270PF/PN excels in specialized applications, providing high precision and effectiveness in operations that require meticulous attention to detail. This model is particularly valued in sectors like manufacturing and construction, where exact measurements are crucial.

Overall, the Tanaka TPS series, with its varied models including TPS-250PN, TPS-2501, TPS-2510, TPS-250PF/PN, and TPS-270PF/PN, offers state-of-the-art solutions marked by cutting-edge technologies, user-friendly designs, and enhanced safety features. Whether for heavy-duty tasks or precision operations, these tools are engineered to meet the diverse needs of modern-day industries, reinforcing Tanaka's commitment to quality and innovation.