Tanaka TPS-250PN, TPS-2501 owner manual Starting Fig, Stopping Fig

Page 9

TPS-2501,TPS-2510.TPS-250PN,TPS-270PN Owner’s Manual

Starting (Fig. 2-5)

CAUTION!

Before starting, make sure the cutting attachment does not touch anything.

1 . Set ignition switch (1) to ON position. (Fig. 2-5)

*Push priming bulb (4) several times so that fuel flows through the bulb or return pipe. (if so equipped) (Fig. 2-6,7)

2.With the safety trigger (2) pressed (if so equipped), pull throttle trigger and push throttle lock (3), then slowly release the throttle trigger first, then the safety trigger. This will lock the throttle in starting posi- tion.

3.Set choke lever to CLOSED position (5). (Fig. 2-6,7)

4.Pull recoil starter briskly, taking care to keep the handle in your grasp and not allowing it to snap back.

5.When you hear the engine want to start, return choke lever to RUN position (open). Then pull recoil starter briskly again.

NOTE!

If engine does not start, repeat procedures from 2 to 5.

6.After starting engine, pull throttle trigger to release throttle lock. Then allow the engine about 2-3 minutes to warm up before subjecting it to any load.

NOTE!

Throttle limiter (4) is to adjust maximum opening of throttle. At the factory it is adjusted at its full opening. (Fig. 2-5)

Stopping (Fig. 2-8)

Decrease engine speed and run at an idle for a few minutes, then turn off ignition switch.

WARNING!

A cutting attachment can injure while it continues to spin after the engine is stopped or power control is released. When the unit is turned off, make sure the cutting attachment has stopped before the unit is set down.

www.tanaka-usa.com

8

custsvc@tanaka-ism.com

Image 9
Contents TPS-250PF/PN,TPS-270PF/PN Before using this unit Custsvc@tanaka-ism.com Operator Safety Throttle wire/stop cord Assembly proceduresInstallation of handle Fig Drive shaft to engineProper Tension is Extremely IMPORTANT! -11 Installation of bar and chainOperating procedures Fuel Fig FuelFueling Chain OIL Fig Adjustment of Chain OIL SupplyStopping Fig Starting FigSafe Operation Pruning techniquesCarburetor adjustment Fig MaintenanceIdle speed adjustment T Cleaning the air filterSpark plug Fig Chain oil filter -2CMuffler Fig Cylinder Engine cooling FigGuide bar Fig Oiler port FigSide case Fig Angle transmission -4Chain Sharpening Daily maintenance Maintenance scheduleWeekly maintenance Monthly maintenanceSpecifications Declaration of conformity

TPS-250PN, TPS2501, TPS-2510, TPS250PF/PN, TPS-270PF/PN, TPS-2510, TPS-2510, TPS-250PF/PN, TPS-270PF/PN, TPS-2501 specifications

The Tanaka TPS series represents a line of advanced technological tools designed for efficient and precision-driven operations across various industrial applications. Among the notable models are the TPS-250PN, TPS-2501, TPS-2510, TPS-250PF/PN, and TPS-270PF/PN. Each model embodies unique features tailored to enhance productivity and user experience.

The TPS-250PN stands out for its robust construction and reliability, making it suitable for heavy-duty tasks. It is equipped with a powerful motor that ensures consistent performance even under demanding conditions. The lightweight design facilitates maneuverability, allowing operators to work with ease over prolonged periods.

The TPS-2501 emphasizes versatility, combining various functionalities into a single unit. It incorporates advanced control technologies, enabling precise adjustments suited for different materials and applications. The intuitive interface enhances user engagement and adaptability, making it an ideal choice for both professionals and novices in various sectors.

Meanwhile, the TPS-2510 showcases an advanced safety mechanism, minimizing risks during operation. Its ergonomic design reduces strain on the user's body, contributing to a safer working environment. Enhanced energy efficiency is another hallmark of the TPS-2510, allowing for extended working hours without excessive energy consumption.

The TPS-250PF/PN model integrates innovative feedback systems that monitor performance in real time. Such technology not only optimizes productivity but also provides valuable data for future operational improvements. This predictive capability helps in reducing downtime and maintenance costs, further enhancing overall efficiency.

On the other hand, the TPS-270PF/PN excels in specialized applications, providing high precision and effectiveness in operations that require meticulous attention to detail. This model is particularly valued in sectors like manufacturing and construction, where exact measurements are crucial.

Overall, the Tanaka TPS series, with its varied models including TPS-250PN, TPS-2501, TPS-2510, TPS-250PF/PN, and TPS-270PF/PN, offers state-of-the-art solutions marked by cutting-edge technologies, user-friendly designs, and enhanced safety features. Whether for heavy-duty tasks or precision operations, these tools are engineered to meet the diverse needs of modern-day industries, reinforcing Tanaka's commitment to quality and innovation.