McIntosh C2300 owner manual Input Source Settings, Re-Title Inputs, Meter Illumination On/Off

Page 12

2.Press the SETUP Push-button to access the Setup Mode.

3.Rotate the MENU (INPUT) Control until “TRIM TUN 0.0” appears on the Front Panel Alphanumeric Display. Refer to figure 4.

Figure 4

Note: If necessary, rotate the SELECT 1 (TRIM SELECT) Control for “TUN” and rotate the SELECT 2 (TRIM ADJUST) for ”0.0”.

4.Rotate the SELECT 1 Control or use the Remote Con- trol ◄INPUT► push-button until the display indi- cates “TRIM CD 0.0”.

5.Rotate the SELECT 2 Control or use the Remote Control LEVEL or Push-buttons until Listening Volume Level of the CD Input is the same as the Tuner Volume Level. The figure 5 illustration indicates a -2.5dB decrease in the CD Level.

Figure 5

6.Rotate the SELECT 1 Control until the name of the next Input to be adjusted is displayed.

7.Repeat steps 5 and 6 until all the Inputs with sources connected to the C2300 have the same relative volume levels when switching between them. Record any changes made to the various inputs from the default settings in the “Input Source Settings” chart below.

8.Press the SETUP Push-button to exit the Setup Mode.

Input Source Settings

Default Title

New Title

Trim

Trigger

TUNER

DVD

D/A

CD

CDR

SERVER

MC PHONO

MM PHONO

Re-Title Inputs

The C2300 provides the ability to change the default Input Titles to match the components in your system. In the following example the CDR Input will be renamed and ap- pear as AUX on the Front Panel Alphanumeric Display.

Notes: 1. One of the high level Inputs may be renamed to AUX or swiched Off. If any input is switched Off its name will no longer appear on the Front Panel Alphanu- meric Display when using the INPUT Control, nor is it accessible with the Remote Control.

2.When a high level input is switched Off its name will become available to the remaining high level inputs.

3.The Phono MC and Phono MM Inputs are designed for connection of a turntable only and thus the title is not changeable. However, the Phono Input may be switched Off.

1.Press the SETUP Push-button to access the Setup Mode.

2.Rotate the MENU Control until “INPUT 3 TUN” appears on the Front Panel Alphanumeric Display.

3.Rotate the SELECT 1 Control until “INPUT 7

CDR” appears on the Front Panel Alphanumeric Dis- play. Refer to figure 6.

Figure 6

3. Rotate the SELECT 2 Control until the Front Panel Alphanumeric Display indicates “INPUT 7 AUX”. Refer to figure 7.

Figure 7

4. Press the SETUP Push-button to exit the Setup Mode.

Meter Illumination On/Off

The Front Panel Meter Illumination may be switched On or Off. Follow the steps below to switch the Meter Illumina- tion Off.

1.Press the SETUP Push-button to access the Setup Mode.

2.Rotate the MENU Control until the words METER ON appears.

3.Rotate the SELECT 2 Control until the Front Panel Alphanumeric Display indicates “METER OFF”.

4.Press the SETUP Push-button to exit the Setup Mode.

12

Image 12
Contents Tube Preamplifier Important Safety Instructions Customer Service Table of ContentsThank You Please Take a MomentXLR Connectors Power Control and Trigger ConnectorsData Port Connectors Introduction and C2300 Features C2300 FeaturesDimensions Installation Rear Panel Connections How to Connect the C2300 Trim Select Trim Adjust Front Panel Displays, Controls, Push-buttons and JackSetup How to Operate the Setup Modes Default SettingsTrim Level Adjustment Firmware VersionInput Source Settings Re-Title InputsMeter Illumination On/Off Setup, con’t Display Brightness Power Control TriggersAccessory Power Control Tube LEDRemote Control Push-Buttons How to use the Remote Control How to Operate the C2300 Power OnVolume Control Source SelectionBass How to Operate the C2300, con’t Tone BypassMono Record MonitorHeadphones Jack How To Make a RecordingReset of Microprocessors Output 1Silent Audio Switching Volume AdjustmentsTechnical Description Phono CircuitryPower Supply Circuits Meter and CircuitrySpecifications Packing Instructions McIntosh Laboratory, Inc Chambers Street Binghamton, NY
Related manuals
Manual 2 pages 6.61 Kb