f.Never overfill the fuel tank. Fill tank to no more than 1/2 inch below bottom of filler neck to provide space for fuel expansion.
g.Replace gasoline cap and tighten securely.
h.If gasoline is spilled, wipe it off the engine and equipment. move machine to another area. Wait 5 minutes before starting the engine.
i.Never store the machine or fuel container inside where there is an open flame, spark or pilot light as on a water heater, space heater, furnace, clothes dryer or other gas appliances.
j.Allow machine to cool 5 minutes before storing.
Operation
1.Before starting this machine, review the “Safety Instructions”. Failure to follow these rules may result in serious injury to the operator or bystanders.
2.Never leave this machine unattended with the engine running.
3.Do not operate machine while under the influence of alcohol, drugs, or medication.
4.Never allow anyone to operate this machine without proper instruction.
5.Always operate this machine with all safety equipment in place and working. Make sure all controls are properly adjusted for safe operation.
6.Do not change the engine governor settings or overspeed the engine. The governor controls the maximum safe operating speed of the engine.
7.When loading a log, always place your hands on the sides of the log, not on the ends, and never use your foot to help stabilize a log. Failure to do so, may result in crushed or amputated fingers, toes, hand, or foot.
8.Use only your hand to operate the controls.
9.Never attempt to split more than one log at a time unless the ram has fully extended and a second log is needed to complete the separation of the first log.
10.For logs which are not cut square, the least square end and the longest portion of the log should be placed toward the beam and wedge, and the square end placed toward the end plate.
11.When splitting in the vertical position, stabilize the log before moving the control. Split as follows:
a.Place log on the end plate and turn until it leans against the beam and is stable.
b.When splitting extra large or uneven logs, the log must be stabilized with wooden shims or split wood between the log and end plate or ground.
12.Always keep fingers away from any cracks that open in the log while splitting. They can quickly close and pinch or amputate your fingers.
13.Keep your work area clean. Immediately remove split wood around the machine so you do not stumble over it.
14.Never move this machine while the engine is running.
15.This machine should not be towed on any street, highway or public road without checking the existing federal, state, or local vehicle requirements. Any licensing or modifications such as taillights, etc., needed to comply, is the sole responsibility of the purchaser. If a “Statement of Origin” is required in your state, see your local dealer.
16.Do not tow machine faster than 45mph.
17.See Transporting the Log Splitter section in this manual for proper towing instructions once all federal, local, or state requirements are met.
Maintenance and Storage
1.Stop the engine, disconnect the spark plug and ground it against the engine before cleaning, or inspecting the machine.
2.Stop the engine and relieve hydraulic system pressure before repairing or adjusting fittings, hoses, tubing, or other system components.
3.To prevent fires, clean debris and chaff from the engine and muffler areas. If the engine is equipped with a spark arrester muffler, clean and inspect it regularly according to manufacturers instructions. Replace if damaged.
4.Periodically check that all nuts and bolts, hose clamps, and hydraulic fittings are tight to be sure equipment is in safe working condition.
5.Check all safety guards and shields to be sure they are in the proper position. Never operate with safety guards, shields, or other protective features removed.
6.The pressure relief valve is preset at the factory. Do not adjust the valve.
7.Never attempt to move this machine over hilly or uneven terrain without a tow vehicle or adequate help.
8.For your safety, replace all damaged or worn parts immediately with original equipment manufacturer’s (O.E.M.) parts only. “Use of parts which do not meet the original equipment specifications may lead to improper performance and compromise safety!”
9.Do not alter this machine in any manner, alterations such as attaching a rope or extension to the control handle, or adding to the width or height of the wedge may result in personal injury.
Your Responsibility
Restrict the use of this power machine to persons who read, understand and follow the warnings and instruc- tions in this manual and on the machine. Always follow directions on safety labels found on your equipment.
2
Safe
Operation
Practices
WARNING
This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this man- ual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol -
HEED ITS WARNING
Your
Responsibility
Restrict the use
of this power machine to persons who read, understand
and follow the warnings
and instructions in this manual.
5