MTD 607 manual Lower Drive Belt, Front of Tractor

Page 20

Lower Drive Belt

NOTE: Proper removal of the lower drive belt requires the removal of several tractor components. Read through the following procedure prior to attempting it to determine if you feel you could successfully complete it. If you don’t, see an authorized MTD service dealer to have the belt changed.

IMPORTANT: Note the routing of the lower drive belt around both the pulleys and the belt keepers BEFORE performing the following steps.

Locate the variable-speed pulley by looking through the battery tray opening. See Figure 16.

Remove the variable-speed pulley by loosening the hex bolt that secures it to the transmission. Use a second wrench to hold the hex nut on the bottom side of the pulley.

Slide the belt off of the variable-speed pulley as you lift the pulley up and out through the battery tray opening.

Variable-speed

 

 

 

 

 

 

Battery Tray

 

 

 

 

 

 

Shift Lever

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Drive belt (Lower)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Opening

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Pulley

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Rear Idler Pulley

 

 

 

 

Drive belt (Upper)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Belt Keeper

Front Idler Pulley

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Engine Pulley

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Idler Bracket

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Belt Keeper

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

to drive pedal

Double-Idler Bracket

Transmission Idler Pulley

Single-speed

Transmission

Transmission Pulley

Front of Tractor

 

NOTE: View shown from above tractor.

 

Figure 16

Remove the hex bolt from the center of the engine pulley. See Figure 17.

Lower the engine pulley far enough to be able to remove the upper drive belt from around it.

IMPORTANT: When remounting the engine pulley, torque the center hex bolt to between 38 foot- pounds and 50 foot-pounds.

Remove the drive belt by feeding it from both ends toward the front idler pulley on the double-idler bracket. See Figure 16.

Reassemble by following the above steps in reverse order.

Reroute the new belt around the pulleys and belt keepers EXACTLY as the old one was

routed. Refer to Figure 16.

The drive pedal is properly adjusted when the hole found in the double-idler bracket has approximately 1-3/8" of travel with ten pounds of pressure applied to the drive pedal. See Figure 17.

20

Image 20
Contents Important Read Safety Rules and Instructions Carefully OPERATOR’S ManualTable of Contents Finding Your Model NumberMTD Products INC Calling Customer SupportImportant Safe Operation Practices General OperationService Slope OperationDo not ChildrenSafety Labels found on your unit Slope Gauge USE this page AS a Guide toAttachments & Accessories Attaching the Battery CablesTractor SET-UP GAS and OIL FILL-UPControls Ignition Switch Systems Indicator MonitorThrottle Control Lever Choke ControlPTO Power TAKE-OFF Lever Lift LeverDrive Pedal Parking Brake ButtonSafety Interlock Switches Setting the Cutting HeightOperation Starting the EngineStopping the Engine Driving the TractorDriving on Slopes Operating the HeadlightsAdjustments Using the Lift LeverEngaging the PTO Power TAKE-OFF Lever MowingFront to Rear Side to Side Seat AdjustmentSide to Side Brake Adjustment Steering AdjustmentMaintenance Carburetor AdjustmentCleaning the Engine and Deck EngineFront of Tractor Cutting Deck RemovalLift Changing the Deck Belts Inch decksChanging the Transmission Drive Belts Upper Drive BeltLower Drive Belt Cutting Blades Lubrication Troubleshooting Guide Trouble Possible Corrective Action CausesModels 607, 608 Part DescriptionElectrical System Green BlueModels 607 Tractor Body Model Dash Panel Models 607, 608 Lift Assembly 3126 Steering Assembly 4413 Drive System 31 30 12c Single-speed Transmission Hook spring, Ref , here PTO belt for 42 deck shown Power Take-off System Inch Deck Brake Assembly Cutting Decks Briggs & Stratton OHV V-Twin Engine Accessories Briggs & Stratton Opposed TwinMANUFACTURER’S Limited Warranty

607 specifications

The MTD 607 is an advanced piece of machinery designed for a variety of agricultural and landscaping applications. Known for its robust performance and durability, the MTD 607 stands out due to its careful engineering and innovative technologies that cater to the needs of modern users.

One of the key features of the MTD 607 is its powerful engine. This model typically boasts an engine with high torque output, providing the necessary strength for tackling tough terrain and dense vegetation. This allows users to perform a wide range of tasks, from mowing larger areas to managing challenging landscapes efficiently. Its engine is not only powerful but also designed to be fuel-efficient, ensuring that users can rely on the machine for extended periods without frequent refueling.

The MTD 607 incorporates cutting-edge technology to enhance user experience and improve productivity. For instance, it features an intuitive control panel that puts all necessary functions at the operator's fingertips. This means operators can easily adjust settings, monitor performance, and manage tasks without having to navigate through complicated systems. Additionally, some models include digital displays that provide real-time feedback regarding speed, operating hours, and maintenance requirements, ensuring optimal performance at all times.

Comfort is another important aspect of the MTD 607. The design prioritizes ergonomic features, featuring adjustable seats and easy-access controls that cater to users of all sizes. This focus on comfort helps reduce fatigue during prolonged use, allowing operators to work more efficiently over longer periods. Moreover, the MTD 607 is built with a sturdy frame and reinforced components that contribute to its longevity, making it a reliable choice for both commercial and residential users.

Safety is paramount in the design of the MTD 607. It includes multiple safety features such as automatic shut-off mechanisms, reinforced guards, and intuitive braking systems. These features work together to provide peace of mind for operators, ensuring safe operation even in challenging conditions.

In conclusion, the MTD 607 is a versatile and powerful machine with a range of features that make it suitable for various applications in agriculture and landscaping. From robust engines and user-friendly technology to ergonomic designs and safety enhancements, it provides an excellent solution for those seeking efficiency and reliability in their outdoor tasks. Whether for professional landscaping services or personal gardening efforts, the MTD 607 is a worthy investment for enhancing productivity and achieving excellent results.