MTD 607 manual Lubrication

Page 22

It is extremely important that each cutting blade edge be ground equally to maintain proper blade balance. An unbalanced blade will cause excessive vibration when rotating at high speeds, may cause damage to the tractor and result in personal injury. The blade can be tested by balancing it on a blade balancer or round shaft screwdriver. Grind metal from the heavy side until it balances evenly.

When replacing the blade, be sure to install the blade with the side of the blade marked ‘‘Bottom’’ (or with a part number stamped in it) facing the ground when the mower is in the operating position.

IMPORTANT: Use a torque wrench to tighten the blade spindle hex flange nut to between 70 foot- pounds and 90 foot-pounds.

TIRES

The recommended operating tire pressure is approximately 10 psi for the rear tires and 14 psi for the front tires. Refer to the tire sidewall for exact tire manufacturer’s recommended psi. Do not overinflate. Uneven tire pressure could cause the cutting deck to mow unevenly.

BATTERY

The battery is sealed and is maintenance-free. Acid levels cannot be checked.

•Always keep the battery cables and terminals clean and free of corrosive build-up.

•After cleaning the battery and terminals, apply a light coat of petroleum jelly or grease to the terminals and over the positive terminal boot.

•Always keep the boot positioned over the positive terminal to prevent shorting.

IMPORTANT: If removing the battery for any reason, disconnect the NEGATIVE (Black) wire from it’s terminal first, followed by the POSITIVE (Red) wire. When re-installing the battery, always connect the POSITIVE (Red) wire its terminal first, followed by the NEGATIVE (Black) wire. Be certain that the wires are connected to the correct terminals, reversing them could change the polarity and cause damage to your engine’s alternating system.

Charging

If the unit has not been put into use for an extended period of time, charge the battery with an automotive-type 12-volt charger for a minimum of one hour at six amps.

WARNING: Batteries give off an explosive gas during and for some time after charging. Charge battery in a well ventilated area and do not allow a spark or an open flame near the battery.

FUSE

A fuse is installed in your tractor’s wiring harness to protect the tractor’s electrical system from damage caused by excessive amperage. Always use the same capacity fuse for replacement. If the electrical system does not function, or your tractor’s engine will not crank, first check to be certain that the fuse has not blown. It can be found under the hood mounted behind the top of dash panel on the support bar. Pull the fuse out and compare it with Figure 21 to determine if it is good or bad.

GOOD BAD

Figure 21

SECTION 11: LUBRICATION

WARNING: Always stop the engine and disconnect the spark plug wire(s) and ground against the engine before performing any maintenance.

ENGINE

Lubricate the engine with motor oil as instructed in the separate engine manual packed with your unit.

LINKAGE

Lubricate all the pivot points on the drive, brake and lift linkage at least once a season with SAE 30 engine oil.

WHEELS

Both the front wheels and the rear wheels should be removed from the axles once a season. Lubricate the axles and the rims well with an all-purpose automotive grease before re-installing them.

STEERING GEAR

Lubricate the teeth of the steering gear with an all- purpose automotive grease every 25 hours of operation or once a season.

PIVOT POINTS

Lubricate all pivot points (drive pedal, brake pedal, etc.) at least once a season with light oil.

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Important Read Safety Rules and Instructions Carefully OPERATOR’S ManualMTD Products INC Table of ContentsFinding Your Model Number Calling Customer SupportImportant Safe Operation Practices General OperationDo not ServiceSlope Operation ChildrenSafety Labels found on your unit Slope Gauge USE this page AS a Guide toTractor SET-UP Attachments & AccessoriesAttaching the Battery Cables GAS and OIL FILL-UPControls Throttle Control Lever Ignition SwitchSystems Indicator Monitor Choke ControlDrive Pedal PTO Power TAKE-OFF LeverLift Lever Parking Brake ButtonOperation Safety Interlock SwitchesSetting the Cutting Height Starting the EngineDriving on Slopes Stopping the EngineDriving the Tractor Operating the HeadlightsEngaging the PTO Power TAKE-OFF Lever AdjustmentsUsing the Lift Lever MowingSide to Side Seat AdjustmentFront to Rear Side to Side Brake Adjustment Steering AdjustmentCleaning the Engine and Deck MaintenanceCarburetor Adjustment EngineLift Cutting Deck RemovalFront of Tractor Changing the Deck Belts Inch decksChanging the Transmission Drive Belts Upper Drive BeltLower Drive Belt Cutting Blades Lubrication Troubleshooting Guide Trouble Possible Corrective Action CausesModels 607, 608 Part DescriptionElectrical System Green BlueModels 607 Tractor Body Model Dash Panel Models 607, 608 Lift Assembly 3126 Steering Assembly 4413 Drive System 31 30 12c Single-speed Transmission Hook spring, Ref , here PTO belt for 42 deck shown Power Take-off System Inch Deck Brake Assembly Cutting Decks Briggs & Stratton OHV V-Twin Engine Accessories Briggs & Stratton Opposed TwinMANUFACTURER’S Limited Warranty

607 specifications

The MTD 607 is an advanced piece of machinery designed for a variety of agricultural and landscaping applications. Known for its robust performance and durability, the MTD 607 stands out due to its careful engineering and innovative technologies that cater to the needs of modern users.

One of the key features of the MTD 607 is its powerful engine. This model typically boasts an engine with high torque output, providing the necessary strength for tackling tough terrain and dense vegetation. This allows users to perform a wide range of tasks, from mowing larger areas to managing challenging landscapes efficiently. Its engine is not only powerful but also designed to be fuel-efficient, ensuring that users can rely on the machine for extended periods without frequent refueling.

The MTD 607 incorporates cutting-edge technology to enhance user experience and improve productivity. For instance, it features an intuitive control panel that puts all necessary functions at the operator's fingertips. This means operators can easily adjust settings, monitor performance, and manage tasks without having to navigate through complicated systems. Additionally, some models include digital displays that provide real-time feedback regarding speed, operating hours, and maintenance requirements, ensuring optimal performance at all times.

Comfort is another important aspect of the MTD 607. The design prioritizes ergonomic features, featuring adjustable seats and easy-access controls that cater to users of all sizes. This focus on comfort helps reduce fatigue during prolonged use, allowing operators to work more efficiently over longer periods. Moreover, the MTD 607 is built with a sturdy frame and reinforced components that contribute to its longevity, making it a reliable choice for both commercial and residential users.

Safety is paramount in the design of the MTD 607. It includes multiple safety features such as automatic shut-off mechanisms, reinforced guards, and intuitive braking systems. These features work together to provide peace of mind for operators, ensuring safe operation even in challenging conditions.

In conclusion, the MTD 607 is a versatile and powerful machine with a range of features that make it suitable for various applications in agriculture and landscaping. From robust engines and user-friendly technology to ergonomic designs and safety enhancements, it provides an excellent solution for those seeking efficiency and reliability in their outdoor tasks. Whether for professional landscaping services or personal gardening efforts, the MTD 607 is a worthy investment for enhancing productivity and achieving excellent results.
Top Page Image Contents