Marathon F200060 manual Parameter Name Selection Units or Options Range Default, Process Type

Page 8

Table 1 Process Parameters

Parameter Name

Selection

Units or Options

Range

 

Default

 

 

PROCESS TYPE

%O2

CARBON, DPT,

 

 

 

%O2, MV

 

CARB PROC FACT

150

 

0 to 1000

DEWPT PROC FACT

150

 

0 to 1000

OXYGEN EXPON

0002

POWER OF TEN

0 to 31

TC TYPE

B

B, C, E, J, K, N,

 

 

 

NNM, R, S, T

 

Process Type

Selecting the process type determines what type of calculation the Smart Transmitter is going to do based on the probe millivolt and probe temperature inputs. The default process value for the Smart Transmitter is %O2 with an exponent selection of 2. This is the selection most often used in Boiler control and Combustion applications.

Percent Carbon and dew point are typically processes that are used in steel treating applications. Percent Carbon is the process value most often used for the control of case depth or the percent of carbon in a steel hardening furnace. Dew Point is used in the control for endothermic generators.

Carbon Process Factor

The carbon process factor can be used to adjust the % carbon value. This number takes into account a number of assumptions that the carbon value is based on. Primary among these is the assumed level of CO in the atmosphere. See the Theory of Process Calculation section for a complete explanation of this value.

It maybe necessary to change the apparent furnace carbon as measured by the oxygen probe if this value is different than actual load samples, shim stocks, or gas analysis. The basic rule of thumb is that an increase is the carbon process factor will decrease the apparent carbon level in the furnace. The default value is 150. Typical values can very from 50 to 400. Increase or decrease the process factor until the desired carbon level is achieved. A process factor that is drastically different than normal may be an indication of a failing probe, water or air leak in the furnace, or excess methane present. Refer to probe troubleshooting guides to determine what other factors maybe effecting the carbon value.

Dew Point Process Factor

The dew point process factor is similar to the carbon process factor but is used to adjust the dew point value if dew point is selected as the process value. This number takes into account a number of assumptions that the dew point value is based on. Primary among these is the assumed level of hydrogen in the atmosphere. See the Theory of Process Calculation section for a complete explanation of this value.

Page 5 of 23

11/14/2006

Rev. 14

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Marathon Sensors Inc Oxymit Transmitter Operators ManualCopyright Marathon Sensors INC Table of Contents F840031 Typical Oxygen Transmitter Calibration F840030Typical Carbon Transmitter Calibration Block Diagram General DescriptionSafety Summary ConnectionsProcess Parameters Parameter SelectionsGrounding and Shielding Parameter Name Selection Units or Options Range Default Process TypeCarbon Process Factor Dew Point Process FactorAnalog Output Channels Oxygen ExponentTC Type Calibration Process Variable Calculations Percent OxygenPercent Carbon DewpointRTU Framing CommunicationsModbus Error Check Field CRC Address FieldFunction Field Data FieldCRC Memory Map LOW Byte Input Event Upper Byte Load LineLOW Byte Cold Junction Trim High Byte Host AddressBits 0 4 Oxygen Exponent Bits 5 6 Display Decimal PlaceBits 8 12 Redox Metal Number LOW BYTE, Analog OutputHEX DEC Block Parameter Description READ/WRITE High BYTE, Analog OutputAOUTRN1 Analog Output 1 Range READ/WRITE AOUTOF2 Analog Output 2 Offset READ/WRITETemp Measured Temperature Read only Spare READ/WRITE TempfilBlock HEX DEC Parameter Description READ/WRITE Mvfil Coldjct Cold Junction Read onlySpare 800 3000 Operational SpecificationsPercent oxygen 20.9% default Immunity as specified by EN Address 1 is defaultCertifications and Compliance Pending Emissions as specified by EN

F200060 specifications

The Marathon F200060 is a high-performance electric skateboard that has rapidly gained recognition among both enthusiasts and casual riders alike. Combining cutting-edge technology with robust design, this skateboard is engineered to deliver an exhilarating riding experience.

One of the standout features of the Marathon F200060 is its powerful motor system. The skateboard is equipped with a dual-motor setup that offers impressive torque and acceleration, allowing riders to reach a top speed of up to 25 miles per hour. This feature makes it suitable for both commuting and leisurely rides, ensuring a thrilling experience on every journey. The motor system is also designed to be energy-efficient, offering extended battery life and reducing the need for frequent recharging.

Speaking of battery life, the Marathon F200060 boasts a high-capacity lithium-ion battery that can provide a range of up to 20 miles on a single charge. This feature is particularly beneficial for urban commuters, enabling them to travel long distances without the anxiety of running out of power. Additionally, the skateboard supports fast charging technology, allowing riders to recharge the battery in a matter of hours.

The construction of the F200060 is another aspect that sets it apart from its competitors. It features a sturdy, lightweight deck made from high-quality materials, providing both durability and stability. The skateboard's design includes high-grade wheels and advanced shock absorption systems that enhance ride comfort, making it effective for both smooth pavements and rough urban terrains.

In terms of safety, the Marathon F200060 is equipped with integrated LED lights that improve visibility during night rides. The skateboard also features advanced braking systems that allow for smooth and controlled stops, ensuring rider safety on all terrains.

Finally, the F200060 comes with smart technology integration, including Bluetooth connectivity that allows riders to connect their smartphones. Users can monitor battery life, customize settings, and even track their riding statistics through a dedicated app. This integration enhances the overall user experience and provides valuable data to help riders optimize their performance.

In summary, the Marathon F200060 electric skateboard embodies a blend of power, efficiency, safety, and smart technology, making it an excellent choice for anyone looking to elevate their ride. Its performance features and innovative design cater to the needs of modern riders, ensuring countless hours of enjoyment on the road.
Top Page Image Contents