Multiquip BG113BC manual Setup/Operation, Applying Power, Shutdown

Page 20

SETUP/OPERATION

DANGER - HIGH VOLTAGE POWER LINES

When raising mast, ALWAYS be on the lookout for overhead obstructions such as high voltage power lines.The possibility exists of electrocution, even death! if the GloBug comes in contact with high voltage power lines.

Applying Power

1.Make sure the power ON/OFF switch (Figure 13) located near the bottom of the mast is in the OFF position.

ON

OFF

4.Notice that the balloon envelope will begin to deploy as soon as power is applied by an active generator. This function is not controlled by the power ON/OFF switch.

5.Wait until the balloon is fully deployed before attempting to turn on the lamp. The possibility exists of the balloon getting burned (touching the lamp).

6.If the balloon is fully deployed, place the GloBug's ON/ OFF switch (15) in the ON position.

ON

OFF

Figure 15. Power OFF/ON Switch (ON Position)

Figure 13. Power OFF/ON Switch (OFF Position)

CAUTION - READ GENERATOR MANUAL

Before attempting to operate the generator, READ the entire operation section of the manual. Failure to read manual could cause severe damage to the equipment and bodily harm to the operator.

2.The GloBug has a power requirement of 120 VAC, 60 Hz @ 9.6 amps. Connect the GloBug's AC power cord to the 120 VAC twist-lock receptacle (Figure 14) on the the supplied generator.

Figure 14. 120 VAC Receptacle

3.Start the generator as referenced in the "Start-up Section" of the supplied generator manual.

7.The lamp should now be on. If the lamp is not on, check all connections and repeat steps 1 through 6. If the lamp still does not come on contact the MQ service department.

Shutdown

1.Place the power ON/OFF switch (Figure 16) in the OFF position.

ON

OFF

Figure 16. Power OFF/ON Switch (OFF Position)

CAUTION - LAMP COOL DOWN

Allow a sufficient amount of time (15-20 minutes) for the lamp (Figure 17) to cool down before turning off

generator. The possibility exists of the balloon getting burned (touching the lamp).

2.Disconnect the GloBug's AC power cable from the generator. The balloon should begin to deflate.

3.Shutdown generator as referenced in the "Shutdown Section" of the supplied generator manual.

PAGE 20 — GB113BC GLOBUG LIGHTING SYSTEM — OPERATION AND PARTS MANUAL — REV. #5 (01/16/12)

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Model GB113BC Proposition 65 Warning Page Table of Contents Parts Ordering Procedures Ordering parts has never been easierSafety Information Result in injury to yourself and others„ Always know the location of the nearest fire extinguisher„ Never attempt service on a running machine „ Never unplug the lamp’s AC power cable during operationGenerator Safety „ Always make sure the area aboveLoading and Unloading Specifications SpecificationsDimensions TOP View Side View Stow Position Rear ViewFloodlight Footcandle Plot Based on 360glare-free coverageFloodlight Footcandle Plot BAL120R-Reflector-Shaped Balloon Floodlight Footcandle Plot BAL-115D-Drum Shaped Balloon Alarm Buzzer Machine Safety DecalsGeneral Information Balloon EnvelopesComponents Major ComponentsComponents Setup GloBug SetupPositioning the Balloon SETUP/OPERATION Applying PowerPlace the power ON/OFF switch in the OFF position ShutdownShutdown StorageMaintenance ZipReconnect the power cables Installing a New LampRemoving the Lamp Cable Removing the Lamp/Balloon AssemblyRemoval of Winch Cable Release Access Point Installation of Winch Cable Route the cable around the pulley of the first mast aBallast Box Removal Installation of WinchCutoff any excess zip tie material Balloon/Lamp Placement Maintenance Wiring Diagram Wiring DiagramM1 C6 Periodic Check and Maintenance Troubleshooting Lamps Troubleshooting Mast Explanation of Codes in the Remarks Column Xxxxx only Not Used onSuggested Spare Parts Qty DescriptionBulb Balloon ClothNameplate and Decals Lamp Cover BuzzerNameplate and Decals Decal Caution Cover InformationDecal Caution Lamp Cover Buzzer DECALWARNING, Lift HangerHandle Assy Handle AssyHandle Grip Includes Item W Snap RingSleeve Bearing 30DX34DX20 Base PlateSteering Assy Steering Assy Front Shaft LFront Shaft R Brake PedalOutrigger Assy Outrigger AssyWeight OUT,R R Weight OUT,R LBracket OUT,R R Spacer OUT,R Includes Item WMast Adapter Assy Mast Adapter AssyStand Shaft StandSpacer Stand WasherMain Mast Assy Main Mast AssySwitch Assy Screw & WASHER, M5X8Winch HM-G103 First MastWinch Assy Winch AssyFrame Drum ShaftWASHER, Lock M8 BOLT, M8X15Mast Section Assy Mast Section AssySecond Mast Third MastBaseplate Cover Assy Baseplate Cover AssyCover Ballast BOX Ballast CPStopper Free BushBallast Assy Ballast AssyWASHER, M4 BALLAST, CPBallast Holder HolderFAN BLOWER/LAMP Base Assy FAN BLOWER/LAMP Base AssyCOVER, Wire Micro SwitchMicro Switch CAP Sensor Micro Switch CoverBALLOON/LAMP Guard Assy BALLOON/LAMP Guard AssyLamp Lamp GuardBalloon Cloth CP SEAL, NormalTerms and Condition of Sale Parts Freight PolicyPage HERE’S HOW to GET Help

BG113BC specifications

The Multiquip BG113BC is a cutting-edge concrete and masonry saw designed to meet the demanding needs of construction professionals. This powerful tool combines efficiency, durability, and precision, making it a staple for any mason or contractor looking to deliver high-quality work.

At the core of the BG113BC is its robust engine, which delivers reliable power needed for tough cutting applications. The saw is equipped with a 13 horsepower Honda GX390 engine, which provides both high performance and fuel efficiency. This allows users to work longer hours without the need for constant refueling, helping to improve productivity on job sites.

One of the standout features of the BG113BC is its advanced water containment system. This system is designed to minimize dust production during cutting operations, which is beneficial for both operator safety and compliance with environmental regulations. The integrated water pump ensures that the blade remains cool, reducing wear and tear and extending its lifespan while providing cleaner cuts.

The BG113BC is designed for user comfort and ease of operation. It has a lightweight and compact design that makes it easy to maneuver, even in tight spaces. The adjustable handle provides ergonomic support, allowing operators to maintain a comfortable grip while cutting for extended periods. This reduces operator fatigue and enhances overall effectiveness.

Another impressive characteristic of this concrete saw is its cutting depth capability. With a maximum cutting depth of up to 4.5 inches, it is capable of tackling a variety of materials, including concrete, asphalt, and brick. The blade guard features an easy-to-adjust design that allows operators to quickly change the depth of the cut, increasing versatility on the job.

In terms of technology, the BG113BC incorporates a quick-release blade guard, which simplifies blade changes. This feature significantly reduces downtime and helps maintain workflow. Additionally, the saw is designed with a sturdy frame that reduces vibrations, leading to a more stable cutting experience.

Overall, the Multiquip BG113BC is an exceptional concrete and masonry saw that reflects the brand's unwavering commitment to quality and performance. With its powerful engine, user-friendly features, and innovative technologies, this saw is an invaluable asset for any construction project, ensuring that professionals can achieve precise cuts with ease and efficiency.
Top Page Image Contents