Multiquip BG113BC manual „ Never attempt service on a running machine

Page 7

SAFETY INFORMATION

LIGHTING SYSTEM SAFETY

DANGER

„ NEVER use lighting system in rain, snow or areas of high humidity that could generate electrical storms.

WARNING

„NEVER disconnect any emergency or safety devices. These devices are intended for operator safety. Disconnection of these devices can cause severe injury, bodily harm or even death. Disconnection of any of these devices will void all warranties.

CAUTION

„NEVER attempt service on a running machine.

NOTICE

„To prevent the lighting system from overturning, NEVER use in winds that exceed 22mph (10 m/s).

„The lighting system should only be used in temperatures between 23° to 104°F (-5° to 40° C). Failure to comply with these operating parameters could cause the lamp to malfunction and shorten the ballast life.

„ALWAYS keep the lighting system in proper running condition.

„Fix damage to lighting system and replace any broken parts immediately.

„ALWAYS store equipment properly when it is not being used. Equipment should be stored in a clean, dry location out of the reach of children and unauthorized personnel.

LAMP SAFETY

WARNING

„NEVER attempt to replace lamp with the power on. Always unplug the power cord from the generator or power source when changing the lamp.

„ALWAYS allow a sufficient amount of time for the lamp to cool before changing. The possibility exists of severe burns.

CAUTION

„NEVER use force when installing the lamp. Excessive force could cause the lamp to break, causing bodily harm.

NOTICE

„NEVER leave any grease or oil residue on lamp surface when replacing or removing lamp. This can create hot spots, reducing the service life of the lamp.

„ALWAYS make sure lamp surface is clean and dry.

„ALWAYS replace with MQ recommended type lamp. See parts section of this manual.

„If applicable, ALWAYS make sure the lamp guard is installed correctly. NEVER deform the lamp guard.

„NEVER unplug the lamp’s AC power cable during operation.

„ALWAYS have a trained technician to install and remove lamp or replace any damaged fixture wiring.

BALLOON SAFETY

WARNING

„To prevent serious burns, NEVER touch or unzip the balloon envelope when the

lamp is on.

CAUTION

„ALWAYS keep the balloon away from sharp objects and excessive amounts of heat.

NOTICE

„To prevent balloon deformation, NEVER use lighting system in strong winds.

„DO NOT place the balloon inside its protective cover until the lamp has had a sufficient amount of time to cool down. This will prevent the balloon’s nylon cover from being burned (touching the lamp surface).

„ALWAYS place the balloon inside its protective cover after each use. This will prolong the life of the balloon material, keeping it protected from harsh environmental elements.

„Replace balloon immediately if damaged. A damaged balloon will not inflate properly, and may become more damaged by touching the hot lamp surface.

„DO NOT use excessive force when zipping and unzipping the balloon. Be gentle with the zipper mechanism. If the zipper is broken, the balloon will become unusable.

GB113BC GLOBUG LIGHTING SYSTEM — OPERATION AND PARTS MANUAL — REV. #5 (01/16/12) — PAGE 7

Image 7
Contents Model GB113BC Proposition 65 Warning Page Table of Contents Ordering parts has never been easier Parts Ordering Proceduresfire extinguisher Safety InformationResult in injury to yourself and others „ Always know the location of the nearest„ Never unplug the lamp’s AC power cable during operation „ Never attempt service on a running machine„ Always make sure the area above Generator SafetyLoading and Unloading Specifications SpecificationsTOP View Side View Stow Position Rear View DimensionsBased on 360glare-free coverage Floodlight Footcandle PlotFloodlight Footcandle Plot BAL120R-Reflector-Shaped Balloon Floodlight Footcandle Plot BAL-115D-Drum Shaped Balloon Balloon Envelopes Alarm BuzzerMachine Safety Decals General InformationMajor Components ComponentsComponents GloBug Setup SetupPositioning the Balloon Shutdown SETUP/OPERATIONApplying Power Place the power ON/OFF switch in the OFF positionStorage ShutdownZip MaintenanceInstalling a New Lamp Reconnect the power cablesRemoval of Winch Removing the Lamp/Balloon AssemblyRemoving the Lamp Cable Cable Release Access Point Route the cable around the pulley of the first mast a Installation of Winch CableCutoff any excess zip tie material Installation of WinchBallast Box Removal Balloon/Lamp Placement Wiring Diagram Maintenance Wiring DiagramM1 C6 Periodic Check and Maintenance Troubleshooting Lamps Troubleshooting Mast Xxxxx only Not Used on Explanation of Codes in the Remarks ColumnBalloon Cloth Suggested Spare PartsQty Description BulbLamp Cover Buzzer Nameplate and DecalsDECALWARNING, Lift Hanger Nameplate and DecalsDecal Caution Cover Information Decal Caution Lamp Cover BuzzerHandle Assy Handle AssyBase Plate Handle Grip Includes Item WSnap Ring Sleeve Bearing 30DX34DX20Steering Assy Brake Pedal Steering AssyFront Shaft L Front Shaft ROutrigger Assy Outrigger AssySpacer OUT,R Includes Item W Weight OUT,R RWeight OUT,R L Bracket OUT,R RMast Adapter Assy Mast Adapter AssyWasher StandShaft Stand Spacer StandMain Mast Assy Main Mast AssyFirst Mast Switch AssyScrew & WASHER, M5X8 Winch HM-G103Winch Assy Winch AssyBOLT, M8X15 FrameDrum Shaft WASHER, Lock M8Mast Section Assy Mast Section AssyThird Mast Second MastBaseplate Cover Assy Baseplate Cover AssyFree Bush Cover BallastBOX Ballast CP StopperBallast Assy Ballast AssyHolder WASHER, M4BALLAST, CP Ballast HolderFAN BLOWER/LAMP Base Assy FAN BLOWER/LAMP Base AssyMicro Switch Cover COVER, WireMicro Switch Micro Switch CAP SensorBALLOON/LAMP Guard Assy BALLOON/LAMP Guard AssySEAL, Normal LampLamp Guard Balloon Cloth CPFreight Policy Terms and Condition of Sale PartsPage HERE’S HOW to GET Help

BG113BC specifications

The Multiquip BG113BC is a cutting-edge concrete and masonry saw designed to meet the demanding needs of construction professionals. This powerful tool combines efficiency, durability, and precision, making it a staple for any mason or contractor looking to deliver high-quality work.

At the core of the BG113BC is its robust engine, which delivers reliable power needed for tough cutting applications. The saw is equipped with a 13 horsepower Honda GX390 engine, which provides both high performance and fuel efficiency. This allows users to work longer hours without the need for constant refueling, helping to improve productivity on job sites.

One of the standout features of the BG113BC is its advanced water containment system. This system is designed to minimize dust production during cutting operations, which is beneficial for both operator safety and compliance with environmental regulations. The integrated water pump ensures that the blade remains cool, reducing wear and tear and extending its lifespan while providing cleaner cuts.

The BG113BC is designed for user comfort and ease of operation. It has a lightweight and compact design that makes it easy to maneuver, even in tight spaces. The adjustable handle provides ergonomic support, allowing operators to maintain a comfortable grip while cutting for extended periods. This reduces operator fatigue and enhances overall effectiveness.

Another impressive characteristic of this concrete saw is its cutting depth capability. With a maximum cutting depth of up to 4.5 inches, it is capable of tackling a variety of materials, including concrete, asphalt, and brick. The blade guard features an easy-to-adjust design that allows operators to quickly change the depth of the cut, increasing versatility on the job.

In terms of technology, the BG113BC incorporates a quick-release blade guard, which simplifies blade changes. This feature significantly reduces downtime and helps maintain workflow. Additionally, the saw is designed with a sturdy frame that reduces vibrations, leading to a more stable cutting experience.

Overall, the Multiquip BG113BC is an exceptional concrete and masonry saw that reflects the brand's unwavering commitment to quality and performance. With its powerful engine, user-friendly features, and innovative technologies, this saw is an invaluable asset for any construction project, ensuring that professionals can achieve precise cuts with ease and efficiency.