Outdoor Installation, Indoor Installation

Installation

Outdoor Installation

Install the generator in a area that is free of debris, bystanders, and overhead obstructions. Make sure the generator is on secure level ground so that it cannot slide or shift around. Also install the generator in a manner so that the exhaust will not be discharged in the direction of nearby homes.

The installation site must be relatively free from moisture and dust. All electrical equipment should be protected from excessive moisture. Failure to do will result in deterioration of the insulation and will result in short circuits and grounding.

Foreign materials such as dust, sand, lint and abrasive materials have a tendency to cause excessive wear to engine and alternator parts.

CAUTION

Pay close attention to ventilation when operating the generator inside tunnels and caves.The engine exhaust contains noxious elements. Engine exhaust must be routed to a ventilated area.

Indoor Installation

Exhaust gases from diesel engines are extremely poisonous. Whenever an engine is installed indoors the exhaust fumes must be vented to the outside. The engine should be installed at least two feet from any outside wall. Using an exhaust pipe which is too long or too small can cause excessive back pressure which will cause the engine to heat excessively and possibly burn the valves.

Mounting

The generator must be mounted on a solid foundation (such as concrete) and set firmly on the foundation to isolate vibration of the generator when it is running.The generator must set at least 6 inches above the floor or grade level (in accordance to NFPA 110, Chapter 5-4.1). DO NOT remove the metal skids on the bottom of the generator. They are to resist damage to the bottom of the generator and to maintain alignment.

Generator Grounding

To guard against electrical shock and possible damage to the equipment, it is important to provide a good EARTH ground (Figure 2).

Article 250 (Grounding) of the National Electrical Code (NEC) provides guide lines for proper grounding and specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical.

NEC articles 250-64(b) and 250-66 set the following grounding requirements:

1.Use one of the following wire types to connect the generator to earth ground.

a.Copper - 8 AWG (5.3 mm2) or larger.

b.Aluminum - 6 AWG (8.4 mm2) or larger.

2.When grounding the generator (Figure 2) connect the ground cable between the lock washer and the nut on the generator and tighten the nut fully. Connect the other end of the ground cable to earth ground.

3.NEC article 250-52(c) specifies that the earth ground rod should be buried a minimum of 8 ft. into the ground.

NOTICE

When connecting the generator to any buildings electrical system ALWAYS consult with a licensed electrician.

DCA20spxu2 servpro® • operation and parts manual — rev. #0 (09/23/13) — page 15

DCA20spxu2 specifications

The Multiquip DCA20SPXU2 is a powerful and versatile portable generator that has become a favorite among contractors and outdoor enthusiasts alike. Designed for reliability and efficiency, this unit boasts a range of features that make it suitable for various applications, from construction sites to recreational activities.

One of the standout characteristics of the DCA20SPXU2 is its robust engine. Powered by a reliable 20 kW diesel engine, this generator offers ample power to run essential tools and equipment, ensuring that users can depend on it for demanding tasks. The engine is not only powerful but also designed for fuel efficiency, helping users save on operating costs during extended use.

The DCA20SPXU2 features an impressive run time, with a large fuel tank that enables it to operate for long periods without requiring frequent refueling. This is particularly beneficial for projects that are located in remote areas or for outdoor events where electricity is critical.

Another key highlight of the DCA20SPXU2 is its advanced sound attenuation design. This generator operates quietly, adhering to stringent noise regulations, which is essential when working in residential or noise-sensitive environments. The sound-dampening technology helps to minimize sound levels, making it an excellent choice for events and job sites that demand a quieter operation.

Multiquip has also integrated a user-friendly control panel in the DCA20SPXU2, featuring intuitive gauges and indicators that provide vital information at a glance, such as fuel levels, output voltage, and operational status. This ease of use allows operators to quickly monitor performance and make necessary adjustments.

The generator is equipped with multiple outlets, including 120V and 240V options, ensuring that it can power a variety of tools and equipment simultaneously. This versatility enhances its appeal for users who require flexibility in their power source.

Durability is another hallmark of the DCA20SPXU2. Built with high-quality materials, the generator is designed to withstand tough conditions, making it an ideal companion for construction sites or outdoor adventures.

In conclusion, the Multiquip DCA20SPXU2 is a well-engineered portable generator that offers a blend of power, efficiency, and convenience. With its robust engine, quiet operation, user-friendly controls, and durable construction, it stands out as a reliable choice for both professional and recreational use, meeting the power needs of a variety of users.