MP2 Masonry SAW PRE-SETUP Gasoline Engine

MP2 MASONRY SAW — PRE-SETUP (GASOLINE ENGINE)

Pre-Setup

CAUTION - Shut-down Saw for Cleaning

Whenever cleaning, adjusting or lubricating any part of the saw, MAKE CERTAIN to stop the engine and disconnect the spark plug wire from the spark plug.

The MP2 Masonry Saw gasoline model utilizes some of the same procedures that are used for the electric models. Please reference pages 20 and 21 for the below referenced procedures:

■Conveyor Cart Placement

■Blade Selection and Inspection

■Saw Blades

■Blade Installation

Assembly (Gasoline Powered Saws Only)

1.Remove the saw from its container and place it on a stable, level surface. Make sure location you choose can support the weight of the saw. The saw location should be rigid and stationary so that the saw will not move, sag, or sway due to the vibrations and movements of the saw.

2.The gasoline powered saw uses a mechanical water pump. This pump operates by drawing power from the drive V-belts, and has been adjusted dry cutting operation when shipped from the factory.

3.Fill the water tray with clean fresh water. The water pump intake (strainer) must always be fully covered by water to operate effectively. Also, keep the pump intake free of sludge, debris and other materials that may accumulate in the tray.

4.Make certain that the water hose will not come in contact with the blade or interfere with any moving parts. The best location for the water pump/strainer is between the splash shield and the rear of the water tray. This will prevent some of the abrasive particles from flowing through the pump.

CAUTION -Water Strainer Placement

ALWAYS position the strainer in the water tray in a manner that will allow the free movement of the conveyor cart, and clearance from the cutting blade and cutting action.

The mechanical water pump is

NOTEshipped from the factory for dry cutting applications.

Wet Cutting Setup (Gasoline Only)

To connect the mechanical water pump to the drive V- belts for Wet Cutting, perform the following:

1.Loosen the 2 hex head cap screws (Figure 12) that secure the pump mount bracket.

2.Push the pump handle downward to engage the pump. The drive belt should have approximately 1/8 to 3/16 inch belt deflection.

3.Tighten the 2 hex head cap screws that secure the pump mount bracket.

Figure 12. Pump Engage

4.With the engine running, squeeze the water pump priming bulb (Figure 13) until water begins to flow through the water lines. If the pump is working correctly, the cutting blade should be covered with a steady water mist. This will keep the blade cool while cutting.

Figure 13. Priming Bulb

MQ MP2 MASONRY SAW — OPERATION MANUAL — REV. #2 (3/12/13) — PAGE 23

MP2090HP, MP2050E3, MP2050E1 specifications

The Multiquip MP2050E1, MP2050E3, and MP2090HP are powerful and versatile electric-powered concrete and masonry saws designed for a variety of cutting applications. Built with durability and performance in mind, these models cater to the needs of professional contractors, offering exceptional efficiency and precision in both residential and commercial projects.

The MP2050E1 features a high-torque electric motor that ensures reliable operation and consistent cutting performance. It comes equipped with a 20-inch blade capacity, allowing users to tackle medium to large-sized jobs with ease. The saw is designed with an ergonomic handle and adjustable height for optimal user comfort during extended use. Additionally, the MP2050E1 boasts a compact design, making it easy to transport and maneuver around job sites.

On the other hand, the MP2050E3 is an upgraded version that incorporates advanced features while maintaining the same blade capacity as its predecessor. This model includes a three-phase motor, which enhances power efficiency and increases the saw's longevity. The MP2050E3 is engineered with a robust chassis for increased stability during operation, and it also offers improved dust management capabilities to keep the work area clean and safe.

The Multiquip MP2090HP stands out with its higher horsepower motor, optimizing productivity for heavy-duty cutting tasks. This model supports a larger blade size of up to 30 inches, making it ideal for cutting thicker materials. The MP2090HP is equipped with a sophisticated water control system that ensures consistent cooling of the blade, preventing overheating and prolonging blade life. Its heavy-duty construction is designed to withstand the rigors of demanding job sites, offering maximum reliability.

All three models utilize cutting-edge technology, including adjustable cutting depth settings, which allow operators to customize their cutting depth for precision and versatility. They also feature high-performance bearings that provide smooth blade rotation, enhancing overall cutting efficiency.

In summary, the Multiquip MP2050E1, MP2050E3, and MP2090HP are exemplary tools for professionals in the concrete and masonry industry. Each model boasts unique features tailored to meet varying job requirements, while their advanced technologies ensure high performance, safety, and ease of use. Whether tackling small renovations or large construction projects, these saws provide the reliability and power needed to achieve exceptional results.