Multiquip ga-6h GA-6H/GA-6HA Installation, Outdoor Installation, Mounting, Indoor Installation

Page 21

Outdoor Installation

Install the generator/welder in a area that is free of debris, bystanders, and overhead obstructions. Make sure the generators is on secure level ground so that it cannot slide or shift around. Also install the generators in a manner so that the exhaust will not be discharged in the direction of nearby homes.

The installation site must be relatively free from moisture and dust. All electrical equipment should be protected from excessive moisture. Failure to do will result in deterioration of the insulation and will result in short circuits and grounding.

Foreign materials such as dust, sand, lint and abrasive materials have a tendency to cause excessive wear to engine and alternator parts.

CAUTION

Pay close attention to ventilation when operating the generators inside tunnels and caves.The engine exhaust contains noxious elements.

Mounting

The generators should always be mounted on a flat level surface to isolate vibration of the generators when it is running. DO NOT place the generators on slopes, the possibility exists that the generators could slide.

CAUTION

An electric shock is apt to happen when vibrators are used. Pay close attention to handling when operating vibrators and always use rubber boots and gloves to insulate the body from a short circuit.

GA-6H/GA-6HA — INSTALLATION

Indoor Installation

Exhaust gases from gasoline engines are extremely poisonous. Whenever an engine is installed indoors the exhaust fumes must be vented to the outside. The engine should be installed at least two feet from any outside wall. Using an exhaust pipe which is too long or too small can cause excessive back pressure which will cause the engine to heat excessively and possibly burn the valves.

Eliminate the danger of deadly carbon monoxide gas. Remember that exhaust fumes from any gasoline engine are very poisonous if discharged in a closed room, but harmless if allowed to mix with the outside air. If the generators is installed indoors, you must make provisions for venting the engine exhaust to the outside of the building.

Generators Grounding

To guard against electrical shock and possible damage to the equipment, it is important to provide a good EARTH ground. Always use the ground terminal on the generators to ground the generator. Ground the generators from its ground connector so that the resistance to ground is 500 ohms or less.

Article 250 (Grounding) of the National Electrical Code (NEC) provides guide lines for proper grounding and specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical.

NEC articles 250-64(b) and 250-66 set the following grounding requirements:

1.Use one of the following wire types to connect the generators to earth ground.

a.Copper - 10 AWG (5.3 mm2) or larger.

b.Aluminum - 8 AWG (8.4 mm2) or larger.

2.When grounding the generators (Figure 3) connect the ground cable between the lock washer and the nut on the generators and tighten the nut fully. Connect the other end of the ground cable to earth ground.

3.NEC article 250-52(c) specifies that the earth ground rod should be buried a minimum of 8 ft. into the ground.

GA-6H/GA-6HA A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (06/02/05) — PAGE 21

Image 21
Contents Model GA-6H/GA-6HA Page Heres HOW to GET Help Table of Contents When ordering parts Please supply the following information Parts Ordering ProceduresGA-6H/GA-6HA Safety Message Alert Symbols Burn HazardsRespiratory Hazards Rotating Parts Hazards Equipment DamageRead this manual GA-6H/GA-6HA Rules for Safe OperationPower Cord Safety Emergencies DeathOperation and Safety Decals Machine Safety DecalsEffects of Altitude and Heat GA-6H/GA-6HA Specifications GeneratorsGA-6H/GA-6HA Specifications Engine Specifications EngineDimensions GA-6H/GA-6HA DimensionsGA-6H/GA-6HA General Information Incandescent Loads Single Phase Load 60 HzSmall Motors Large MotorsGenerators Components GA-6H/GA-6HA Controls and IndicatorsWhen the full power switch is FuelTank Fuel tank capacity is 5 gallons 19 liters GA-6H/GA-6HA Controls and IndicatorsGenerators Refueling GA-6H/GA-6HA Generator RefuelingOutdoor Installation GA-6H/GA-6HA InstallationIndoor Installation MountingConnecting the Ground GA-6H/GA-6HA InstallationGA-6H/GA-6HA PRE-INSPECTION General Inspection Prior to Operation Ground Power ToolsExtension Cable Main Circuit BreakerBefore Starting GA-6H/GA-6HA PRE-INSPECTION EngineEngine Oil Check Fuel CheckBefore Starting the Engine GA-6H/GA-6HA Initial START-UP EngineGA-6H/GA-6HA Initial START-UP/GENERATOR Operation Stopping the Engine Connecting the LoadGenerators Storage GA-6H/GA-6HA Preparation for Longterm StoragePage Engine Maintenance Schedule GA-6H/GA-6HA Maintenance EngineMaintenance GA-6H/GA-6HA Maintenance EngineGA-6H Wiring Diagram GA-6H -WIRING Diagram GeneratorGA-6HA Wiring Diagram GA-6HA -WIRING Diagram GeneratorEngine Troubleshooting GA-6H/GA-6HA -TROUBLESHOOTING EngineWhite Generator Troubleshooting GA-6H/GA-6HA -TROUBLESHOOTING GeneratorPage GA-6H/GA-6HA Explanation of Code in Remarks Column How to read the marks and remarks used in this partsItems Found In the Remarks Column Items Found In the Items Number ColumnDescription GA-6H/GA-6HA Suggested Spare PartsName Plate Assy GA-6H/GA-6HA Nameplate and DecalsDecal MQ Multiquip Decal Operating InstructionsDecalwarning Generator Assy GA-6H/GA-6HA Generator AssyBEARING, 6304 2RU Nycm RECTIFIER, D3SB80SET BOLT, Rotor SET WASHER, BearingControl BOX ASSY. GA-6H GA-6H Control BOX AssyIdle Control SWITCH, C1550WA Full Power SWITCH, ET-330D12Operation SWITCH, C1550WA Control BOXControl BOX Assy GA-6HA Control BOX AssyGA-6HA Control BOX Assy Muffler Assy GA-6H/GA-6HA Muffler AssyBolt HEX Head MufflerBracket HEX NUTPipe Frame Assy GA-6H/GA-6HA Pipe Frame AssyBase GA-6HARubber Suspension Fuel TankAIR Cleaner Assy Honda GX340K1EDE2 Engine AIR Cleaner AssySEPARATOR, AIR Cleaner ELEMENT, AIR CleanerHOUSING, AIR Cleaner STAY, AIR CleanerCamshaft Assy Honda GX340K1EDE2 Engine Camshaft AssyROD, Push SPRING, Weight ReturnARM, Valve Rocker LIFTER, ValveCarburetor Assy Honda GX340K1EDE2 Engine Carburetor AssyCLIP, Wire Harness GASKET, AIR CleanerGasket SET Valve SET, FloatControl Assy Honda GX340K1EDE2 Engine Control AssyARM, Governor SPRING, Control AdjustingROD, Governor SPRING, GovernorCrankcase Cover Assy Honda GX340K1EDE2 Engine Crankcase Cover AssyHOLDER, Governor Weight WEIGHT, GovernorPIN, Governor Weight GASKET, Case CoverCrankshaft Assy Honda GX340K1EDE2 Engine Crankshaft AssyCrankshaft E-TYPE WEIGHT, BalancerCylinder Barrel Assy Honda GX340K1EDE2 Engine Cylinder Barrel AssyWIRE, Ground Switch ASSY., OIL LevelSHAFT, Governor ARM BOLT, Drain PlugCylinder Head Assy Honda GX340K1EDE2 Engine Cylinder Head AssyGUIDE, EX. Valve OS Optional GUIDE, Valve OS OptionalCLIP, Valve Guide GASKET, Cylinder HeadFAN Cover Assy Honda GX340K1EDE2 Engine FAN Cover AssyCOVER, FAN *NH1* Black ShroudGROMMET, Drain Hole Flywheel Assy Honda GX340K1EDE2 Engine Flywheel AssyFAN, Cooling FLYWHEEL, LampNUT, Special 16MM Ignition Coil Assy Honda GX340K1EDE2 Engine Ignition Coil AssyGROMMET, Wire CLAMP, WireWIRE, Stop Switch 470MM HOLDER, Stop Switch WirePiston Assy Honda GX340K1EDE2 Engine Piston AssyRing SET, Piston STD BOLT, Connecting RODPiston STD PIN, PistonHonda GX340K1EDE2 Engine Recoil Starter Assy RATCHET, Starter PULLEY, Recoil StarterSPRING, Friction SPRING, Starter ReturnSolenoid Assy Honda GX340K1EDE2 Engine Solenoid AssyLEVER, Throttle SPRING, Choke ReturnLabels Assy Honda GX340K1EDE2 Engine Labels AssyEmblem MARK, AIR CleanerMARK, Choke MARK, OIL CautionEffective October 1, 2002 Terms and Conditions of Sale Parts Page Your Local Dealer is
Related manuals
Manual 2 pages 55.13 Kb

ga-6h, GA-6HA specifications

The Multiquip GA-6HA is a versatile and robust generator designed to meet the power needs of a variety of applications, particularly in construction, events, and emergency backup situations. With its compact design and impressive performance capabilities, the GA-6HA is an ideal choice for professionals and contractors who require reliable electrical supply in remote locations or during power outages.

One of the standout features of the GA-6HA is its powerful 6,000-watt output, which provides sufficient power to run multiple tools and equipment simultaneously. This generator is equipped with a Honda GX390 engine, known for its durability and fuel efficiency. The engine operates quietly, making it suitable for use in noise-sensitive environments. Furthermore, the advanced design of the engine ensures minimal emissions, aligning with environmental regulations and promoting cleaner operation.

In terms of technology, the GA-6HA is fitted with a heavy-duty alternator that delivers stable power with a rated output of 120/240 volts. This feature allows users to connect various electrical devices without worry of voltage fluctuations that could damage sensitive equipment. The generator also incorporates a manual reset circuit breaker for added safety, preventing overload conditions.

Durability is a significant characteristic of the GA-6HA, as it is built with a rugged steel frame that can withstand the rigors of outdoor use. The generator's design includes an integrated lift hook for easy transport and positioning on job sites. Additionally, the anti-vibration mounts help to minimize noise and maintain stability during operation.

The GA-6HA features multiple outlets, including 120V 20A duplex receptacles and a 120/240V 30A locking receptacle, providing flexibility for connecting various tools and appliances. An easy-to-read fuel gauge and easy-access control panel contribute to user-friendliness and operational efficiency.

Overall, the Multiquip GA-6HA is designed to be a reliable power solution, effectively combining performance, durability, and portability. Whether for construction sites, outdoor recreational activities, or emergency power needs, this generator stands out for its impressive features and user-centric design.