Lexicon Lexicon Part #070-13234 Restore Factory Defaults, Equalization, Bass and Treble Level

Page 19

DC-1 Version 4 Digital Controller

System 2

Configuration System

Configuration

Restore

Factory Defaults

Although the DC-1 memory is cleared before it leaves the factory, it is good practice to restore the factory defaults with the following procedure before system configuration.

Turn the DC-1 OFF with the remote control. Turn the unit back ON and immediately press and hold the MUTE button on the remote. (Make sure you do not block the infrared receiver on the DC-1 front panel.) The display will read:

Press ▼ to highlight RESTORE DEFAULTS, then press SELECT. This will clear and reload all preset effects and all factory settings of Volume, Balance, Contrast, Configuration, etc. When the message FACTORY DE- FAULTS RESTORED is displayed, press DONE to return to normal opera- tion.

In the main menu, press SELECT to open the Equalization menu which contains Bass, Treble and Tilt controls, and a Loudness parameter.

Bass and Treble level controls are provided to compensate for inconsisten- cies in source material, rather than variations in room conditions. The BASS LEVEL control allows a boost or cut of as much as 6dB below 250Hz. The TREBLE LEVEL control allows a boost or cut of 6dB above 1.5kHz. To select either control for adjustment, use ▲ or▼ to select the control, press SELECT, and use ▲ or ▼ to adjust the setting.

These controls do not affect the sound of rear or side speakers.

Equalization

Bass and Treble Level

11

Image 19

Contents DC-1 Digital Controller Software Communications Notice Important Safety InstructionsAcknowledgements Vigtig information om sikkerhed Wichtige Sicherheitsanweisungen Contents AC-3 Effects and Parameters TroubleshootingSpecifications Installation Worksheet PCM Effects and ParametersIntroduction Glossary of Terms Using the DocumentationPage Front Panel Controls and IndicatorsRear Panel InstallationON, FP and OSD Remote ControlFunctions Using the Shift Alternate Remote ControlRecord/Zone 2 buttons Installation Location Considerations AC Connections ConnectionAudio/Video Cables Wiring ConsiderationsWire Lengths AWG Size Audio/Video ConnectionsInstallation LD/DVD Players Video ConnectionsDigital Audio Connections AC-3 Ready Laser DiscEqualization Restore Factory DefaultsBass and Treble Level Tilt System ConfigurationVideo On-Screen Display Display AdjustmentVideo Input Selection On-Screen Display Input Gain Input ConfigurationAnalog Inputs Only Input Name Restore Input NameInput Effect FX Assignment Input PCM Effect AC-3 Effect DTS Effect AutomaticSystem Configuration DTS Only PCM Only AC-3 OnlyCoax 1-2 VideoDigital Audio Inputs Record/Zone 2 Controls Record/ZoneOFF Custom Configuration Speaker ConfigurationFront L/R Sides Rears CenterTHX Configuration Surround EX Configuration Setting Output LevelsSubwoofer Output System Configuration System Configuration Speaker Distance Mute Level Power On Volume Zone 2 Power On VolumeSync Delay Calibrate Panorama System Configuration Customization Locking Settings Assign Custom NameBalance Zone 2 Balance System Configuration Naming your custom Effect Restoring the original parameter values An EffectNightclub PanoramaChurch PCM Effects and ParametersMusic Surround ChannelLogic Pro Logic TV MatrixPCM Effect Parameters PCM Effects and Parameters PCM Effects and Parameters PCM Effects and Parameters PCM Effects and Parameters AC-3 Effects and 4 AC-3 EffectsParametersnd Parameters Music AC-3 Effects and ParametersDolby Digital To on for proper decoding of Surround EX soundtracks THXAC-3 Effects and Parameters AC-3 Effects and Parameters DTS Music DTS 2-ChannelDTS Film DTS LogicDTS Effect Parameters DTS Effects and Parameters Problem TroubleshootingPossible Cause and Solution Problem Possible Cause and Solution TroubleshootingRoutine Maintenance Restoring Defaults TroubleshootingSpecifications Inputs Speaker Configuration circle selection