Land Pride RCR1884 manual Leveling Procedure, Deck Leveling From Left to Right, Refer to -5 on

Page 20

Table of Contents

Section 2: Adjustments

Land Pride

Leveling Procedure

There are 4 primary adjustments that should be made prior to actual field operations:

•Deck leveling from left to right

•Tractor top link length

•Tractor lower link height

•Tailwheel height

Proper adjustment of each of these items will provide for higher efficiency, improved cutting performance and longer blade life. The following tools will be needed:

•Pliable tape measure

•Carpenters level

•3/4” Open end or hex end wrench or socket set

•Protective gloves

Deck Leveling From Left to Right

Refer to Figure 2-1:

1.Locate tractor and Rotary Cutter on a flat, level surface.

2.Use tractor’s hydraulic 3-point control to lower cutter until tailwheel contacts ground surface.

!DANGER

Engage parking brake, disengage PTO, shut off tractor and remove key before proceeding. Ensure that all moving parts have come to a complete stop before dismounting from tractor.

3.Place a Carpenters level or other suitable leveling device on the front of the cutter deck. Adjust either one or both of the tractors 3-point lower link height adjustments to level the deck from left to right. Some tractors have only a single adjusting crank.

13831

Deck Leveling

Figure 2-1

Deck Leveling From Front to Rear

!CAUTION

Wear a pair of gloves when checking cutting height. Avoid direct contact with the cutting edge of the blade.

!DANGER

Engage parking brake, disengage PTO, shut off tractor and remove key before proceeding. Ensure that all moving parts have come to a complete stop before dismounting from tractor.

IMPORTANT: Blade positioning is very important. The blades should be positioned to cut material only at the front of the cutter as shown in Figure 2-5 on page 19. If deck is level or rear of cutter is lower than the front, then the blades are subject to continuous material flow resulting in additional blade wear, horsepower loss and frequent blade sharpening.

Refer to Figure 2-1:

1.Place a Carpenters level on one of the main deck channels. Using the tractor’s 3-point hydraulic control lever, raise or lower the 3-point arms until the deck is slightly lower at the front (approximately 1” lower) than at the back.

2.The top center link should be loose when deck rear is supported by the tail wheel. If not, lengthen center link until loose. Final adjustment will be made later.

Refer to Figure 2-5 on page 19:

3.With gloves on, carefully rotate each blade to the position shown in Figure 2-5 on page 19.

4.At the front of the cutter, measure the distance from blade cutting tip to ground surface. This distance is known as the “Nominal Cutting Height”.

5.The tail wheel will need adjusting if nominal cutting height is not at the preferred cutting height. Adjust tailwheel per instructions on page 19.

6.Repeat steps 1 to 5 until preferred cutting height is achieved.

7.Set stop on tractor lift quadrant so cutter can be returned to the same height.

Top Center Link Length Adjustment

Refer to Figure 2-2:

1.Lower cutter deck to the nominal cutting height.

2.Adjust length of tractor’s 3-point top center link such that the top and bottom hitch pins are aligned vertically with each other.

3.Lock center link in this position.

Vertical

Alignment of

Hitch Pins

24661

Top Link Adjustment

Figure 2-2

18 RCR1884 Series Rotary Cutters 312-880M

9/24/08

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Rotary Cutters Table of Contents Shutdown and Storage Be Aware Signal WordsFor Your Protection Use Safety Lights and Devices Use a Safety ChainPractice Safe Maintenance Transport Machinery SafelyPrepare for Emergencies Wear Protective EquipmentAvoid High Pressure Fluids Hazard Keep Riders Off MachinerySafety Labels 818-543C818-552C 818-540C818-556C 818-564C 818-230C818-130C Owner Assistance Using This ManualApplication Vent Plug Installation Tractor RequirementsCategory l Adapter Bushings Land Pride Cat. l Adapter BushingsPoint Hitch Assembly Single Tailwheel Assembly Tighten all locknuts to correct torqueDual Tailwheel Assembly Front Chain Guard Installation Optional Front Guard AssemblyFront Rubber Guard Installation Rear Metal Deflector Assembly Rear Chain Guard Installation OptionalPoint Tractor Hook-Up Driveline Installation Driveline Minimum LengthRefer to -10 on Refer to -12 onDriveline Shortening Leveling Procedure Top Center Link Length AdjustmentDeck Leveling From Left to Right Deck Leveling From Front to RearSingle Tail Wheel Height Adjustment Dual Tail Wheel Height AdjustmentOperating Checklist Operating Check ListTransporting Un-hooking the Rotary CutterCutting Instructions General Operating Instructions22 RCR1884 Series Rotary Cutters 312-880M Front and Rear Safety Guard Options AccessoriesRefer to -2 on MaintenanceCutter Blade Maintenance Driveline Protection Land Pride Cutter Blade PartsClutch Run-In Refer to Refer to FigureClutch Disassembly Clutch AssemblyCutter Storage Clutch InspectionLubrication HoursGauge Wheel Spindle Tube Gauge Wheel HubDriveline Profiles Driveline U-JointsDriveline Shield Bearings RCR1884 Model RCR1884Features & Benefits Features BenefitsProblem Cause Solution Oil seal leaking Driveline yoke or cross failingDriveline Clutch slippingProblem Cause Solution Excessive vibration In-tpi Ft-lb Mm x pitch Torque Values Chart for Common Bolt SizesAdditional Torque Values 34 RCR1884 Series Rotary Cutters 312-880M Warranty Overall Unit and Driveline One year Parts and LaborCorporate Office P.O. Box Salina, Kansas 67402-5060 USA
Related manuals
Manual 32 pages 25.68 Kb

RCR1884 specifications

The Land Pride Rotary Cutter RCR1884 is an exceptional piece of equipment designed to meet the needs of landowners, farmers, and contractors looking for reliability and performance in their land management tasks. This rotary cutter is engineered for cutting grass, weeds, and brush, making it an ideal choice for maintaining fields, pastures, and right-of-ways.

One of the standout features of the RCR1884 is its cutting width of 84 inches, allowing users to cover a large area efficiently. The heavy-duty construction ensures durability and longevity, with a robust design that can withstand tough operating conditions. The RCR1884 is built with a thick steel frame, ensuring stability and strength while in operation.

Equipped with a powerful gearbox, the RCR1884 delivers consistent power and performance. The gearbox is designed for low maintenance, which reduces downtime and increases productivity. This rotary cutter also features a dual blade system, which provides a smooth and clean cut while minimizing the risk of plugging, making it suitable for different types of terrain.

Safety is a priority in the design of the RCR1884. It is equipped with safety shields and guards that protect the operator from debris and potential hazards during operation. The cutter's slip clutch further enhances safety by protecting the driveline and limiting damage in the event of an unexpected obstruction.

The RCR1884 is designed for easy attachment to tractors, featuring a standard Category 1 hitch that offers versatility and compatibility with a variety of equipment. This makes it a practical choice for users who need to switch tools frequently.

Another notable aspect of the RCR1884 is its ability to handle various cutting conditions. It performs effectively in both light and heavy vegetation, making it suitable for everything from routine lawn care to more intensive brush clearing tasks. The adjustable cutting height allows operators to set the blades at the desired height, ensuring versatility based on specific needs.

In summary, the Land Pride Rotary Cutter RCR1884 is a robust and efficient tool for anyone involved in land management. With its generous cutting width, durable construction, powerful gearbox, and safety features, it is well-equipped to tackle a wide range of cutting tasks. Whether you are maintaining a small property or operating on larger agricultural land, the RCR1884 is designed to deliver reliable performance and exceptional results.
Top Page Image Contents