Land Pride RCR1884 manual Be Aware Signal Words, For Your Protection, Shutdown and Storage

Page 3

Land Pride

Important Safety Information

Table of Contents

These are common practices that may or may not be applicable to the products described in this manual.

Safety at All Times

Thoroughly read and understand the instructions given in this manual before operation. Refer to the “Safety Label” section, read all instructions noted on them.

Do not allow anyone to operate this equipment who has not fully read and comprehended this manual and who has not been properly trained in the safe operation of the equipment.

Look For The Safety Alert Symbol

The SAFETY ALERT SYMBOL indicates there is a

!safety precaution must be taken. When you see this symbol, be alert and carefully read the message that follows it. In addition to design and configuration of equipment, hazard control and accident prevention are dependent upon the awareness, concern, prudence and proper training of personnel involved in

the operation, transport, maintenance and storage of equipment.potential hazard to personal safety involved and extra

▲ Operator should be familiar with

all functions of the unit.

▲ Operate implement from the

driver’s seat only.

▲ Make sure all guards and shields

are in place and secured before

operating implement.

▲ Do not leave tractor or implement

unattended with engine running.

▲ Dismounting from a moving

tractor could cause serious injury

or death.

▲ Do not allow anyone to stand

between the tractor and

implement while backing up to the

implement.

▲ Keep hands, feet, and clothing

away from power-driven parts.

▲ Wear snug fitting clothing to avoid

entanglement with moving parts.

▲ Watch out for wires, trees, etc.,

Be Aware of

Signal Words

A Signal word designates a degree or level of hazard seriousness. The signal words are:

!DANGER

Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. This signal word is limited to the most extreme situations, typically for machine components that, for functional purposes, cannot be guarded.

!WARNING

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury, and includes hazards that are exposed when guards are removed. It may also be used to alert against unsafe practices.

!CAUTION

Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices.

when raising implement. Make

sure all persons are clear of

working area.

▲ Turning tractor too tight may

cause implement to ride up on

wheels. This could result in injury

or equipment damage.

▲ Do not carry passengers on

implement at any time.

For Your Protection

▲Thoroughly read and understand the “Safety Label” section, read all instructions noted on them.

Shutdown and Storage

▲Lower machine to ground, put tractor in park, turn off engine, and remove the key.

▲Detach and store implements in a area where children normally do not play. Secure implement by using blocks and supports.

OFF

9/24/08

RCR1884 Series Rotary Cutters 312-880M

1

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Rotary Cutters Table of Contents Be Aware Signal Words For Your ProtectionShutdown and Storage Transport Machinery Safely Use Safety Lights and DevicesUse a Safety Chain Practice Safe MaintenanceKeep Riders Off Machinery Prepare for EmergenciesWear Protective Equipment Avoid High Pressure Fluids Hazard818-543C Safety Labels818-540C 818-552C818-230C 818-556C 818-564C818-130C Using This Manual ApplicationOwner Assistance Land Pride Cat. l Adapter Bushings Vent Plug InstallationTractor Requirements Category l Adapter BushingsPoint Hitch Assembly Tighten all locknuts to correct torque Single Tailwheel AssemblyDual Tailwheel Assembly Front Guard Assembly Front Rubber Guard InstallationFront Chain Guard Installation Optional Rear Chain Guard Installation Optional Rear Metal Deflector AssemblyPoint Tractor Hook-Up Refer to -12 on Driveline InstallationDriveline Minimum Length Refer to -10 onDriveline Shortening Deck Leveling From Front to Rear Leveling ProcedureTop Center Link Length Adjustment Deck Leveling From Left to RightDual Tail Wheel Height Adjustment Single Tail Wheel Height AdjustmentUn-hooking the Rotary Cutter Operating ChecklistOperating Check List TransportingGeneral Operating Instructions Cutting Instructions22 RCR1884 Series Rotary Cutters 312-880M Accessories Front and Rear Safety Guard OptionsMaintenance Cutter Blade MaintenanceRefer to -2 on Refer to Refer to Figure Driveline ProtectionLand Pride Cutter Blade Parts Clutch Run-InClutch Inspection Clutch DisassemblyClutch Assembly Cutter StorageGauge Wheel Hub LubricationHours Gauge Wheel Spindle TubeDriveline U-Joints Driveline Shield BearingsDriveline Profiles RCR1884 RCR1884 ModelFeatures Benefits Features & BenefitsClutch slipping Problem Cause Solution Oil seal leakingDriveline yoke or cross failing DrivelineProblem Cause Solution Excessive vibration Torque Values Chart for Common Bolt Sizes Additional Torque ValuesIn-tpi Ft-lb Mm x pitch 34 RCR1884 Series Rotary Cutters 312-880M Overall Unit and Driveline One year Parts and Labor WarrantyCorporate Office P.O. Box Salina, Kansas 67402-5060 USA
Related manuals
Manual 32 pages 25.68 Kb

RCR1884 specifications

The Land Pride Rotary Cutter RCR1884 is an exceptional piece of equipment designed to meet the needs of landowners, farmers, and contractors looking for reliability and performance in their land management tasks. This rotary cutter is engineered for cutting grass, weeds, and brush, making it an ideal choice for maintaining fields, pastures, and right-of-ways.

One of the standout features of the RCR1884 is its cutting width of 84 inches, allowing users to cover a large area efficiently. The heavy-duty construction ensures durability and longevity, with a robust design that can withstand tough operating conditions. The RCR1884 is built with a thick steel frame, ensuring stability and strength while in operation.

Equipped with a powerful gearbox, the RCR1884 delivers consistent power and performance. The gearbox is designed for low maintenance, which reduces downtime and increases productivity. This rotary cutter also features a dual blade system, which provides a smooth and clean cut while minimizing the risk of plugging, making it suitable for different types of terrain.

Safety is a priority in the design of the RCR1884. It is equipped with safety shields and guards that protect the operator from debris and potential hazards during operation. The cutter's slip clutch further enhances safety by protecting the driveline and limiting damage in the event of an unexpected obstruction.

The RCR1884 is designed for easy attachment to tractors, featuring a standard Category 1 hitch that offers versatility and compatibility with a variety of equipment. This makes it a practical choice for users who need to switch tools frequently.

Another notable aspect of the RCR1884 is its ability to handle various cutting conditions. It performs effectively in both light and heavy vegetation, making it suitable for everything from routine lawn care to more intensive brush clearing tasks. The adjustable cutting height allows operators to set the blades at the desired height, ensuring versatility based on specific needs.

In summary, the Land Pride Rotary Cutter RCR1884 is a robust and efficient tool for anyone involved in land management. With its generous cutting width, durable construction, powerful gearbox, and safety features, it is well-equipped to tackle a wide range of cutting tasks. Whether you are maintaining a small property or operating on larger agricultural land, the RCR1884 is designed to deliver reliable performance and exceptional results.
Top Page Image Contents