Land Pride RCR1884 manual Cutter Storage, Clutch Disassembly, Clutch Inspection, Clutch Assembly

Page 28

Table of Contents

Section 5: Maintenance and Lubrication

Land Pride

Clutch Disassembly

Refer to Figure 5-4 on page 26:

Disassembly of the clutch is simply a matter of removing the spring retainer nuts (#1), springs (#2) and bolts (#3) from the assembly. Each friction disc (#4) must then be separated from the metal surface adjacent to it.

Clutch Inspection

Inspect all parts for excessive wear and condition. Clean all parts that do not require replacement.The original friction disc thickness is 1/8" (3.2 mm) and should be replaced if thickness falls below 3/64" (1.1 mm). If clutches have been slipped to the point of “smoking”, the friction discs may be damaged and should be replaced. Heat build-up may also affect yoke joints.

Clutch Assembly

Refer to Figure 5-4:

Reassemble each friction disc (#4) next to the metal plate it was separated from. Install bolts (#3) through the end plates and intermediate plates as shown. Place springs (#2) over the bolts and secure with nuts (#1).

19783

Clutch Disassembly

Figure 5-4

Refer to Figure 5-5:

Install new friction discs if needed and reassemble all components in proper order. Progressively tighten each spring retainer nut until spring length is 1.283” (1 9/32”).

24664

Clutch Adjustment

Figure 5-5

Cutter Storage

It is good practice to clean off any dirt or grease that may have accumulated on the cutter and on any moving parts at the end of a working season or when the cutter will not be used for a long period.

!DANGER

Always disconnect main driveline from tractor PTO and secure cutter deck in the up position with solid supports before servicing the underside of the cutter.

1.Clean cutter of all debris.

2.Check blades for wear and replace if necessary, see “Cutter Blade Maintenance” on page 24.

3.Inspect cutter for loose, damaged or worn parts and adjust or replace as needed.

4.Lubricate as noted under “Lubrication” on page 27.

5.Store cutter inside when possible to prolong its life.

6.Repaint parts where paint is worn or scratched to prevent rust. Ask your dealer for Aerosol Land Pride touch-up paint.

 

Land Pride Touch-up Paint

Part No.

Part Description

 

 

821-011C

PAINT LP BEIGE SPRAY CAN

821-032C

PAINT LP GLOSS BLACK SPRAY CAN

 

 

26 RCR1884 Series Rotary Cutters 312-880M

9/24/08

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Rotary Cutters Table of Contents For Your Protection Be Aware Signal WordsShutdown and Storage Use Safety Lights and Devices Use a Safety ChainPractice Safe Maintenance Transport Machinery SafelyPrepare for Emergencies Wear Protective EquipmentAvoid High Pressure Fluids Hazard Keep Riders Off MachinerySafety Labels 818-543C818-552C 818-540C818-556C 818-564C 818-230C818-130C Application Using This ManualOwner Assistance Vent Plug Installation Tractor RequirementsCategory l Adapter Bushings Land Pride Cat. l Adapter BushingsPoint Hitch Assembly Single Tailwheel Assembly Tighten all locknuts to correct torqueDual Tailwheel Assembly Front Rubber Guard Installation Front Guard AssemblyFront Chain Guard Installation Optional Rear Metal Deflector Assembly Rear Chain Guard Installation OptionalPoint Tractor Hook-Up Driveline Installation Driveline Minimum LengthRefer to -10 on Refer to -12 onDriveline Shortening Leveling Procedure Top Center Link Length AdjustmentDeck Leveling From Left to Right Deck Leveling From Front to RearSingle Tail Wheel Height Adjustment Dual Tail Wheel Height AdjustmentOperating Checklist Operating Check ListTransporting Un-hooking the Rotary CutterCutting Instructions General Operating Instructions22 RCR1884 Series Rotary Cutters 312-880M Front and Rear Safety Guard Options AccessoriesCutter Blade Maintenance MaintenanceRefer to -2 on Driveline Protection Land Pride Cutter Blade PartsClutch Run-In Refer to Refer to FigureClutch Disassembly Clutch AssemblyCutter Storage Clutch InspectionLubrication HoursGauge Wheel Spindle Tube Gauge Wheel HubDriveline Shield Bearings Driveline U-JointsDriveline Profiles RCR1884 Model RCR1884Features & Benefits Features BenefitsProblem Cause Solution Oil seal leaking Driveline yoke or cross failingDriveline Clutch slippingProblem Cause Solution Excessive vibration Additional Torque Values Torque Values Chart for Common Bolt SizesIn-tpi Ft-lb Mm x pitch 34 RCR1884 Series Rotary Cutters 312-880M Warranty Overall Unit and Driveline One year Parts and LaborCorporate Office P.O. Box Salina, Kansas 67402-5060 USA
Related manuals
Manual 32 pages 25.68 Kb

RCR1884 specifications

The Land Pride Rotary Cutter RCR1884 is an exceptional piece of equipment designed to meet the needs of landowners, farmers, and contractors looking for reliability and performance in their land management tasks. This rotary cutter is engineered for cutting grass, weeds, and brush, making it an ideal choice for maintaining fields, pastures, and right-of-ways.

One of the standout features of the RCR1884 is its cutting width of 84 inches, allowing users to cover a large area efficiently. The heavy-duty construction ensures durability and longevity, with a robust design that can withstand tough operating conditions. The RCR1884 is built with a thick steel frame, ensuring stability and strength while in operation.

Equipped with a powerful gearbox, the RCR1884 delivers consistent power and performance. The gearbox is designed for low maintenance, which reduces downtime and increases productivity. This rotary cutter also features a dual blade system, which provides a smooth and clean cut while minimizing the risk of plugging, making it suitable for different types of terrain.

Safety is a priority in the design of the RCR1884. It is equipped with safety shields and guards that protect the operator from debris and potential hazards during operation. The cutter's slip clutch further enhances safety by protecting the driveline and limiting damage in the event of an unexpected obstruction.

The RCR1884 is designed for easy attachment to tractors, featuring a standard Category 1 hitch that offers versatility and compatibility with a variety of equipment. This makes it a practical choice for users who need to switch tools frequently.

Another notable aspect of the RCR1884 is its ability to handle various cutting conditions. It performs effectively in both light and heavy vegetation, making it suitable for everything from routine lawn care to more intensive brush clearing tasks. The adjustable cutting height allows operators to set the blades at the desired height, ensuring versatility based on specific needs.

In summary, the Land Pride Rotary Cutter RCR1884 is a robust and efficient tool for anyone involved in land management. With its generous cutting width, durable construction, powerful gearbox, and safety features, it is well-equipped to tackle a wide range of cutting tasks. Whether you are maintaining a small property or operating on larger agricultural land, the RCR1884 is designed to deliver reliable performance and exceptional results.
Top Page Image Contents