Land Pride FD2548 manual Maintenance, Lubrication

Page 10

MAINTENANCE

1/29/04

!For SAFETY REASONS, each maintenance operation must be performed with the tractor’s PTO dis- engaged, the Mower lowered completely to the ground or on safely supported blocking, tractor engine shut off and ignition key removed.

Proper servicing and adjustments is the key to the long life of any machine. With careful and systematic inspection of the Grooming Mower, you can avoid costly maintenance, time and repair.

BLADE SHARPENING -

1.Blades should be sharpened at each end to the same angle as the original cutting edge.

NOTE: Care should be taken in order not to remove any more material than necessary to sharpen blade.

2. Balance each blade after sharpening.

BLADE REPLACEMENT -

IMPORTANT: ALWAYS install blade with cutting edge facing direction of rotor shaft rotation.

1.Remove cap screw and blade washer from blade to be replaced. Remove blade.

2.Install blade washer into center hole on blade.

3.Replace cap screw and lock washer and tighten bolts to proper torque. See "Nut & Bolt Torquing Chart" on page 4.

IMPORTANT: Replace blades with genuine Land Pride blades only.

!CAUTION! BELT DRIVE SYSTEM UNDER SPRING TENSION; USE CARE TO AVOID BODILY HARM!

V-BELT INSTALLATION -

1.Remove belt covers.

2.Move belt take-up handle in a clockwise direction to relieve tension on belt.

3.With tension relieved from belt remove old belt from pulleys.

4.Install new belt referring to the figure below (also re- fer to the decal on top of mower deck). Be sure belt is positioned in all the pulley grooves. Release belt take- up handle to apply tension to new belt.

5.Reinstall all belt covers and secure in place with hardware.

LUBRICATION

SERVICE DAILY:

1.Grease the PTO u-joints.

2.Wheel support bushings.

3.Wheel bushing.

4.Bearing in blade spindle hubs.

NOTE: There is a small relief hole on each spindle hub casting on the underside of the deck. The relief hole re- leases pressure from inside the spindle hub casting when being greased. Spindle hubs should be greased until grease purges from relief hole.

SERVICE EVERY 50 HOURS OF OPERATION:

1.With the mower on level ground, check the oil level in the gearbox by removing the plug in the side of the box. The oil should reach the plug hole. If oil level is low, remove the top plug in the gearcase and fill with SAE 90 oil until oil flows from side port of the gearbox. Reinstall plugs and retighten. DO NOT OVERFILL! Should your gearbox require service, take it to your LAND PRIDE dealer.

IMPORTANT: Mower should be level when check- ing oil in gearbox!

2.Disconnect PTO shaft from the tractor and slide apart. Clean and coat the inner tube of the PTO shaft with a light film of grease and then reassemble.

9

Image 10
Contents Spindle Grooming Mower Table of Contents IntroductionSafety Rules Safety Rules CON’T Safety Decals Rotating Cutting BladeTractor Requirements NUT & Bolt Torquing ChartAssembly Instructions Gear BOX Gear LubeFloating and Front to Back Hitch Adjustments Assembly Instructions CON’TPowershaft Installation Tractor HOOK-UPFront to Rear Leveling the MowerSide to Side Mowing Instructions and Adjustments Cutting Height AdjustmentTransporting Operating Instructions SpecificationsOperating Check List Maintenance LubricationStorage OptionsMower Chain KIT Assembly Instructions Options CON’TCharge Chute When Trouble ShootingNot TRY to Clean DIS MowerWarranty Flat Deck Mower Deck & Components Flat Deck Mower Deck & Components CON’T Flat Deck Mower Belt Drive Flat Deck Mower Belt Drive CON’T Comer Gearbox Part no -011C Comer Gearbox CON’T Part no -011CIEG Gearbox IEG Gearbox CON’T Gauge Wheel Assembly Gauge Wheel Assembly CON’T Power TAKE-OFF Part no -012C Options Front ANTI-SCALPING Roller Part no -077SOptions Chain KIT Decal Placement 29/04 Corporate Office P.O. Box 5060 Salina, Kansas 67402-5060 USA

FD2548 specifications

The Land Pride FD2548 is a robust and dependable flail mower designed for professional landscaping, agriculture, and non-commercial use. This mower stands out for its ability to handle a variety of mowing applications with efficiency and precision. Boasting a cutting width of 48 inches, the FD2548 is engineered to tackle tough vegetation and maintain a clean finish across diverse terrains.

One of the main features of the Land Pride FD2548 is its heavy-duty construction. It is built with high-quality materials, ensuring durability and longevity even under rigorous conditions. The mower is equipped with a rugged frame that provides stability and strength during operation. The rotating flail blades are particularly noteworthy; they are designed to efficiently chop through dense grass, weeds, and brush, making it an ideal choice for overgrown areas.

The FD2548 incorporates advanced mower technology to enhance cutting performance. Its flail blade system utilizes multiple blades that rotate around a horizontal shaft, delivering a finely shredded finish that decomposes quickly, enriching the soil. The blades are replaceable, allowing users to easily maintain optimal performance and efficiency. This mower also features adjustable cutting height settings, providing flexibility to achieve the desired grass length while accommodating various landscaping needs.

Another characteristic that sets the Land Pride FD2548 apart is its compatibility with multiple tractor models. It features a category 1 quick hitch system, allowing for easy attachment and detachment without the need for additional tools. This versatility makes it a favorite among farmers, landscapers, and large property owners, enabling users to switch between implements quickly and efficiently.

Additionally, the FD2548 is designed with operator safety in mind. It includes features such as a rear discharge design that prevents clippings from being ejected towards the operator, ensuring a safer working environment. The mower is also relatively easy to service, with accessible grease fittings and a user-friendly design that simplifies routine maintenance.

In summary, the Land Pride FD2548 flail mower excels in durability, versatility, and cutting performance. Its heavy-duty construction, advanced flail technology, adjustable height settings, and safety features make it an excellent choice for anyone looking to maintain their property effectively and efficiently. Whether you're managing a large farm or tending to a residential landscape, the FD2548 is engineered to deliver results with reliability and precision.