Land Pride BH2585 manual Backhoe Stabilizer Kit Installation

Page 16

Table of Contents

Section 1 Assembly and Set-Up

Land Pride

7.Extend boom and lower dipper stick and stabilizers until they contact the ground.

8.By manipulating the cylinder and placing down pressure on the boom and stabilizers, lift the backhoe vertically to approximately 8” to 12” of ground clearance. See Figure 1-9.

9.Attach the backhoe to the lower lift arms of the tractor using the pins (#7) in Figure 1-8.

Backhoe Stabilizer Kit Installation

Refer to Figure 1-10:

1.Assemble drawbar bracket (#2) to the tractor drawbar 1” from drawbar support with 5/8” U-bolts (#8) ﬂat washers (#6) nuts (#4) and jamnuts (#5). The spacers (#1) may have to be used on 2” and 2 1/4” drawbars.

2.Insert bolt (#3) (drill 5/8” hole if necessary) secure with ﬂat washer (#6) nut (#4) and jam nut (#5).

3.Install stabilizer links (#10) as shown and insert clevis pins (#9) and secure with linchpins (#7). Stabilizer links can be adjusted at both ends to ﬁt your tractor.

8” to 12”

20565

Ground Clearance

Figure 1-9

To tractor upper 3-point

No more than 1” from draw bar support

Stabilizer Kit Installation
Figure 1-10	20571

14

10/28/05

Image 16

Contents Backhoes Table of Contents Important Safety Information Look For The Safety Alert SymbolBe Aware Signal Words For Your ProtectionUse Safety Lights and Devices Transport Machinery SafelyTransporting the Loader and Attachment Keep Riders Off MachineryPractice Safe Maintenance Prepare for EmergenciesWear Protective Equipment Avoid High Pressure Fluids Hazard838-380C 838-378C 838-379C818-339C 839-933C 839-932C Using This Manual ApplicationOwner Assistance Serial Number PlateBackhoe Operation, Maintenance & Safety Tips Power Beyond Hydraulic Systems Assembly and Set-UpTractor Requirements Skid Steer RequirementsPower Beyond & Closed Center Kit Closed Center Hydraulic SystemsChoose the Appropriate Hosing Independent PTO Hydraulic Pump SystemBackhoe Independent Hydraulic Systems For All Tractors For John Deere TractorsMounting The Backhoe Main Frame Boom Cylinder Inside Boom Stabilizer CylinderLower Link Hitch Bracket Installation Transport LockBackhoe Stabilizer Kit Installation Bucket Installation Seat AssemblySkid Steer Hook-Up Locking Bar Optional Equipment AssembliesRipper Tooth Preparing For Operation Operating The BackhoeTransporting The Backhoe Operating InstructionsBoom Control FunctionsDipper Stick And Bucket Digging Suggestions Digging at the Correct AngleObserve the following cautions while digging Dipper Stick & Boom AngleBucket Angle Maintenance Bucket Tooth ReplacementMaintenance and Lubrication StorageLubrication Bucket PivotBucket Pivot End of Stick Bucket Cylinder Base EndDipper Stick Cylinder Base End Boom Cylinder Rod EndBoom Pivots Both Sides Boom Pivot Unerneath at end of BoomBoom Cylinder Base End Stabilizer Cylinder Rod End Both SidesStabilizer Arms Both Sides Boom Swing PivotBoom Swing Cylinder Rod End Both Sides Boom Swing Cylinder Base EndBH25 Series Backhoes Speciﬁcations and CapacitiesBH2585 Features and Beneﬁts Features BenefitsTroubleshooting Problem Cause Solution Load drops when valveHydraulic System PerformanceTorque Values Chart For Common Bolt Size AppendixIn-tpi · m Ft-lb Mm x pitchWarranty Corporate Ofﬁce P.O. Box Salina, Kansas 67402-5060 USA